Dungs DMV Series Manuel utilisateur

1 … 2

MC • Karl Dungs, Inc. • DMV/6x2 Series Coil Replacement • Edition 2016.02 • P/N 261408

DMV/6x2 Series

Coil Replacement

Installation Instructions

Table of Contents

USA CDN

Table of Contents ........................Page 1

Attention ................................Page 1

Procedure ...............................Page 2

1, 2, 3 ... = Action

• = Instruction

Explanation of symbols

On completion of work on the

safety valve, perform a leakage

and function test.

Please read the instruction be-

fore installing or operating. Keep

the instruction in a safe place. You

nd the instruction also at www.

dungs.com If these instructions

are not heeded, the result may

be personal injury or damage to

property.

Any adjustment and application-

specic adjustment values must

be made in accordance with the

appliance-/boiler manufacturers

instructions.

Attention

Check the ratings in the speci-

cations to make sure that they

are suitable for your application.

[V][A]

[Hz][VA]

Safety

first

O.K.

Theinstallationandmaintenance

of this product must be done

under the supervision of an ex-

periencedand trainedspecialist.

Never perform work if gas pres-

sure or power is applied, or in

the presence of an open ame.

2 … 2

MC • Karl Dungs, Inc. • DMV/6x2 Series Coil Replacement • Edition 2016.02 • P/N 261408

Procedure

1. Disconnect all power to prevent electrical shock and

equipment damage.

2. Closetheupstreammanualshutovalve.

3. Remove DIN electrical connector.

4. Remove blue paint from the countersunk screw on the

hydraulic brake unit (DMV-DLE series) or black adjustment

knob (DMV-D series). (Fig. 1)

5. Remove the pan head screw on the hydraulic brake unit

(DMV-DLE series) or black adjustment knob (DMV-D

series). (Fig. 1)

6. Liftothehydraulicbrakeunitorblackadjustmentknob.

7. Remove washer.

8. Remove solenoid by pulling directly up. Note solenoid #

and voltage.

9. Verify the replacement coil has the same coil # and electri-

cal rating. Install replacement coil.

10.Replace washer.

11. Check the o-rings (clean if necessary) on the hydraulic

brake unit or black adjustment knob.

12.Remount the hydraulic brake unit or black adjustment

knob. During mounting, take care not to damage the

o-rings on the shaft of the hydraulic brake on DMV-

DLE models and the adjustment knob on DMV-D

models.

13.Install and secure screws to the hydraulic brake unit or

black adjustment knob. Take care not to overtighten

14.With the gas pressure applied and valve #1 energized or

with both valve energized, perform an external leakage

test: Apply liquid leak detector around the gap between

the hydraulik brake unit or black adjustment knob, the

valve body and the solenoid.

15.If bubbles form, remove hydraulic brake unit or black

adjustment knob. Check and clean o-rings. (If o-rings

are damaged contact Karl Dungs, Inc. for a replacement

hydraulic brake or black adjustment cap.) Inspect the

bore in the cylinder shaft. Make sure it does not contain

any debris or burrs. Make sure no dirt can come into the

valve system. Remount the hydraulic brake unit or black

adjustment knob. Perform leakage test again. If the valve

still leaks contact Karl Dungs, Inc.

16.If no leak is detected, connect the DIN electrical connector.

17. Perform a complete function test: apply power to the valve,

make sure both valves open and close properly.

18.If the valve does not operate properly, contact Karl Dungs,

Inc. for technical help or replacement.

Karl Dungs GmbH & Co. KG

P.O. Box 12 29

D-73602 Schorndorf, Germany

Phone +49 (0)7181-804-0

Fax +49 (0)7181-804-166

e-mail info@dungs.com

Internet http://www.dungs.com

Karl Dungs, Inc.

3890 Pheasant Ridge Drive NE

Suite 150

Blaine, MN 55449, U.S.A.

Phone 763 582-1700

Fax 763 582-1799

e-mail info@karldungsusa.com

Internet http://www.dungs.com/usa/

Autres manuels Dungs Unité de contrôle

Dungs

Dungs GasMultiBloc MB-D B07 Series Manuel utilisateur

Dungs

Dungs FRM 100025 Manuel utilisateur

Dungs

Dungs DMK 5040 Manuel de service

Dungs

Dungs VDK 200 A S02 Manuel de service

Dungs

Dungs SAV 100065 Manuel utilisateur

Dungs

Dungs SAV 100065 MD Manuel utilisateur

Dungs

Dungs DSLC px Vx Manuel de service

Dungs

Dungs GSV Series Manuel utilisateur

Dungs

Dungs VPM-VC Manuel utilisateur

Dungs

Dungs VPM-VC Manuel utilisateur

Dungs

Dungs DGAI. 33F/2 Manuel de service

Dungs

Dungs VDK 200 Manuel de service

Dungs

Dungs DMV 11 eco Series Manuel de service

Dungs

Dungs VPS 504 Manuel de service

Dungs

Dungs GasMultiBloc MBC-65 Series Manuel utilisateur

Dungs

Dungs FRSBV Manuel utilisateur

Dungs

Dungs MB-ZR B07 Series Manuel utilisateur

Dungs

Dungs DGAI. 20/5 Guide produit

Dungs

Dungs SV-DLE 1005/604 Manuel de service

Dungs

Dungs GasMultiBloc MB-VEF B01 Manuel utilisateur

Dungs

Dungs MultiBloc MBE-S Series Manuel utilisateur

Dungs

Dungs FRSBV 20010 Series Manuel utilisateur

Dungs

Dungs VPM-LC Manuel utilisateur

Dungs

Dungs DMV-D(LE) 704/6x4 Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur