Dormakaba ED connection board CAN Manuel utilisateur

Assembly Instruction

ED connection board CAN

060636 45532/16923 - 2023-04

Table of contents Assembly Instruction

2 ED connection board CAN 060636 45532/16923 - 2023-04

Table of contents

1 Information about this document 3

1.1 Contents and purpose 3

1.2 Target group 3

1.3 Other applicable documents 3

1.4 Abbreviations 3

1.5 Symbols used 3

1.5.1 Hazard category 3

2 Safety 3

3 Product description 4

3.1 Product description 4

3.2 Technical data 4

3.3 Structure of the ED connection board CAN 4

3.4 LED display 5

4 Mounting 6

4.1 Note the structure of the ED 100/250 drive 6

4.2 Mounting the ED connection board CAN 7

5 Connection 10

6 Commissioning 11

7 Troubleshooting 11

7.1 Error display 11

8 Disassembly and disposal 12

Assembly Instruction Information about this document

060636 45532/16923 - 2023-04 ED connection board CAN 3

1 Information about this document

1.1 Contents and purpose

This document describes the mounting and connection of the ED connection

board CAN to an ED100/250 operator.

1.2 Target group

The product may only be mounted and commissioned by a qualified electrician.

1.3 Other applicable documents

• Mounting and commissioning ED 100/250

• Radar sensor M A01 mounting instructions

1.4 Abbreviations

Abbreviation Definition

ED100/250 Electromechanical swing door operators for the

automatic opening and closing of swing doors.

1.5 Symbols used

1.5.1 Hazard category

NOTICE

Means a potentially harmful situation where the product or

something in its environment could be damaged or result in

malfunction.

2 Safety

WARNING

Danger due to failure of protective and safety equipment

The cable routing connects the installed components with each other.

Unprotected cable routing can lead to tampering or malfunctions.

• Lay cables either flush-mounted or

• surface-mount the cables in the steel hose

NOTICE

Material damage due to electrostatic discharge

The component can be damaged by electrostatic discharge!

• Ground your body before touching the component.

• Use ESD safe tool.

Product description Assembly Instruction

4 ED connection board CAN 060636 45532/16923 - 2023-04

3 Product description

3.1 Product description

The ED connection board CAN is a board that is required to make an ED100/250

CAN-capable. It replaces the standard plate in ED and is compatible from

firmware V2.9.000 and up.

3.2 Technical data

Supply

voltage

24 V DC +/- 15 %

Power consumption approx. 20 mA quiescent cur-

rent

Temperature range -15°C to +50°C

Rel. humidity up to 93%, non-condensing

ED protection class IP20

Dimensions Length 88 mm

width 60 mm

height 26 mm

3.3 Structure of the ED connection board CAN

1 2 3

78910

Position Layout

1 Locking device

2 Fire protection

3 Emergency stop

4 RS232 interface connection socket

5 Radar sensors M A01 CAN connection cable connection terminals

6 RGB LED function display

Assembly Instruction Product description

060636 45532/16923 - 2023-04 ED connection board CAN 5

Position Layout

7 Ribbon cable connection socket

8 CAN connection cable EntriWorX connection terminals

9 CAN connection cable EntriWorX connection plug

10 Safety sensors

11 Signal inputs for night/bank, impulse outside and impulse inside

The operating conditions specified in the mounting and commissioning instructions

for ED 100/250 operators apply to the ED connection board CAN.

3.4 LED display

The RGB LED function display on the ED connection board CAN is defined as a

secondary function display. The RGB LED function display uses signal colors to

show the current operating status or a fault.

To see the signal colors of the RGB LED function display, remove the ED 100/250

operators’ cladding.

Signal no. Color Description Meaning

1 permanently

red

Self-test error display Self-test error occurred or

CAN device detection is

faulty.

2 Flashing

green

Identification display The device identification is

activated.

3 Flashing yel-

low

CAN device mapping The device assignment is ac-

tive after a CAN reset. De-

vice assignment ends when

the assignment is com-

pleted without errors or

when an error occurs.

4 Flashing red Error display One or more errors are

pending. Error number with

the highest priority is indi-

cated by the number of

flashes.

See “Evaluate errors and rectify faults”.

Signal no. Color Description Meaning

5 Glowing white TMS initialization TMS bus initialization for

sensor and ED connection

board CAN running.

6 Green light: Display operating status

The system is working with-

out errors.

Mounting Assembly Instruction

6 ED connection board CAN 060636 45532/16923 - 2023-04

4 Mounting

4.1 Note the structure of the ED 100/250 drive

1 3 4 5 6

The graphic shows the ED operator for the left door leaf of a 2-leaf door . Further

information on the installation position and settings of the ED operators can be

found in the mounting and commissioning instructions for the ED 100/250.

Position Meaning

1 Power on

2 Standard ED connection board

3 Complete cladding

4 Ribbon cable

5 RJ45 socket (COM 1)

6 User interface with information display

7 Adapter for internal program switch

8 Side cover

Assembly Instruction Mounting

060636 45532/16923 - 2023-04 ED connection board CAN 7

4.2 Mounting the ED connection board CAN

Note Structure of the ED connection board CAN [}3.3].

1. Set the parameter "C1 -> Configuration of the COM1 interface (vertical plug)"

to "1".

2. Switch off the ED operator on the active door leaf (power switch to "0").

3. Remove the cladding (3) from the active door leaf operator, see “Note the

structure of the ED 100/250 drive [}4.1]”.

4. Pull the ribbon cable (4) out of the standard ED connection board (2), see

“Note the structure of the ED 100/250 drive [}4.1]".

5. Remove the plug from the board.

6. Press the locking elements inwards in the suggested order and remove the

standard ED connection board (2), see “Note the structure of the ED 100/250

drive [}4.1]”.

7. Insert the cable ends of the connection cables from the inside to the empty

board slot.

8. Plug the ED connection board CAN over the locking elements.

9. Plug in the plugs and connect the lines.

10. Pull the open cable end of each CAN connection cable out through the middle

opening in the ED connection board CAN.

Mounting Assembly Instruction

8 ED connection board CAN 060636 45532/16923 - 2023-04

11. Connect the CAN connection cable to the connection terminals (5) for the

radar sensor M A01, see also Radar sensor M A01 mounting instructions.

Connect the CAN connection cable to the connection terminal for EntriWorX

(8), see also EntriWorX manual.

Connect the CAN connection cable to the connector plug for EntriWorX (9),

see also EntriWorX manual.

12. Pull out the open cable ends of all other cables and connect them.

13. Connect all other cables according to the mounting and commissioning

instructions for the ED100/250.

14. Plug the ribbon cable back into the connection socket (7), see "".

15. Insert the serial connection cable into the connection socket (4).

16. NOTICE!Guide/stow all cables inside the operator in the cable ducts or

secure with a cable holder to prevent collisions with moving parts!

17. Plug the RJ45 plug of the serial connection cable into the socket (5) next to

the user interface (6), see “Note the structure of the ED 100/250 drive [}4.1]”.

Assembly Instruction Mounting

060636 45532/16923 - 2023-04 ED connection board CAN 9

ðThe ED connection board CAN is connected for commissioning.

18. For 2-leaf units, attach the adapter (6) for internal program switch.

19. Connect the external program switch to the adapter.

Connection Assembly Instruction

10 ED connection board CAN 060636 45532/16923 - 2023-04

5 Connection

35 41 42 3

1631 4 4a

31G63

64343

3111317151 13

1 2 3

Number Assignment

1 43 Locking feedback

3 GND

64 NC

63 NO

62 COM

1G + 24 V switched depending on the smoke detector

3 GND

2 1 + 24V

3 GND

6 Fire protection upgrade card

18k or RM ED

3 4 Shutdown drive function

4a GND

10 1 + 24V

15 Signal input safety sensor hinge side

17 Test output

3 GND

1 + 24V

11 Signal input safety sensor opposite side to the hinge

13 Test output

3 GND

11 35 Signal input night/bank

41 Signal input impulse outside

42 Signal input pulse inside

3 GND

Table des matières

Autres manuels Dormakaba Unité de contrôle

Dormakaba

Dormakaba SCU-DR Guide de l'utilisateur

Dormakaba

Dormakaba SafeRoute SCU-UP Manuel utilisateur

Dormakaba

Dormakaba MotionIQ ED-CAN Manuel utilisateur

Dormakaba

Dormakaba SLI-A Interlock Manuel utilisateur

Dormakaba

Dormakaba SIO-DR Manuel utilisateur

Dormakaba

Dormakaba LA GARD 700 Series Manuel utilisateur

Dormakaba

Dormakaba MFC Manuel utilisateur

Dormakaba

Dormakaba UNIQUIN Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur