DMP Electronics 1125 Instructions de montage

INSTALLATION SHEET

FIELD TEST VERSION 7/28/2004

1125 PIR Motion Detector

Description

The 1125 PIR (Passive Infrared) Motion Detector is a wireless, low current sensor for use with the 1100D Wireless

Receiver. Using mirrored optic technology the 1125 PIR is highly immune to multiple false alarm sources. In addition

to switch-selectable sensitivity and range adjustment, you can use masking to modify coverage patterns for various

applications.

Parts Included

• One PIR detector

• Three 3V lithium CR-123A batteries

• Two plastic masks

• One screw to secure the unit to the wall mounting bracket

• One wall-mounting bracket

• One sheet of adhesive masking labels

• One cardboard undercrawl window mask

For your convenience, two additional pre-printed serial number

labels are included. Verify the serial numbers on the labels match

the serial number located on the back of the device housing. Prior

to installing the device, record the serial number located on the

back of the device housing or place one of the pre-printed serial

number labels on the panel programming sheet. This number is

required during programming.

Selecting a Location

Mount the unit:

• On a rigid vibration-free surface

• 6 to 10 feet (1.8 to 3m) high, but at least 6 inches (15cm) from the ceiling

• So the expected intruder movement is across the detection pattern elds, see Figure 2

Do not locate the unit:

• On a surface exposed to moisture

• In any area containing excessive metallic surfaces

• Where it may be exposed to false alarm sources such as: direct sunlight, heat sources (heater, radiators, etc.)

in the eld of view or strong air drafts (fans, air conditioner, etc.)

• Where the ambient temperature is below 32° F (0°C) or above 131°F (55°C)

Figure 2: Detection Pattern

Figure 1: 1125 PIR Exploded View

Digital Monitoring Products 1125 PIR Installation Sheet

1125 PIR Installation Sheet Digital Monitoring Products

Selecting the Coverage Pattern

The unit coverage pattern can be modied to t specic applications by masking mirror curtains. Mask curtains to

avoid sources of false alarms, such as heaters, air conditioners, and windows. Open the unit by pushing the opening

tab up. If necessary, use one or more of the following methods to modify the coverage pattern.

Using the plastic masks

Use one or both of the plastic masks provided to mask off large coverage areas as shown in Figure 3.

Figure 3: Plastic Masks

Using the adhesive labels

Mask the appropriate mirror curtains with the provided adhesive labels. See the example shown in Figure 4. Do not

use sharp objects to remove unwanted labels. If necessary, carefully peel off the label.

Figure 4: Adhesive Labels

Using the cardboard masks

Use the cardboard undercrawl window mask as shown in Figure 5. The undercrawl mask allows objects to be placed

within 5 feet of, or directly below, the detector. When not using the mask as described here or in the Pet Alley

conguration, remove the mask completely.

Figure 5: Cardboard Masks

Digital Monitoring Products 1125 PIR Installation Sheet

1125 PIR Installation Sheet Digital Monitoring Products

Setting the Sensitivity and Range Switches

Use the switches located on the unit back to set sensitivity and range, as shown in Figure 6. Use the following to

determine the appropriate switch settings for an application.

Mode

BI = Bi-curtain Mode (factory default) increases false alarm immunity in smaller areas and requires an intruder

to pass through two curtains to trigger an alarm. Do not use for single curtain applications or ranges under 5 feet

(1.5 m).

STD = Standard Mode is used for wide-angle or single-curtain applications. This requires the intruder to only pass

through one curtain to trigger an alarm.

Range

Program the switch for a range under 33 feet (10.1 m) or up to 50 feet (15.2 m). It is important to program the unit

correctly for optimum sensitivity. Walk test the unit regularly by walking across the elds of view and checking that

the LED lights and that an alarm is indicated at the control panel. See Walk Testing.

Note: The LED only lights if the unit is placed in Walk test Mode by the installer and the unit is enrolled in the

system.

Mounting the Unit

Caution: You must be free of static electricity before handling sensor circuit boards. Touch a grounded, bare

metal surface before touching circuit boards or wear a grounding strap.

Prior to permanently mounting the PIR unit, access the device address label and check that the PIR and control

panel communication is working. See the Walk Testing section.

FCC Considerations

The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all

persons. It must not be co-located or operated in conjunction with any other antenna or transmitter.

1. Separate the PIR unit from the mounting bracket. Refer to Figure 1 for details.

2. Insert a small at-head screwdriver between the tabs at the unit bottom and turn the screwdriver to push the

tabs apart.

3. Select the appropriate knockout mounting holes on the mounting bracket for either corner or at wall

mounting.

Note: Holes near the tamper actuator are not mounting knockouts.

4. Use screws and wall anchors, if necessary, to attach the mounting bracket to the wall. Do not over-tighten.

5. Snap the unit to the mounting bracket.

Digital Monitoring Products 1125 PIR Installation Sheet

1125 PIR Installation Sheet Digital Monitoring Products

Installing or Replacing Batteries

Note: You must remove all batteries to reset the low battery signal before installing new batteries. Always replace

all three batteries. Allow three minutes after installing the batteries for the sensor to become operational before

initiating a Walk Test.

Use only 3V lithium CR-123A batteries. Use the following steps to install the batteries:

1. Remove the unit from the wall mounting bracket. See Mounting the Unit.

2. Remove all batteries (if installed) before installing new batteries.

3. Observe polarity and insert the three lithium batteries into the battery holder where indicated in Figure 6.

Caution: Risk of re, explosion, and burns. Do not recharge, disassemble, heat above 212°F (100°C), or

incinerate. Properly dispose of unused batteries.

Tamper

Opening Tab

Battery

Compartment

Switches

Switch Settings

33'

(10.1m)

50'

(15.2m)

STD

Figure 6: 1125 PIR Switches

Programming the PIR in the Panel

Refer to the panel programming guide as needed. Program the device as a zone in Zone Information during panel

programming. Typically select the Night or Exit zone type for the 1125 PIR. At the Serial Number: prompt, enter the

serial number recorded from the back of the device case. Continue to program the zone as directed in the panel

programming guide.

Note: When a receiver is installed or powered down and powered up or the panel is reset, the supervision timer

cycle restarts.

Note: You can re-use a device in another system after the serial number has been previously programmed. Remove

the device battery, press and hold the tamper switch for one second to clear the panel house code from the device

memory and set the device back to factory defaults.

Digital Monitoring Products 1125 PIR Installation Sheet

1125 PIR Installation Sheet Digital Monitoring Products

PIR Walk Testing

A Walk test Mode for testing the unit operation and coverage pattern is provided. Use the following instructions to

walk test the unit:

1. Ensure the 1125 PIR is programmed in the Command Processor™ panel.

2. Lift the unit from the bracket until the tamper switch opens to enable the Walk test Mode.

3. When the unit is remounted on the bracket, the unit remains in the Walk test Mode for 3-4 minutes. If

additional time is required, depressing and releasing the tamper switch resets the Walk test timer. Depending

on switch settings (see Selecting the Coverage Pattern), the Walk test Mode allows the unit to alarm whenever

one or two curtain areas are entered. The LED visible on the front cover lights to indicate an alarm.

4. Walk test the detection pattern and make any necessary adjustments.

5. Replace and walk test the unit to verify the unit is communicating with the control panel.

Note: After Walk test Mode times out (3 to 4 minutes), the unit returns to normal operating mode. In normal

operating mode, the PIR unit activates approximately once every three minutes, and the LED disables to reduce

battery drain.

Maintenance

When installed and used properly, the unit provides years of service with minimal maintenance. To ensure proper

operation, you should walk test the unit annually as described in Walk Testing. Clean the inside of the unit with a

soft bristled brush or compressed air. Clean the cover with a water dampened cloth as needed to keep it free of

dust and dirt. Always test the unit after cleaning.

Pet Alley Application

To create a detection-free area close to the oor, mount the unit 3 feet (0.9 m) above the oor, upside down with

the detector window toward the ceiling. The undercrawl mask should be in place to reduce ceiling exposure.

Coverage distance is 25 feet in Bi-curtain Mode. As shown in Figure 7, pets are free to roam below the unit

mounting height without causing alarms. When not using the mask as described here or in the Using the cardboard

masks conguration, remove the mask completely.

Figure 7: Pet Alley

800-641-4282

www.dmp.com

Made in the USA

INTRUSION • FIRE • ACCESS • NETWORKS

2500 North Partnership Boulevard

Springfield, Missouri 65803-8877

Specications

Battery

Life 1 year (min)

Type 3.0V Lithium CR-123A

Transmit condition Alarm, tamper

Detection range 50 feet (15.2 m)

Mounting height 6 to 10 feet (1.8 to 3m)

Number of curtains 9

Operating temp. 32 to 131° F (0 to 55° C)

Relative humidity 10 to 93% non-condensing

Dimensions 5.1” H X 2.9” W X 2.2” D

Color White

Housing material Flame retardant ABS

Patent Information

Protected under pending U.S. and foreign patents.

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modications made by the user and not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Table des matières

Autres manuels DMP Electronics Capteur de sécurité

DMP Electronics

DMP Electronics 1128 Manuel utilisateur

DMP Electronics

DMP Electronics 1125 Instructions de montage

DMP Electronics

DMP Electronics 1161 Manuel utilisateur

DMP Electronics

DMP Electronics 1128 Manuel utilisateur

DMP Electronics

DMP Electronics 1128INT Manuel utilisateur

DMP Electronics

DMP Electronics 1124 Manuel utilisateur

DMP Electronics

DMP Electronics 1126R Manuel utilisateur

DMP Electronics

DMP Electronics 1121-WINT PIR Instructions de montage

DMP Electronics

DMP Electronics 1129 WIRELESS GLASSBREAK DETECTOR Manuel utilisateur

DMP Electronics

DMP Electronics 1183-135F Manuel utilisateur

DMP Electronics

DMP Electronics 1127C Manuel utilisateur

DMP Electronics

DMP Electronics SR3 Manuel utilisateur

DMP Electronics

DMP Electronics 1121 Instructions de montage

DMP Electronics

DMP Electronics XR Series Manuel utilisateur

DMP Electronics

DMP Electronics XT30INT Manuel utilisateur

DMP Electronics

DMP Electronics 1127W Manuel utilisateur

DMP Electronics

DMP Electronics 1166 Manuel utilisateur

DMP Electronics

DMP Electronics 1135INT Series Manuel utilisateur

DMP Electronics

DMP Electronics 1127W-WINT Instructions de montage

DMP Electronics

DMP Electronics 1168 Guide d'installation

DMP Electronics

DMP Electronics 1183 Series Manuel utilisateur

DMP Electronics

DMP Electronics 1126 Series Instructions de montage

DMP Electronics

DMP Electronics XTLtouch International Series Manuel utilisateur

DMP Electronics

DMP Electronics XTLplusINT Series Guide d'installation

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur

Solinst

Solinst 301 Manuel utilisateur