Dish Network WALLY Manuel utilisateur

RECEIVER SETUP GUIDE

Labeling Your Cables

Use the labels provided to complete this step. Do not remove any cables from the receiver being

replaced until Step 2.

Attach the blue label to the cable

connected to the “Satellite In”

port.

Attach the black label to the cable

connected to the“HDMI” port or

attach the orange label to the

cables connected to the RCA ports.

You will be using either an

HDMI cable or RCA cables as

your audio/video connection.

RCA

COMPOSITE

RCA

COMPOSITE

Labeling Your Cables (Cont’d)

c. Attach the yellow label to the

cable connected to the "Ethernet"

port.

Attach the gray label to the

power cord that came with

your new Wally.

2. Disconnecting Your Cables

Do not disconnect the cables from the wall or TV. Disconnect the cables from the

receiver being replaced. Only disconnect the cables at the end connected to the receiver.

Connect the Satellite In cable to

the "Satellite In" port on your

Wally.

b. Connect the HDMI cable, or RCA

cables from the TV to the

corresponding port(s) on the

replacement receiver.

RCA

COMPOSITE

RCA

COMPOSITE

3. Connecting the Cables to Your Replacement Receiver

Connecting the Cables to Your Replacement Receiver (Cont’d)

Connect the Ethernet cable to the

"Ethernet"port on the

replacement receiver.

You may not have this cable.

e. Open the panel on the side of

the new receiver and make

sure the Smart Card is

secured firmly in the slot.

Not all receivers will have a Smart Card.

If your receiver does not have a Smart

Card, go to Step 4.

Connect the power cord that

came with your Wally to the

"Power" port on your Wally.

4. Powering Your Equipment

Plug the power cord from

your Wally into a wall outlet.

Make sure your TV cord is plugged into

a wall outlet and turn on your TV.

c. Your screen should now display the

System Setup screen. If you do not

see this screen, confirm that you are

on the correct input for watching

DISH programming. Check the input

by pressing the Source/Input button

located on the side, back, or front of

your TV.

5. Acquiring a Satellite Signal

Wait while the satellite signals are

acquired. Once complete, the

system will proceed to the next step

automatically.

If you see red "Xs" in the installation

test box, make sure your "Home Video

Network" cable is connected to your

receiver and wall correctly. Then use

the arrow buttons on your remote

control to highlight "Retest

Installation," and press SELECT.

6. Downloading Your Wally Software

Wait while the System Setup wizard

downloads your Wally software. This

process will take approximately 20

minutes.

When the download is complete,

your Wally will reboot automatically.

7.Pairing Your Remote Control & Setting Your Wally Location

Press the SAT button on your remote

control to pair it to your Wally.

Using the arrows on your remote control,

highlight "Next" and press SELECT.

8. Setting Your TV Configuration

Using the arrows on your remote

control, scroll to your TV's resolution

and press SELECT. Then, highlight

"Next" and press SELECT.

Using the arrows on your remote

control, highlight "Keep" and then

press SELECT to keep your TV Display

Configuration.

Autres manuels pour WALLY

Table des matières

Autres manuels Dish Network Récepteur

Dish Network

Dish Network WALLY Manuel utilisateur

Dish Network

Dish Network DISH411 Manuel utilisateur

Dish Network

Dish Network Home Network Manuel utilisateur

Dish Network

Dish Network DISH322 Manuel utilisateur

Dish Network

Dish Network ViP 222K Manuel utilisateur

Dish Network

Dish Network 512 Manuel utilisateur

Dish Network

Dish Network DuoDVR ViP 922 Manuel utilisateur

Dish Network

Dish Network 622 guide Manuel

Dish Network

Dish Network 4K Joey Manuel utilisateur

Dish Network

Dish Network WALLY Manuel utilisateur

Dish Network

Dish Network 4K Joey Manuel utilisateur

Dish Network

Dish Network SR200 Manuel utilisateur

Dish Network

Dish Network 123698 Manuel utilisateur

Dish Network

Dish Network Hopper Manuel utilisateur

Dish Network

Dish Network HDE-8C-QAM Manuel utilisateur

Dish Network

Dish Network Receiver Manuel utilisateur

Dish Network

Dish Network 118523 Manuel utilisateur

Dish Network

Dish Network Wireless Joey Manuel utilisateur

Dish Network

Dish Network High-Definition ViP 22k Duo Receiver and... Manuel utilisateur

Dish Network

Dish Network Duo ViP 222 Manuel utilisateur

Dish Network

Dish Network 111 Series Manuel utilisateur

Dish Network

Dish Network ViP 722 Manuel utilisateur

Dish Network

Dish Network DVR Satellite System Manuel utilisateur

Dish Network

Dish Network 311 Series Manuel utilisateur

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur