Disc Makers Reflex10 Manuel utilisateur

tReflex Duplicator Manual

- 1 -

Table of Contents

Welcome Page2

Before you start Page 2

Tutorial Guide

I. Make Disc to Disc Copies Page 4

II. Make Hard Drive (HDD) to Disc Copies Page 12

III. Select the Duplication Speed Page 24

IV. Select the Master Reading Source Page 27

V. Load Master Disc onto the Hard Drive Page 30

VI. Rename Existing HDD Partition Name Page 34

VII. Delete HDD Partitions Page 37

VIII. Change HDD Partition Size Page 39

IX. Change SETUP settings Page 41

X. Audio CD Editing Page 43

XI. Account Management Feature Page 53

XII. Duplication Mode Page 58

XIII. Using AUTOCOPY Feature Page 62

Menu Overview Page 67

1.Copy Page67

2. Advanced Copy Options Page 67

3.Image Page67

4.Audio Page68

5. SETUP Page 68

6. Utilities Page 70

7. SHUTDOWN Page 72

Troubleshooting Page 73

Load Default Settings Page 75

tReflex Duplicator Manual

- 2 -

Welcome!

Thank you for buying this Disc Makers duplicator. The Reflex DVD

and CD duplicator will make it easier than ever to duplicate vast

quantities of discs. This manual contains detailed information

about using all the features in your stand-alone Reflex duplicator.

******************************************************

Before you start:

Before you start using this duplicator, please read the following to

ensure proper operation:

1. DVD Duplication Limitations:

This duplicator, it will not copy any DVD that has Copy

Protection encoded inside. DVDs you purchase or rent from a

store will be Copy Protected.

In addition to the copy protection limitation, the duplicator

will only copy a DVD-5 format (4.7GB) disc to DVD-5 format

(4.7GB) recordable DVD media. If your duplicator has double

layer capability, you can copy a DVD-9 format (8.5GB) disc to

DVD-9 format (8.5GB) recordable DVD media. You cannot

duplicate a DVD5 format disc to a DVD9 format recordable

media or vice versa.

2. Temperature Warning:

If the duplicator was stored in a location where the

temperature dropped below 32ðF (0ðC) within the past 24

hours, please leave the duplicator in a warm room with

temperatures at least 65ðF (19ðC) for 4 hours prior to

powering it on for the first time. Failure to do so may cause

irreparable harm and prevent the duplicator from functioning.

tReflex Duplicator Manual

- 3 -

3. Maintenance:

It is very important to operate and keep the duplicator in a

dust free, clean environment since dust is the number 1 killer

for CD/DVD recording devices. Failure to do so may severely

damage your duplicator. We strongly suggest you place an

Air Cleaner next to the duplicator and constantly use the Air

Duster (Can Air) to clear off any dust on the surface of the

duplicator.

Do not try to use Air Duster to clean the

duplicator while the reader/writer trays are open.

In doing so, you may inadvertently blow dust

into the recording device and damage the

recording device.

4. Proper Shutdown:

To avoid possible system failures the duplicator must be

shutdown properly. To shutdown the duplicator, use the UP or

DOWN arrow keys or the ‘Shutdown“ hot key and follow

instructions on the screen. Turning off your duplicator without

performing this function will increase the risk of damaging

your duplicator.

tReflex Duplicator Manual

- 4 -

Tutorial Guide:

I. Make Disc-to-Disc Copies

This process will copy your master disc to several blank discs

simultaneously.

When you turn on your duplicator, after it has booted up, you

should see the following signifying your duplicator is ready.

1. Make sure the Master Reading Source is set to the

READER.

It is very important to make sure that your current Master

Reading Source is the top tray in order to avoid

unnecessary error messages. To check the Master Reading

Source, please do the following:

a. Use UP or DOWN arrow buttons or “Source“ hot key

to navigate to the following screen.

b. Press “ENT“ to enter Select Source Menu and you

shall see the following:

Disc Makers .99

1. COPY

Set Up

5.2. Select Source

tReflex Duplicator Manual

- 5 -

*** The Reader Port could be indexed as 1.0.

Either 1.0 or 2.0 is fine.

Make sure it is located at the “Reader Port“. If not, then

you need to press UP or DOWN navigation button to

search for it.

c. Press “ENT“ to submit your selection.

2. Go back to “COPY“ Menu.

a. Use UP or DOWN arrow button to navigate to the

following screen:

3. Start the Copy Process.

a. Insert your master disc and your blank discs into the

corresponding tray(s) and press “ENT“ button to enter

COPY menu. You will see the duplicator mode menu like

below:

Now, you have been given two choices:

• Load and Copy

• On the Fly

Disc Makers .99

1. COPY

Duplication Mode:

Load and Copy

Reader Port 2.0

DVDR

tReflex Duplicator Manual

- 6 -

For detail information, please review “Tutorial Guide XII:

Introduction to Duplication Mode.“

Once you have decided which mode you would like to run,

press UP or DOWN arrow button until your desired mode

is displayed and press “ENT“ button to confirm.

b. Then. you will see the Counter Selection Menu like the

following:

c. The Counter Selection Menu will let you choose how many

copies you want to make for your project

You can select “No Counter“ if you prefer to copy continuously

with no interruption. (It will still count the number of copies, but it

will not notify you when to stop.) To select the “No Counter“,

simply press “ENT“ button when you see the screen above. Then

skip below and continue on to step “d“.

Or, you can select “Specify Counter“ between 1 to 9999 by

pressing the UP or DOWN navigation button to the below screen:

Then please press “ENT“ button to submit. You shall see the

screen below:

Counter:

Specify Counter

Specify Counter:

[0 ] OK?

Counter:

o Counter

tReflex Duplicator Manual

- 7 -

To specify the number of copies for your project, you need to

enter/input a 4-digit number. If you are planning to specify a

number that is less than 4 digits, please fill the leading spaces

with “0“s (any leading “0“ will be skipped). An example of that 4-

digit number could be “0234“ (Two hundred and thirty four), or

“0010“ (ten).

To enter the number, you need to use UP or DOWN button to

select the number for each digit and use “ENT“ or “ESC“ button

to move the cursor position right or left, once youíve finished,

move the cursor to “OK“ and press “ENT“. For example, if I want

to specify a counter value of 21 (twenty one). The 4-digit value

would be “0021“. To input the desired quantity, please do the

following:

Make sure the cursor is located at the first position:

i. Press “DOWN“ button consecutively until “0“ is

displayed.

ii. Press “ENT“ button once to move the cursor to the

next position.

iii. Press “DOWN“ button consecutively until “0“ is

displayed.

iv. Press “ENT“ button once to move the cursor to the

next position.

v. Press “DOWN“ button consecutively until “2“ is

displayed.

vi. Press “ENT“ button once to move the cursor to the

next position.

Specify Counter:

[X ] OK?

tReflex Duplicator Manual

- 8 -

vii. Press “DOWN“ button consecutively until “1“ is

displayed.

viii. Now, “0021“ is displayed, press “ENT“ once and the

cursor moved to “OK“.

ix. Then, press “ENT“ once to submit your counter value.

Now you shall see the following screen:

If either one of the ABOVE 2 screens are displayed

for more than 2 minutes, please check your Master

Disc or Blank Discs for quality.

d. Please allow 5-10 seconds for the duplicator to detect

your Master Disc and Blank Discs as well. After your

Master Disc and Blank Discs have been recognized, then

you shall see the following screen:

Preparing...

aiting for Blanks

Preparing...

aiting for Master

Preparing...

7 Disc Detected, Go?

*The “7” indicates there are 7 discs recognized by

the writer tray.Actual quantity may be different

depending on your machine.

tReflex Duplicator Manual

- 9 -

By default, the “Auto Start“ setting is set to

“Auto“. For example, if your duplicator has

detected 3 blank discs and didnít detect any

additional blank discs within 30 seconds, then the

duplication will start automatically.

Once the number of blank discs you inserted

matches the number of discs detected on the

screen. Then press “ENT“ (if you are not using

Auto Start or wish to speed up the process) to

confirm and the following Processing screen will

appear.

If the number of blank discs you inserted doesnít

match the number of discs detected on the

screen, please give 10-15 seconds for the

duplicator to recognize all of your blank discs

e. After 2 or 3 seconds of processing time, the following

Copy Progress Screen will appear.

Counter Specified No Counter

Processing...

Please Wait

Copying ... 4012MB

0 12%

Copying ... 4012MB

0/21 12%

- “4012MB” indicates the capacity of the

master disc.

- “12%” indicates the current progress of

the duplication.

- “0/21” indicates you have a project size

of 21 copies and you have made 0

copies so far.

- “4012MB” indicates the capacity of the

master disc.

- “12%” indicates the current progress of

the duplication.

- “0” indicates that you have made 0

copies so far.

tReflex Duplicator Manual

- 10 -

It is normal to see the progress indicator stays at 0-

10% and 100% for approximately 30 seconds for

CD duplication and up to 1 minute for DVD

duplication. That is caused by the initializing and

finalizing stage.

Once the duplication run is completed, the successful copies will

be ejected and you shall see the following screen:

Next, refill more blank media to continue making more

copies, or you can press “ESC“ to terminate your project

and go back to the main menu.

If youíve specified a counter value for your project and

your project is completed, you shall see the following

screen:

If you see above message, you can press “ENT“ to go

back to main menu.

21 Disc Copie

Press OK to Finish

PASS 7 FAIL 0( 7)

aiting for Blanks

- “PASS 7” indicates that you’ve

just made 7 successful copies.

- “FAIL 0” indicates that you

have no failure in this run.

- “7” indicates that you’ve

successfully copied 7 copies so

far.

tReflex Duplicator Manual

- 11 -

If you enabled the counter and the number of

discs you have inserted is more than what you

requested, you will receive a message regarding

you have inserted more discs than what you need.

You can continue to copy or you can eject the

extras.

If you happen to have any failed discs (bad copy),

the failed disc(s) will not be ejected automatically.

You need to manually eject them and throw them

away if they are write once recordable disc(s).

tReflex Duplicator Manual

- 12 -

Tutorial Guide:

II. Make Hard Drive(HDD)-to-Disc Copies

Copying from the Hard Drive is the best way to make copies!

There are 3 benefits to copying from the Hard Drive:

i. Performance ñ Duplicating from the Hard Drive will be

able to boost the DVD duplication speed.

ii. Stability ñ Duplicating from Hard Drive will stabilize the

duplication process compared to the Disc to Disc

process.

iii. Convenience ñ With your master discs stored inside the

Hard Drive, you can have access to each one easily.

There is no need to carry your master discs; they are all

stored inside the duplicator.

Your built-in Hard Drive will be divided into a number of

partitions. Each partition will hold ONE and ONLY ONE

master disc regardless of the capacity of your master disc.

The number of partitions is determined by dividing your Hard

Driveís total capacity by 1GB for CD format, 5GB for DVD-5

format or 9GB for DVD-9 format (Double Layer) and

subtracting one partition for system use.

The following steps will show you how to load your master

disc into the installed Hard Drive as a disc image and copy the

stored disc image into several blank discs. This process is

recommended for large volume production.

tReflex Duplicator Manual

- 13 -

How to make copies from the Hard Drive?

When you turn on your duplicator, after it has booted up, you

should see the following signifying your duplicator is ready.

1. Make sure the Master Reading Source is set to the Hard

Drive.

It is very important to make sure the Master Reading Source

is set to the Hard Drive in order to avoid unnecessary error

messages. To check the Master Reading Source, please do

the following:

Use UP or DOWN arrow button to navigate to the following

screen.

a.Press “ENT“ to enter Select Source Menu and you shall

see the following:

Make sure it is located at “Hard Drive“. If not, then you

need to press UP or DOWN navigation button to search

for it.

b. Press “ENT“ to submit your selection. After your

selection has been submitted, you will see the following:

Hard Drive Port 0

DC WD400EB-75CPF0

Disc Makers .99

1. COPY

Setup

5.2 Select Source

tReflex Duplicator Manual

- 14 -

2. Load your master disc onto the Hard Drive. If you have

already loaded your master disc onto the Hard Drive, then

you can skip step 2 and go to step 3.

a. Use UP or DOWN arrow button to navigate to the

following screen.

Press “ENT“ to enter Hard Drive Setup Menu and you shall see

the following:

b. Press “ENT“ to enter Load Partition Menu and you

shall see the following:

c. Now, you have a choice to load your master disc into a

new (empty) partition or overwrite one of the existing

partitions. Press UP or DOWN arrow button to select your

Setup

5.2 Select Source

Image

3.2 Load Partition

Load Partition [ 1/ 8]

Load->New Partition

*The “1” indicates the number of partitions

you’ve already loaded into the Hard

Drive . (Includes the Reserve Partition)

*The “8” indicates the total number of partitions

you can load to the Hard Drive.

tReflex Duplicator Manual

- 15 -

partition and press “ENT“ to submit. You will see the

following:

d. Name the partition you are about to load into the Hard

Drive. To enter the name, you need to use the UP or

DOWN buttons to select the character and use “ENT“ or

“ESC“ button to move the cursor position and once

youíve finished, move the cursor to “OK“ and press

“ENT“. For example, if you want to name the partition for

your master disc as “FUN“. Then do the following:

Make sure the cursor is located at the first position:

i. Press “DOWN“ button consecutively until “F“

is displayed.

ii. Press “ENT“ button once to move the cursor to

the next position.

iii. Press “DOWN“ button consecutively until “U“

is displayed.

iv. Press “ENT“ button once to move the cursor to

the next position.

v. Press “DOWN“ button consecutively until “N“

is displayed.

vi. Press “ENT“ button once to move the cursor to

the next position.

Edit Partition Name

[ ] OK?

Edit Partition Name

[x ] OK?

tReflex Duplicator Manual

- 16 -

vii. The name “FUN“ will be displayed. Press

“ENT“ consecutively until the cursor is moved

to “OK“.

viii. Then, press “ENT“ once to submit your name

selection.

e. Now you shall see the following confirmation screen:

f. Press “ENT“ button to confirm. Once your master disc has

been recognized. The loading progress indicator will be

displayed and you shall see the following

g. Once your master disc has been loaded completely, you

shall see the following:

Then, you can press “ENT“ button to go back to the Hard

Drive Setup Menu.

3. Go back to “COPY“ Menu.

Load Partition?

[FUN ], OK?

Load Partition OK!

Press OK to Continue

Loading ... FUN

1% 123MB loaded

*The “123MB” indicates the amount of data has

been loaded to the Hard Drive.

tReflex Duplicator Manual

- 17 -

a. Press “ESC“ button to go back to the main menu. You

shall see the following:

b. Use UP or DOWN arrow button to navigate to the

following screen.

4. Start the Copy Process.

a. Now, please insert your blank discs into the writer trays

(make sure the Reader Tray is empty) and press “ENT“

button to enter COPY menu. You will be asked to

choose which hard drive partition to copy from:

b. Choose the desired partition to copy from and press

“ENT“ button to submit your selection. Then you shall

see the following Counter Selection Menu:

Choose Partition

2->[FUN ]DVD

Counter:

o Counter

Image

3.2 Load Partition

Disc Makers .99

1. COPY

tReflex Duplicator Manual

- 18 -

c. The Counter Selection Menu will let you to choose how

many copies you want to make for your project. This

Counter Selection feature will allow the duplicator to

count the number of copies youíve made and prompt

you when the desired number of copies has been made.

You can select “No Counter“ if you prefer to copy continuously

with no interruption. (It will still count the number of copies, but it

will not notify you when to stop.) To select the “No Counter“,

simply press “ENT“ button when you see the screen above. Then

skip below and continue on to step “d“.

Or, you can select “Specify Counter“ between 1 to 9999 by

pressing the UP or DOWN navigation button to the below screen:

Then please press “ENT“ button to submit. You shall see the

screen below:

To specify the number of copies for your project, you need to

enter/input a 4-digit number. If you are planning to specify a

number that is less than 4 digits, please fill the leading spaces

with “0“s (any leading “0“ will be skipped). An example of that 4-

digit number could be “0234“ (Two hundred and thirty four), or

“0010“ (ten). Remember, the beginning “0“s are skipped,

therefore “0010“ means “10“, which is the number 10.

Counter:

Specify Counter

Specify Counter:

[0 ] OK?

tReflex Duplicator Manual

- 19 -

To enter the number, you need to use UP or DOWN button to

select the number for each digit and use “ENT“ or “ESC“ button

to move the cursor position right or left, once youíve finished,

move the cursor to “OK“ and press “ENT“. For example, if I want

to specify a counter value of 21 (twenty one). The 4-digit value

would be “0021“. To input the desired quantity, please do the

following:

Make sure the cursor is located at the first position:

i. Press “DOWN“ button consecutively until “0“ is

displayed.

ii. Press “ENT“ button once to move the cursor to the

next position.

iii. Press “DOWN“ button consecutively until “0“ is

displayed.

iv. Press “ENT“ button once to move the cursor to the

next position.

v. Press “DOWN“ button consecutively until “2“ is

displayed.

vi. Press “ENT“ button once to move the cursor to the

next position.

vii. Press “DOWN“ button consecutively until “1“ is

displayed.

viii. Now, we have “0021“ displayed and then, press

Specify Counter:

[X ] OK?

tReflex Duplicator Manual

- 20 -

“ENT“ once and the cursor is now moved to “OK“.

ix. Then, press “ENT“ once to submit your counter value.

Now you shall see following screen:

If the ABOVE screen is displayed for more than 2

minutes, please check your Blank Discs for

quality.

d. Please allow 5-10 seconds for the duplicator to detect

your Hard Drive partition and Blank Discs as well. After

your Hard Drive partition and Blank Discs have been

recognized, then you shall see the following screen:

By default, the “Auto Start“ setting is set to “Auto“.

For example, if your duplicator has detected 3 blank

discs and didnít detect any additional blank discs for

30 seconds, then the duplication will be started

automatically.

Preparing...

aiting for Blanks

Preparing...

7 Disc Detected, Go?

*The “7” indicates there are 7 discs that were

recognized by the recording tray. Actual quantity

may be different depend on your machine.

Autres manuels pour Reflex10

Table des matières

Autres manuels Disc Makers Matériel informatique

Disc Makers

Disc Makers Reflex4 Manuel

Disc Makers

Disc Makers ReflexPro4 Manuel utilisateur

Disc Makers

Disc Makers Elite2 Manuel utilisateur

Disc Makers

Disc Makers Elite2 Instructions d'installation et d'entretien

Disc Makers

Disc Makers 1.1 Manuel utilisateur

Disc Makers

Disc Makers Reflex4 Manuel utilisateur

Disc Makers

Disc Makers Reflex1 Manuel utilisateur

Disc Makers

Disc Makers Elite2 Manuel utilisateur

Disc Makers

Disc Makers Elite2 Manuel utilisateur

Disc Makers

Disc Makers Forte Manuel utilisateur

Disc Makers

Disc Makers Reflex1 Manuel utilisateur

Disc Makers

Disc Makers Reflex1 Manuel utilisateur

Disc Makers

Disc Makers ReflexPro4 Manuel utilisateur

Disc Makers

Disc Makers Reflex1 Manuel utilisateur

Disc Makers

Disc Makers ElitePro Manuel utilisateur

Disc Makers

Disc Makers Reflex10 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur