Directed Electronics 7111A Manuel utilisateur

Congratulations

Congratulations on the purchase of your state-of-the-art keyless entry

and remote start system. Reading this Owner’s Guide prior to using

your system will help maximize the use of your system and its many

features. For more information please visit us online at:

www.automatecarsecurity.com.

For any additional questions please contact your authorized Directed

dealer or Directed at 1-800-753-0600. Additional support is also

available at:

http://support.directed.com

What's included

• Two 1-button remote controls (P/N 7111A)

• Your warranty registration card

• Quick reference card

• This owner's guide

Warranty

Card

Owner’s

Guide

Quick

Reference Card

Important information

Government Regulations and Safety information

Read the Government Regulations and Warning! Safety

First sections of this manual prior to operating this system.

Warning!

Failure to heed this information can result in

death, personal injury or property damage and may also

result in the illegal use of the system beyond its intended

purpose.

Your warranty

Your system comes with a warranty. Please make sure you receive

the warranty registration card and proof of purchase from your dealer

indicating the product was installed by an authorized Directed dealer.

Your product warranty must be validated within 10 days of purchase.

You can validate online at:

www.prodregister.com/automate

or com-

plete and return the warranty registration card.

Replacement Remote controls

If additional remote controls are desired, please see your authorized

dealer or visit us at

www.directedstore.com

to order. Your 1-way re-

placement part number is 7111A.

Contents

Congratulations .................................................................................................i

What's included .............................................................................................i

Important information ........................................................................................ii

Your warranty...........................................................................................ii

Replacement Remote controls .....................................................................ii

Getting Started .................................................................................................2

System maintenance ..................................................................................2

Battery replacement ..................................................................................2

Using the system .............................................................................................3

Unlocking ................................................................................................3

Car finder ................................................................................................3

Remote Start .............................................................................................4

Valet Take-Over ........................................................................................6

Government Regulations ....................................................................................7

Warning! Safety first .........................................................................................8

Caution ...................................................................................................9

Español .........................................................................................................12

Getting Started

System maintenance

The system requires no speciﬁc maintenance beyond battery replace-

ment for the remote controls. Your remote is powered by a coin cell

battery (3V CR2032) that lasts approximately one year under normal

use. When the battery begins to weaken operating range is reduced

and the LED on the remote dims.

Battery replacement

Locate the small slot on the side of the remote control. Insert a small

slotted screwdriver or equivalent tool into slot and pry the case apart.

Replace battery while verifying the correct polarity and then snap case

together.

Using the system

Unlocking

Only after the vehicle is remotely started via the transmitter, press and

release the transmitter button for 1 second to unlock the vehicle’s doors.

The parking lights ﬂash and the horn honks twice to conﬁrm unlock.

Important: Horn honk is an optional feature.

Car ﬁnder

Car ﬁnder allows you to locate your vehicle, by having the system ﬂash

the parking lights.

Before the vehicle is remotely started via the transmitter, press and

hold the transmitter button for 3 seconds to activate the car ﬁnder

function. The parking lights ﬂash 5 times slowly.

Remote Start

This feature allows you to remotely start and run your vehicle for a

pro gram ma ble period of time. This makes it possible to warm up the

engine, and adjust the interior tem per a ture of the ve hi cle with the cli-

mate control system. If interior heating or cooling is desired, the climate

controls must be preset, and the fan blower must be set to the desired

level prior to remote starting the vehicle.

Sat mode,

bank selector

AUDIO

PWR

1 2

REW FF

PLAY/PROG NR

3 4 5 6

DISC- DISC+

11:53

XM1-1 CH-001

VOL

SCAN SOUND

AM/FM

CD/AUX

SAT

RADIO

SEEK

SKIP

RPT

DISP -

MODE

A.SEL

RDM

TUNE

AUTO

OFF

DUAL

A/C MODE

Channel control

Category

Control

Text selector.

Hold for 10sec to toggle

channel or category

tune modes.

Toggles

Scan mode

Bank and

present

indicator

Channel

and text

indicator

Preset 1-6.

Hold until beep to

save to a preset.

CATEGORY

Tune mode

indicator

MODE

DUAL

OFF

AUTO

MAP/

GUIDE MENU SETUP

INFO ZOOM CANCEL AUDIO

AUTO

MODE

A/C

LOAD

DISC

TAPE AM/FM DISP

MODE

SCAN RPT A.SEL/RDM - SEEK +

123 4 56

DISC- DISC+

VOL

PWR

PUSH

TUNE

SOUND

PUSH

XM1-1

VOL

CHANNEL

CATEGORY

NAME

TITLE

MODE SCAN SOUND

001 - HITS1

POP

MUSIC NAME

MUSIC TITLE

Channel control

Category

Control

001 014 018

040 065 115

Toggles between

channel and

category modes

Bank and

present

indicator

Upper display

text mode

selector

Sat mode

and bank

selector

Preset 1-6.

Press until

beep to save

to a preset.

Channel and text

Indicator fields

Toggles

Scan mode

Tune mode

indicator

ANTENNA

SC OUTPUT

Sirius-Ready, SAT Radio Ready or select OEM headunits with optional Honda Bus Compatible Translator

Headunit bus cable SiriusConnect Cable

HON-SC1

Honda Bus

Compatible

Translator

Warning!

(1) Never remote start your vehicle when

the keys are in the ignition, except when performing

Valet Take-Over, and (2) Never start the vehicle if it

is not in PARK or NEUTRAL

To remote start the vehicle:

• Press the button on the remote control for 1 second.

• The parking lights ﬂash to conﬁrm that the vehicle is attempting to

start. In gasoline vehicles, the engine will start 4 seconds after the

parking lights ﬂash. In diesel vehicles, the engine will start when

the WAIT-TO-START timer has expired.

• Once the vehicle has started, it will run for the pre- pro gram med

period of time (12, 24, or 60 minutes) or until a shutdown input

is trig gered.

Sat mode,

bank selector

AUDIO

PWR

1 2

REW FF

PLAY/PROG NR

3 4 5 6

DISC- DISC+

11:53

XM1-1 CH-001

VOL

SCAN SOUND

AM/FM

CD/AUX

SAT

RADIO

SEEK

SKIP

RPT

DISP -

MODE

A.SEL

RDM

TUNE

AUTO

OFF

DUAL

A/C MODE

Channel control

Category

Control

Text selector.

Hold for 10sec to toggle

channel or category

tune modes.

Toggles

Scan mode

Bank and

present

indicator

Channel

and text

indicator

Preset 1-6.

Hold until beep to

save to a preset.

CATEGORY

Tune mode

indicator

MODE

DUAL

OFF

AUTO

MAP/

GUIDE MENU SETUP

INFO ZOOM CANCEL AUDIO

AUTO

MODE

A/C

LOAD

DISC

TAPE AM/FM DISP

MODE

SCAN RPT A.SEL/RDM - SEEK +

123 4 56

DISC- DISC+

VOL

PWR

PUSH

TUNE

SOUND

PUSH

XM1-1

VOL

CHANNEL

CATEGORY

NAME

TITLE

MODE SCAN SOUND

001 - HITS1

POP

MUSIC NAME

MUSIC TITLE

Channel control

Category

Control

001 014 018

040 065 115

Toggles between

channel and

category modes

Bank and

present

indicator

Upper display

text mode

selector

Sat mode

and bank

selector

Preset 1-6.

Press until

beep to save

to a preset.

Channel and text

Indicator fields

Toggles

Scan mode

Tune mode

indicator

ANTENNA

SC OUTPUT

Sirius-Ready, SAT Radio Ready or select OEM headunits with optional Honda Bus Compatible Translator

Headunit bus cable SiriusConnect Cable

HON-SC1

Honda Bus

Compatible

Translator

Warning!

It is unsafe to operate a vehicle’s motor in a

garage or other closed off area. Breathing the ex haust

from the vehicle is hazardous to your health. Never

activate the remote start in an enclosed space.

When you are ready to drive the vehicle:

1. Insert the ignition key and turn it to the ON (not the START)

po sition.

2. Press the brake pedal. The remote start system shuts down and the

engine continues to run because the ignition has been turned on.

Note:

If the brake pedal is pressed before the key is in the ON position,

the engine will shut down.

While the vehicle is running during remote start operation, the system

monitors the ve hi cle and automatically shuts down the engine if it receives

any of the following shut-down inputs:

• The brake pedal is pressed.

• The hood is opened.

• The shutdown toggle switch is put into the OFF position.

• The pre-programmed run time has elapsed.

• Remote control button is pressed and held for 3 seconds.

Valet Take-Over

The Valet Take-Over feature allows the vehicle to remain running after

the key has been removed from the ignition. This feature is useful for

occasions when you wish to exit and lock the vehicle for short periods

of time, but would like to leave the engine running and the climate

controls on.

To perform Valet Take-Over:

1. Before turning off the engine, press and release the single button

on the remote.

2. Turn the ignition key to the OFF position. The engine will stay run-

ning until the pre- pro gram med time has elapsed or a shutdown

input is received. (See the previous Remote Start section for a

complete list of shut-down inputs.)

This feature will not work if the brake pedal is being pressed.

Government Regulations

This device complies with Part 15 of FCC rules. Operation is subject to the fol-

lowing two conditions: (1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that

may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential instal-

lation. This equipment generates and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television, which can be determined by

turning the equipment OFF and ON, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

This device complies with the Industry Canada Radio Standards Speciﬁcation

RSS 210. Its use is authorized only on a no-interference, no-protection basis; in

other words, this device must not be used if it is determined that it causes harm-

ful interference to services authorized by IC. In addition, the user of this device

must accept any radio interference that may be received, even if this interference

could affect the operation of the device.

Warning:

Changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate this device.

Warning! Safety ﬁrst

The following safety warnings must be observed at all times:

Due to the complexity of this system, installation of this product must only be

performed by an authorized Directed dealer.

When properly installed, this system can start the vehicle via a command signal

from the remote control. Therefore, never operate the system in an enclosed area

or partially enclosed area without ventilation (such as a garage). When parking

in an enclosed or partially enclosed area or when having the vehicle serviced,

the remote start system must be disabled using the installed toggle switch. It is

the user’s sole responsibility to properly handle and keep out of reach from chil-

dren all remote control devices to assure that the system does not unintentionally

remote start the vehicle. THE USER MUST INSTALL A CARBON MONOXIDE

DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.

ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED

OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES

REMAIN CLOSED. These precautions are the sole responsibility of the user.

Use of this product in a manner contrary to its intended mode of operation may

result in property damage, personal injury, or death. (1) Never remotely start the

vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with

the keys in the ignition. The user must also have the neutral safety feature of the

vehicle periodically checked, wherein the vehicle must not remotely start while

the car is in gear. This testing should be performed by an authorized Directed

dealer in accordance with the Safety Check outlined in the product installation

guide. If the vehicle starts in gear, cease remote start operation immediately and

consult with the authorized Directed dealer to ﬁx the problem.

After the remote start module has been installed, contact your authorized dealer

to have him or her test the remote start module by performing the Safety Check

outlined in the product installation guide. If the vehicle starts when performing

Table des matières

Autres manuels Directed Electronics Démarreur à distance

Directed Electronics

Directed Electronics PS-3655E-FM Manuel utilisateur

Directed Electronics

Directed Electronics Python G4203P Manuel utilisateur

Directed Electronics

Directed Electronics AutoCommand 40027 Manuel utilisateur

Directed Electronics

Directed Electronics 560T Manuel utilisateur

Directed Electronics

Directed Electronics Viper Manuel utilisateur

Directed Electronics

Directed Electronics 553 Manuel utilisateur

Directed Electronics

Directed Electronics Smart start Manuel utilisateur

Directed Electronics

Directed Electronics AS-2371TW-FM Manuel utilisateur

Directed Electronics

Directed Electronics 20.7 Manuel utilisateur

Directed Electronics

Directed Electronics Hornet 564T Manuel utilisateur

Directed Electronics

Directed Electronics READY REMOTE 24923 Manuel utilisateur

Directed Electronics

Directed Electronics AVITAL 4003 Manuel utilisateur

Directed Electronics

Directed Electronics Viper 5501 Manuel utilisateur

Directed Electronics

Directed Electronics SmartStart 5000-series Manuel utilisateur

Directed Electronics

Directed Electronics AM6 Manuel utilisateur

Directed Electronics

Directed Electronics PS-4461TWE-FM Manuel utilisateur

Directed Electronics

Directed Electronics Avital 4113 Manuel utilisateur

Directed Electronics

Directed Electronics 5301 Manuel utilisateur

Directed Electronics

Directed Electronics Python 951 Manuel utilisateur

Directed Electronics

Directed Electronics Cyber 110XV Manuel utilisateur

Directed Electronics

Directed Electronics 991 Manuel utilisateur

Directed Electronics

Directed Electronics Valet 561T Manuel utilisateur

Directed Electronics

Directed Electronics AutoCommand 28624TN Guide de démarrage rapide

Directed Electronics

Directed Electronics 4103 Series Manuel utilisateur

Manuels Démarreur à distance populaires d'autres marques

AstroStart

AstroStart 803U Manuel utilisateur

Durite

Durite 0-649-20 Manuel

EINHELL

EINHELL BT-PS 1000 Manuel

Linear

Linear ACCESS AK-21 Caractéristiques techniques

Soundstream

Soundstream TARANTULA RS.2 Manuel utilisateur

Jaycar Electronics

Jaycar Electronics MB3752 Manuel utilisateur

Ultra Start

Ultra Start 72 Series Manuel utilisateur

ADS

ADS FLASHLOGIC FLRSVW1 Manuel utilisateur

Selecta

Selecta JS012 Manuel utilisateur

Black Widow Security

Black Widow Security BW RAS 400 Manuel utilisateur

Vector

Vector Power City DK080706 Supplément

Code Alarm

Code Alarm CA-535 Manuel utilisateur

Ozito

Ozito OJS-800 Manuel utilisateur

Profi-Partner

Profi-Partner 46387 Manuel utilisateur

EZ STARTER

EZ STARTER EZ-45 Manuel utilisateur

Viper

Viper 4204 Manuel utilisateur

Essex Electronics

Essex Electronics KE-1701 Manuel utilisateur

EINHELL

EINHELL EGS 3600 Manuel