Directed Electronics 2102T Manuel utilisateur

This product is intended for installation by a professional

installer only! Attempts to install this product by a person other than a

trained professional may result in severe damage to a vehicle’s electrical

system and components.

N2102T 2012-07

Directed Passive Keyless Entry (PKE)

Model 2102T

Installation Guide

Contents

Antenna Mounting and Installation Points��5

Vehicle Category Installation Specification ��5

Installation Type Selection ��6

Installation diagram��7

Wiring connections ��19

D2D port (H2), 4-pin black connector ��19

Feature Programming ��20

Entering feature programming routine ��20

Changing feature options ��20

Accessing another feature��20

Exiting feature programming ��20

Features and Options List��21

SmartLock feature��22

Remote pairing ��23

Pairing the FOB to the PKE module:��23

Pairing the PKE system to the remote starter module: ��23

Factory reset��23

Diagnostics ��23

Warning! safety ﬁrst

The following safety warnings must be observed at all times:

Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.

When properly installed, this system can lock and unlock your doors and also arm and disarm your Directed security system

when the key fob is in and out of range.

The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:

Never use a test light or logic probe when installing this unit. Always use a multimeter.

Antenna Mounting and Installation Points

In order to maximize range, the following antenna mounting options should be discussed with the customer to better suit their

needs.

Warning

• Do not directly mount the antenna on any metallic surface, this may signiﬁcally decrease the range.

• To insure consistent operation, secure the antenna and make sure they will not move or dangle.

• Antennas are fragile, they can break easily. Make sure they are mounted on a solid (non ﬂexible) part.

Recommended Antenna Mounting Locations

The recommended antenna mounting locations are for reference only. It is still required that you perform the actual range test

when installing the antenna to ensure that the range is satisfactory. You may require to relocate the antennas to different areas

around the recommended locations until maximum range is achieved.

Option 1 Option 2 Option 3

Antennas

Since this is a directional antenna,

range will be aected by antenna

placement/mounting

Horizontal rangeVertical range

Option 4

Note: An optionnal 12-foot antenna (part# SANT-PKE12) can be installed to increase the active zone coverage. When a

third antenna is installed, feature 4, option 2 must be enable through the "Features and Options List" section on page 21.

Vehicle Category Installation Speciﬁcation

Sub Compact, Compact & Sedan:

For optimal performance, install the 18-foot antenna in the headliner or below the rear deck.

Note: Installation in the trunk will greatly affect and reduce range and overall system performance.

Minivan & SUV:

To maximize range in the rear of the vehicle, install the 18-foot antenna in the headliner.

Pickup (with cab) & Cargo:

To maximize range in the rear of the vehicle, install the 18-foot antenna in the bumper, behind the license plate.

Pickup (without cab):

Suggested Installation: Option 3. Antennas should be mounted on the driver and passenger side since the tailgate does not

require to be controlled.

Convertible:

Install 8-foot antenna in windshield pillar on driver side and the 18-feet antenna behind the rear seats.

Note: On vehicle with ﬁberglass bodies or convertibles, the range will be signiﬁcantly increased.

Installation Type Selection

Choosing the right installation type according to the device you install.

Corresponding installation type according to what device you are installing Page

Type 1 - PKE Standalone page 7

Type 2a - PKE + Xpresskit Bypass + AutoStart or AstroStart or Viper/Python/Clifford Directed

Remote Starter (with 4-pin antenna connector) page 8

Type 2b - PKE + Xpresskit Bypass + Viper/Python/Clifford Directed Remote Starter (with 6-pin

antenna connector) page 9

Type 3a - PKE + Xpresskit Bypass + DIRECTED SmartStart + Autostart or Astrostart Directed Remote

Starter (with 4-pin antenna connector) page 10

Type 3b - PKE + Xpresskit Bypass + DIRECTED SmartStart + Viper/Python/Clifford Directed Remote

Starter (with 6-pin antenna connector) page 11

Type 3c - PKE + Xpresskit Bypass + DIRECTED SmartStart + Viper/Python/Clifford Directed Remote

Starter (with 4-pin antenna connector) page 12

Type 4 - PKE + 4x10/5x10 page 13

Type 5 - PKE + Xpresskit Bypass page 14

Type 6 - PKE + DIRECTED SmartStart + 4x10/5x10 page 15

Type 7 - PKE + Xpresskit Bypass - Remote Start Ready (RSR) + DIRECTED SmartStart page 16

Type 8 - PKE + Xpresskit Bypass - Range Extender (RXT) + XL202 page 17

Type 9 - PKE + AutoStart or AstroStart or Viper/Python/Clifford Directed Remote Starter (with 4pin

antenna connector) page 18

Installation diagram

Type 1 - PKE Standalone

6 Green 6 Black

4 Red2 Black

2 Black

2 Red10 Black

LED

PKE

Prog. Button

(-) Unlock Output: Blue: 2

(-) Lock Output: Green: 1

(+) Door Sense Input: White/Purple: 4**

(-) Starter Kill Output: White/Black: 6

(-) Parking Light Output: White/Pink: 7

(-) Door Sense Input: Blue/White: 10**

(-) Unlock

(-) Lock

(+) Brake

(+) Starter

(+) Ignition

(-) Parking Light

(-) Door Sense**

Antenna (8 feet)

Antenna (18 feet)

86 85

87a

(+) Brake Input: Purple/Black: 5

(+) Door Sense**

Starter Disable:

This connection is

optional and ad-

ditional parts are

sold separately.

Refer to the

Antenna Location

and Installation Points

section on page 5 for

more information.

(-) Horn Output: Red/White: 3

(-) Horn

This toggle switch will

bypass the starter disable.

(-) Ground: Black: 2

RX: Blue: 1

(+) 12v: Red: 4

D2D Y CABLE

Cut the 4-wire red connector of D2D Y-cable and connect

12v and Ground wires to the corresponding wires of the DIRECTED SmartStartTM cable.

Not Used

Ground: Black

(+)12v: Red

Ground: Black

(+)12v: Red

*Sold separately.

**Door sense: The polarity of the door sense in the vehicle will determine which wire to connect

from the PKE to the DIRECTED Remote Starter.

2 White

Optional

Antenna (12 feet)*

(Part# SANT-PKE12)

Type 2a - PKE + Xpresskit Bypass + AutoStart or AstroStart or Viper/Python/Clifford

Directed Remote Starter (with 4-pin antenna connector)

Note: 8210 Antenna Universal Adapter is required and sold separately.

These wires are not required in D2D mode.

4 Red

(-) Door Status Output

(+) Brake Output

(+) Brake Input: Purple/Black: 5

(-) Starter Kill: White/Black: 6

(-) Door Sense Input: Blue/White: 10***

(+) Brake Input

(-) Door Sense Input***

Remote

Starter*

8210 Main

Universal

Adaptor*:

Refer to the

8210 guide.

Regular Remote

Start Connections

To The Vehicle

4 White

(+) 12v: Red: 4

(-) Ground: Black: 2

RX: Green: 3

TX: Blue: 1

RX: Blue: 1

TX: Green: 3

(-) Ground: Black: 2

(+) 12v: Red: 4

(-) Ground: Black: 2

RX: Blue: 1

(+) 12v: Red: 4

Xpresskit

Interface Module*

D2D Y CABLE

6 Green 6 Black

4 Red2 Black 2 Red10 Black

LED

PKE

Prog. Button

Antenna** 8210*

Antenna Harness**

8210*

*Sold separately.

**Antenna & Antenna harness are sold with your Remote Starter kit.

*** Door sense: The polarity of the door sense in the vehicle will determine which wire to connect

from the PKE to the DIRECTED Remote Starter.

D2D Port Antenna

D2D Port

(-) Horn Output: Red/White: 3

Antenna (8 feet)

Antenna (18 feet)

Refer to the

Antenna Location

and Installation Points

section on page 5 for

more information.

(+) Ignition Output

86 85

87a

(+) Starter Wire

4 wires red

connector

4 wires white

connector

3 wires red

connector

Starter Disable:

This connection is

optional and ad-

ditional parts are

sold separately.

This toggle switch will

bypass the starter disable.

(+) Door Sense Input: White/Purple: 4***

(+) Door Sense Input***

2 White

Optional

Antenna (12 feet)*

(Part# SANT-PKE12)

Type 2b - PKE + Xpresskit Bypass + Viper/Python/Clifford Directed Remote Starter

(with 6-pin antenna connector)

These wires are not required in D2D mode.

4 Red

(-) Door Status Output

(+) Brake Output

(+) Brake Input: Purple/Black: 5

(-) Starter Kill: White/Black: 6

(-) Door Sense Input: Blue/White: 10****

(+) Brake Input

(+) Ignition Output

(-) Door Sense Input****

Remote

Starter*

4 White

(-) Ground: Black: 2

RX: Blue: 1

(+) 12v: Red: 4

Xpresskit

Interface Module*

(+) Door Sense Input: White/Purple: 4****

(+) Door Sense Input****

D2D Y CABLE

6 Green 6 Black

4 Red2 Black 2 Red10 Black

LED

PKE

Prog. Button

Antenna** Antenna Harness**

*Sold separately.

**Antenna & Antenna harness are sold with your Remote Starter kit.

***10-foot Antenna Cable is included in the PKE kit.

**** Door sense: The polarity of the door sense in the vehicle will determine which wire to connect

from the PKE to the DIRECTED Remote Starter.

D2D Port Antenna

10-foot Antenna Cable***

D2D Port

(+) 12v: Red: 4

(-) Ground: Black: 2

RX: Green: 3

TX: Blue: 1

RX: Blue: 1

TX: Green: 3

(-) Ground: Black: 2

(+) 12v: Red: 4

86 85

87a

(+) Starter Wire

Antenna (8 feet)

Antenna (18 feet)

Refer to the

Antenna Location

and Installation Points

section on page 5 for

more information.

Regular Remote

Start Connections

To The Vehicle

(-) Horn Output: Red/White: 3

4 wires red

connector

4 wires white

connector

3 wires red

connector

Starter Disable:

This connection is

optional and ad-

ditional parts are

sold separately.

This toggle switch will

bypass the starter disable.

Optional

Antenna (12 feet)*

(Part# SANT-PKE12)

2 White

Type 3a - PKE + Xpresskit Bypass + DIRECTED SmartStart + Autostart or Astrostart

Directed Remote Starter (with 4-pin antenna connector)

Note: 8210 Antenna Universal Adapter is required and sold separately.

These wires are not required in D2D mode.

(-) Door Status Output

(+) Brake Output

(+) Brake Input: Purple/Black: 5

(-) Starter Kill: White/Black: 6

(-) Door Sense Input: Blue/White: 10****

(+) Brake Input

(-) Door Sense Input****

Regular Remote

Start Connections

To The Vehicle

4 White

(-) Ground: Black: 2

RX: Blue: 1

(+) 12v: Red: 4

Xpresskit

Interface Module*

(+) Door Sense Input: White/Purple: 4****

(+) Door Sense Input****

LED

CABLE***

6 Green 6 Black

4 Red

2 Black

2 Red10 Black

LED

PKE

Prog. Button

The connector depends

of the installed bypass.

Refer to the DIRECTED SmartStart

install guide for proper connection.

4 Red

Autostart RS*

Astrostart RS*

The remote starter model will

determine which connector to use.

Refer to the DIRECTED SmartStart

install guide for proper connection.

DIRECTED

SmartStart

*Sold separately.

**Antenna & Antenna harness are sold with your Remote Starter kit.

***DIRECTED SmartStart

cable is sold with your DIRECTED SmartStart

system.

**** Door sense: The polarity of the door sense in the vehicle will determine which wire

to connect from the PKE to the DIRECTED Remote Starter.

D2D Port Antenna

(+) 12v: Red: 4

(-) Ground: Black: 2

RX: Green: 3

TX: Blue: 1

RX: Blue: 1

TX: Green: 3

(-) Ground: Black: 2

(+) 12v: Red: 4

(-) Horn Output: Red/White: 3

Antenna (8 feet)

Antenna (18 feet)

Refer to the

Antenna Location

and Installation Points

section on page 5 for

more information.

D2D Y CABLE

Cut the 4-wire red connector of D2D Y-cable and connect RX (Blue),

12v and Ground wires to the corresponding wires of the DIRECTED SmartStart

cable.

Not Used

RX: Blue

Ground: Black

(+)12v: Red

(+) Ignition Output

86 85

87a

(+) Starter Wire

Starter Disable:

This connection is

optional and ad-

ditional parts are

sold separately.

3 wires red

connector

8210 Main

Universal

Adaptor*: Refer

to the 8210 guide.

Antenna** 8210*

Antenna Harness**

8210*

This toggle switch will

bypass the starter disable.

2 White

Optional

Antenna (12 feet)*

(Part# SANT-PKE12)

Table des matières

Autres manuels Directed Electronics Alarme de voiture

Directed Electronics

Directed Electronics IntelliGuard 7000 Manuel utilisateur

Directed Electronics

Directed Electronics 4103 Series Manuel utilisateur

Directed Electronics

Directed Electronics Clifford 12.2X Manuel utilisateur

Directed Electronics

Directed Electronics 4400 Manuel utilisateur

Directed Electronics

Directed Electronics Model 3000 ESP Manuel utilisateur

Directed Electronics

Directed Electronics Concept 650 Manuel utilisateur

Directed Electronics

Directed Electronics Concept 650 Manuel utilisateur

Directed Electronics

Directed Electronics 556U Manuel utilisateur

Directed Electronics

Directed Electronics Hornet 742T Manuel utilisateur

Directed Electronics

Directed Electronics Arrow 5 Manuel utilisateur

Directed Electronics

Directed Electronics VIPER 5701 Manuel utilisateur

Directed Electronics

Directed Electronics AdvantGuard 5 Manuel utilisateur

Directed Electronics

Directed Electronics K10 Manuel utilisateur

Directed Electronics

Directed Electronics Hornet 563T Manuel utilisateur

Directed Electronics

Directed Electronics Intelliguard 850 Manuel utilisateur

Directed Electronics

Directed Electronics VIPER 1000 Manuel utilisateur

Directed Electronics

Directed Electronics PYTHON N426P Manuel utilisateur

Directed Electronics

Directed Electronics 551R Series Manuel utilisateur

Directed Electronics

Directed Electronics VIPER 3203 Manuel utilisateur

Directed Electronics

Directed Electronics 446 Series Manuel utilisateur

Directed Electronics

Directed Electronics Python 500 Manuel utilisateur

Directed Electronics

Directed Electronics Rattler 250 Manuel utilisateur

Directed Electronics

Directed Electronics Viper 571XV Manuel utilisateur

Directed Electronics

Directed Electronics Viper 211HV Manuel utilisateur

Manuels Alarme de voiture populaires d'autres marques

Clifford

Clifford 3606X Manuel utilisateur

Ultra Start

Ultra Start 2500M SERIES Manuel utilisateur

Ultra Start

Ultra Start 650 Series Manuel utilisateur

Audiovox

Audiovox Prestige Platinum+ APS-511C Manuel utilisateur

Sparkrite

Sparkrite SRA8 Manuel utilisateur

Viper

Viper 4708V Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manuel

Falcon

Falcon Predator XL3 Guide de l'utilisateur

Audiovox

Audiovox Auto Security XR91 Mode d'emploi

Clifford

Clifford Sabre II Manuel utilisateur

CrimeStopper

CrimeStopper CS-8717 Guide de démarrage rapide

Ultra Start

Ultra Start 450 SERIES Manuel utilisateur

Scytek electronic

Scytek electronic Vectra X3 Manuel utilisateur

Excalibur

Excalibur AL-1860-EDPB Manuel utilisateur

Clifford

Clifford CYBER 2 Manuel utilisateur

Gemini

Gemini 7057 Manuel utilisateur

FlashLogic

FlashLogic FLRSBA PRESTIGE Manuel utilisateur

Magicar

Magicar FAI-440 Manuel utilisateur