Dimplex CDS8515 Manuel utilisateur

7207100100rev06

Owner’s Manual

Model Numbers:

TDS8515

CDS8515

Valued Customer,

Thank you and congratulations for purchasing a Dimplex

electric stove. Over the years, valuable memories

will occur around the warmth and comfort of your stove.

Thank you for allowing our product to be the backdrop

for those special moments.

Serial Number

Model Number

Part Number

Quality checked by:

QUICK REFERENCE GUIDE

1. Before using the stove verify:

• Are the circuit breakers for the unit on?

• Are the light bulbs loose? (To check, follow

the instructions for replacing the light bulbs

under the maintenance section of this

manual)

2. The heater may emit a slight, harmless odor

when rst used. This odor is a normal condition

caused by the initial heating of internal heater

parts.

3. The information regarding the model of your

unit can be found on the rating plate. See Page

6 for an illustration on how to locate the rating

plate.

4. If you have any questions or concerns

regarding the operation of your stove, contact

Dimplex customer service at 1-888-DIMPLEX

(1-888-346-7539)

CONTENTS

Important Instructions . . . . . . . . . . . . . . . . Page 4

Model and Serial Number Information. . . . Page 6

Stove Installation . . . . . . . . . . . . . . . . . . . . Page 7

Operation.......................... Page 7

Maintenance.......................Page 11

Warranty ......................... Page 14

!NOTE: This equipment has been tested and found to comply with the limits for Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

· Reorient or relocate the receiving antenna.

· Increase the separation between the equipment and the receiver.

· Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

· Consult the dealer or an experienced radio/TV technician for help.

Operation is subject to the following two conditions: (1) this device may not cause

interference and (2) this device must accept any interference, including interference that

may cause undesired operation of the device.

IMPORTANT INSTRUCTIONS

Retain this User’s Guide for Future Reference

When using electrical appliances, basic precautions should always be followed

to reduce the risk of re, electric shock, and injury to persons, including the

following:

1. Read all instructions before using the stove.

2. The heater is hot when in use. To avoid burns, do not let bare skin touch

hot surfaces. The trim around the heater outlet becomes hot during heater

operation. Keep combustible materials, such as furniture, pillows, bedding,

papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the

unit.

CAUTION: High Temperature, keep electrical cords, drapery, and

other furnishings at least 3 feet (0.9 m) from the front of the heater

and away from the side and rear.

3. Extreme caution is necessary when any heater is used by or near children

or invalids and whenever the unit is left operating and unattended.

4. Always unplug the stove when not in use.

5. Do not operate any unit with a damaged cord or plug, or if the heater

has malfunctioned, or if the stove has been dropped or damaged in any

manner. Return heater to authorized service facility for examination,

electrical or mechanical adjustment, or repair.

6. Do not use outdoors.

7. The stove is not intended for use in bathrooms, laundry areas and similar

indoor locations. Never locate heater where it may fall into a bathtub or

other water container.

8. Do not run the cord under carpeting. Do not cover cord with throw rugs,

runners, or the like. Arrange cord away from trafc area and where it will

not be tripped over.

9. To disconnect the unit, turn the controls off, then remove the plug from the

outlet.

10. Do not insert or allow foreign objects to enter any ventilation or exhaust

opening as this may cause an electric shock or re, or damage to the

heater.

11. To prevent a possible re, do not block air intake or exhaust in any manner.

Do not use on soft surfaces, like a bed, where openings may become

blocked.

12. All electrical heaters have hot and arcing or sparking parts inside. Do not

use in areas where gasoline, paint, or ammable liquids are used or stored

or where the unit will be exposed to ammable vapors.

13. Do not modify the stove. Use it only as described in this manual. Any other

use not recommended by the manufacturer may cause re, electric shock

or injury to persons.

14. To reduce the risk of electric shock, this appliance has a polarized plug

(one blade is wider than the other). This plug will t in a polarized outlet

only one way. If the plug does not t fully in the outlet, reverse the plug. If

it still does not t, contact a qualied electrician to install the proper outlet.

Do not change the plug in any way. Avoid the use of an extension cord.

Extension cords may overheat and cause a risk of re. If you must use an

extension cord, the cord must be No. 14 AWG minimum size and rated no

less than 1875 Watts.

15. Do not burn wood or other materials in the stove.

16. Do not strike the clear door panel.

17. Always use a certied electrician should new circuits or outlets be required.

18. Always use properly grounded, fused and polarized outlets.

19. Disconnect all power supply before performing any cleaning, maintenance

or relocation of the unit.

20. When transporting or storing the unit and cord, keep in a dry place, free

from excessive vibration and store so as to avoid damage.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

SAVE THESE INSTRUCTIONS

!NOTE: Procedures and techniques that are considered important

enough to emphasize.

CAUTION: Procedures and techniques which, if not carefully

followed, will result in damage to the equipment.

WARNING: Procedures and techniques which, if not carefully

followed, will expose the user to the risk of re, serious injury,

illness or death.

Figure 1

Serial Number

Model Number Part Number

Model and Serial Number Information

If you have any questions about our products please have the product

model and serial numbers available upon calling Dimplex customer

service. To locate the model and serial number see below (Figure 1).

Stove Installation

!NOTE: A 15 Amp, 120 Volt circuit is required. A dedicated circuit

is preferred but not essential in all cases. A dedicated circuit will

be required if, after installation, the circuit breaker trips or fuse

blows on a regular basis when the heater is operating. Additional

appliances on the same circuit may exceed the current rating of the

circuit breaker.

WARNING: Ensure the power cord is not installed so that it is

pinched or against a sharp edge and ensure that the power cord is

stored or secured to avoid tripping or snagging to reduce the risk of

re, electric shock or injury to persons.

Construction and electrical outlet wiring must comply with local

building codes and other applicable regulations to reduce the risk of

re, electric shock and injury to persons.

Do not attempt to wire your own new outlets or circuits. To reduce

the risk of re, electric shock or injury to persons, always use a

licensed electrician.

1. Make sure the unit’s Main ON/OFF switch is switched OFF (refer

to operating instruction section).

2. Plug the unit into a 15 Amp/120 Volt outlet. If the cord does not

reach, you may use an extension cord rated for a minimum of 1875

Watts.

Operation

To access the controls, go to the back of the stove (Figure 2).

Figure 2

Back View Front View

A. Main Power ON/OFF Switch

The Main Power ON/OFF Switch supplies power to all unit functions

(ame, Purire™, and heater).

B. Manual Selection Switch

To choose between ame effect setting, ame effect with Purire™

setting, and ame effect with Purire™ and heat setting.

Pressing the switch up (“ I” position) has the same effect as the ON

button on the remote control and pressing the switch down (“ II ”

position) has the same effect as the OFF button of the remote control.

Pressing the switch up once activates Level 1, twice activates Level

2, three times activates Level 3. Pressing the switch down turns the

electric stove OFF.

Level 1: The ame effect is turned on and the rst red indicator is

activated.

Level 2: The ame effect remains on, the Purire™ is activated, and

the rst and second red indicator lights are activated.

Level 3: The ame effect and Purire™ remain on, the heater is

activated, and all three red indicator lights are activated.

C. Interior Light ON/OFF Switch

The Interior Light On/Off Switch supplies power to the interior light.

D. Heater Thermostat Control

To adjust the temperature to your individual requirements, turn the

thermostat control clockwise all the way to turn on the heater. When

the room reached the desired temperature, turn the thermostat knob

counter clockwise until you hear a click. Leave in this position to

maintain the room temperature at this setting. For additional heat, turn

clockwise until you hear the click again and the heater will turn on.

E. LED Indicators

Indicates the current

function of the stove

(Figure 3).

!NOTE: The heater

may emit a slight,

harmless odor when

rst used. This odor is a normal condition caused by initial heating

Figure 3

Level 1 Indicator

Level 2 Indicator

Level 3 Indicator

of internal heater parts and will not occur again.

Resetting the Temperature Cutoff Switch

This unit is equipped with a thermostat which controls the temperature

of the room. It does this by turning the heater on and off. The heater

is protected with a safety device to prevent overheating. Should the

heater overheat, an automatic cut out will turn the heater off and it will

not come back on without being reset. It can be reset by switching

the Main ON/OFF Switch to OFF and waiting ve (5) minutes before

switching the unit back on.

CAUTION: If you need to continuously reset the heater, unplug the

unit and call your local dealer.

Remote Control Usage

The stove is supplied with a radio frequency remote control. This

remote control has a range of approximately 50 feet (15.25 m). It

does not have to be pointed at the stove and can pass through most

obstacles (including walls). It is supplied with one of 243 independent

frequencies to prevent interference with other units. The frequency

designation is indicated on the back of the transmitter (Figure 4).

The remote control operates the stove levels sequentially. The level is

increased every time the ON button on the transmitter is pressed. The

stove can be turned off at any point by pressing the OFF button on the

remote control transmitter.

Level 1: The ame effect is turned on and the rst red indicator is

activated.

Level 2: The ame effect remains on, the Purire™ is activated, and

the rst and second red indicator lights are activated.

Level 3: The ame effect and Purire™ remain on, the heater is

activated, and all three red indicator lights are activated.

!NOTE: When the stove is turned on by transmitter the stove will

start with ames only. The level can be increased every time the

ON button on the transmitter is pressed.

Remote Control

Initialization

Follow these steps for remote

control initialization and if

required, re-initialization:

1. Ensure that power is

supplied through the main

service panel.

2. Access the manual controls.

3. Locate manual controls.

4. Activate main power switch.

5. Press and hold the side of

the Manual Selection

Switch marked “ I ” for ve

(5) seconds (red indicator light will ash).

6. Press the ON button located on the remote control transmitter.

This will synchronize the remote control transmitter and receiver.

Battery Replacement

To replace the battery:

1. Slide battery cover open on the hand held transmitter (Figure 4).

2. Correctly install one (1) 12 Volt (A23) battery in the battery holder.

3. Close the battery cover.

Maintenance

WARNING: Disconnect power before attempting any maintenance

or cleaning to reduce the risk of re, electric shock or damage to

persons.

Light Bulb Replacement

WARNING: Allow at least ve (5) minutes for light bulbs to cool off

before touching bulbs to avoid accidental burning of skin.

Light bulbs need to be replaced when you notice a dark section of

the ame or when the clarity and detail of the log exterior disappears.

Figure 4

Button

Off

Button

Battery

Cover

Frequency Code

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dimplex Poêle

Dimplex

Dimplex Ritz Manuel utilisateur

Dimplex

Dimplex Opti-V 360 Manuel utilisateur

Dimplex

Dimplex DS5603 Guide de démarrage rapide

Dimplex

Dimplex 143348BK Manuel utilisateur

Dimplex

Dimplex EOSM-2007 Manuel utilisateur

Dimplex

Dimplex EOS-2006 Guide de démarrage rapide

Dimplex

Dimplex Club CLB20 Manuel utilisateur

Dimplex

Dimplex ELECTRIC PATIO STOVE Manuel utilisateur

Dimplex

Dimplex DS2205 Manuel utilisateur

Dimplex

Dimplex Stockbridge SKG20BL Mode d’emploi

Dimplex

Dimplex OAKMEAD OKM20 Manuel utilisateur

Dimplex

Dimplex Opti-myst Evandale Slate EVN20SL Mode d’emploi

Dimplex

Dimplex Corner Standing Stove Manuel utilisateur

Dimplex

Dimplex ELECTRALOG CS2307 Manuel utilisateur

Dimplex

Dimplex Opti-myst Cassington CSN20 Manuel utilisateur

Dimplex

Dimplex OPTIMYST FORTROSE FOR20 Manuel utilisateur

Dimplex

Dimplex Rectory Manuel utilisateur

Dimplex

Dimplex DS5629 Manuel utilisateur

Dimplex

Dimplex Lucia LUC20-EU Manuel utilisateur

Dimplex

Dimplex Burgate Manuel utilisateur

Dimplex

Dimplex Optiflame Electric Fireplace Mode d’emploi

Dimplex

Dimplex OPTIMYST RTOPSTV20 Manuel utilisateur

Dimplex

Dimplex BAR20-AU Manuel utilisateur

Dimplex

Dimplex Westcott Manuel utilisateur

Manuels Poêle populaires d'autres marques

Arada

Arada Cassette Stove Manuel utilisateur

Parmco

Parmco FS 600 Manuel utilisateur

MCZ

MCZ SUITE AIR 10 M2 Manuel utilisateur

HearthStone

HearthStone Stowe DV 8321 Guide de dépannage

Cattara

Cattara FAMILY Manuel utilisateur

Stanley

Stanley Argon F500 OVAL Manuel utilisateur

Avalon

Avalon B-VENT Manuel utilisateur

Nordpeis

Nordpeis Vega Manuel utilisateur

Exquisit

Exquisit EKC601-5 Manuel d'utilisation

Stanley

Stanley Oisin Oil MK II Manuel du propriétaire

Thermocet

Thermocet Brookfield S/CC Manuel utilisateur

HASE

HASE delhi Manuel utilisateur

Vermont Castings

Vermont Castings Intrepid 2 Manuel utilisateur

Italiana Camini

Italiana Camini CLASSICA Guide de démarrage rapide

Avalon

Avalon Vashon Avanti DVS FS Manuel utilisateur

Spartherm

Spartherm ambiente a1 Manuel utilisateur

Warmlite

Warmlite WL46040 Manuel utilisateur

Regency

Regency Ultimate U39E Series Guide de démarrage rapide