Dimplex THWG XLF50 Manuel utilisateur

Owner’s Manual

Model

XLF50

XLF74

XLF100

7214410100R05

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician or

service agency to repair this replace.

!NOTE: Procedures and tech-

niques that are considered important

enough to emphasize.

CAUTION: Procedures and tech-

niques which, if not carefully followed,

will result in damage to the equip-

ment.

WARNING: Procedures and

techniques which, if not carefully

followed, will expose the user to

the risk of re, serious injury, or

death.

Welcome & Congratulations ...................... 3

IMPORTANT INSTRUCTIONS ......................4

Quick Reference Guide .......................... 6

Fireplace Installation ............................ 7

Installation .................................... 7

For Bathroom Use ............................. 12

Final Assembly ............................... 12

Operation .................................... 14

Maintenance ................................. 19

Warranty .................................... 20

Technical Support ............................. 22

Welcome & Congratulations

Thank you and congratulations for purchasing an electric replace from

Dimplex. Please use our convenient online registration page to record

your model and serial numbers for future reference at

www.dimplex.com/register

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

In order to better serve you, please have your model and serial number

ready or register your product online before calling (See above)

Model and Serial

Number Label

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in

a possible electric shock, re hazard and will void the warranty.

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

① Read all instructions before

installing or using this electric

replace.

② This replace is hot when in

use. To avoid burns, do not let

bare skin touch hot surfaces.

The trim around the heater outlet

becomes hot during heater opera-

tion.

DANGER: High temperatures

may be generated under certain

abnormal conditions. Do not par-

tially or fully cover or obstruct the

front of this heater.

③Extreme caution is neces-

sary when any heater is used by

or near children or invalids and

whenever the unit is left operating

and unattended.

④Young children should be

supervised to ensure that they do

not play with the appliance.

⑤ The appliance is not intended

for use by young children or

inrmed persons without supervi-

sion.

IMPORTANT INSTRUCTIONS

⑥Do not operate the unit after

it malfunctions. Disconnect power

at the service panel and contact

Dimplex Technical Service for ser-

vice 1-888-346-7539.

⑦ Do not use outdoors.

⑧Never locate replace where

it may fall into a bathtub or other

water container.

⑨ To disconnect the replace,

turn the controls off, then dis-

connect the circuit at the main

disconnect panel.

⑩ Do not locate the heater im-

mediately below a xed socket-

outlet.

⑪Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑫ To prevent a possible fire, do

not block air intakes or exhaust in

any manner.

⑬ All electrical heaters have

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable

liquids are used or stored.

SAVE THESE INSTRUCTIONS

⑭Use this heater only as

described in this manual. Any

other use not recommended by

the manufacturer may cause re,

electric shock or injury to persons.

⑮Do not burn wood or other

materials in the electric replace.

⑯ Do not strike the replace

glass.

⑰ Always use a certied elec-

trician should new circuits be

required.

⑱ Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

⑲When transporting or stor-

ing the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

WARNING: Remote control

contains small batteries. Keep

away from children. If swallowed,

seek medical attention immedi-

ately.

WARNING: Do not install bat-

tery backwards, charge, put in re

or mix with used or other battery

types - may explode or leak caus-

ing injury.

!NOTE: Changes or modica-

tions not expressly approved by

the party responsible for compli-

ance could void user's authority to

operate the equipment.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICABLE PARTS INSIDE

IMPORTANT INSTRUCTIONS

6 www.dimplex.com

Quick Reference Guide

Figure 1

1. The electrical information re-

garding your electric replace

can be found on the rating

label located on the top of the

unit.

Please use our convenient online

registration page to record your

model and serial numbers for

future reference at

www.dimplex.com/register

2. If you have any technical

questions or concerns re-

garding the operation of your

electric replace, or require

service contact customer ser-

vice at 1-888-346-7539.

3. For dimensions of your re-

place, refer to Figure 1.

16.49 in

419 mm

15.82 in.

402 mm

15.00 in.

381 mm

5.79 in.

147 mm

4.34 in.

110 mm

XLF50 50.31 in [1278 mm]

XLF74 74.31 in [1887 mm]

XLF100 100.31 in [2548 mm]

XLF50 51.41 in [1306 mm]

XLF74 75.41 in [1941 mm]

XLF100 101.41 in [2576 mm]

CAUTION: Ensure installation

does not allow replace to be in

direct contact with building vapor

barrier or insulation and meets all

local building code.

!NOTE: A dedicated, properly

fused 15 Amp circuit is re-

quired, rated for the appropri-

ate voltage (120V, 240V).

WARNING: Construction and

wiring must comply with local

building codes and other ap-

plicable regulations to reduce

the risk of re, electric shock

and injury to persons.

WARNING: To reduce the risk

of re, electric shock or injury to

persons, always use a licensed

electrician.

WARNING: To reduce the

risk of re, do not store or

use gasoline or other am-

mable vapors or liquids in the

vicinity of the heater.

1. Select a location that is

not susceptible to mois-

ture and is away from

drapes, furniture and high

trafc.

2. Unpack the replace and

hardware from the box.

!NOTE: Leave the front

Fireplace Installation

glass and partially reective

glass, safely, in the box until

the time you are ready to

install it.

3. Store the replace in a safe,

dry and dust free location until

you are ready to install the

replace.

Installation

CAUTION: Two people will be

required for various steps of

this procedure.

This design of this unit allows

three options for installation:

partial recess, ush mounted or

sub-surface mounted.

CAUTION: Sub-surface

mounting should be limited

XLF50: 50 5/8" (128.6 cm)

2” x 6”

5 1/2" (14.0 cm)

16"

(40.6 cm)

XLF74: 74 5/8" (189.7 cm)

XLF100: 100 5/8" (255.7 cm)

2” x 4”

3 1/2" (9.0 cm)

Figure 2

8 www.dimplex.com

Fireplace Installation

to ½ in. (10 mm) to ensure

adequate air ow of heated air

out of the rebox area.

1. Prepare a wall with a framed

opening of 16 in. (40.6 cm)

high,

• XLF50 - 50 ⅝ in. (128.7 cm)

• XLF74 - 74 ⅝ in. (189.7 cm)

• XLF100 - 100 ⅝ in. (255.7 cm)

wide, with a bottom sill that is

a minimum of 3.5 in. (9.0 cm)

deep (gure 2). The sill can

be constructed to support the

front of the unit to allow the

power supply wires to easily

be run behind or ush with the

back of the unit and a pass

thru hole drilled for electrical

wire routing.

!NOTE: It is recommended that

the bottom of the unit be mounted

between 30 in. (76.2 cm) and 40

in. (102 cm) from the ground to

maintain an optimized viewing

angle of the ame.

WARNING: Do not attempt

to wire your own new circuits. To

reduce the risk of re, electric shock

or injury to persons, always use a

licensed electrician.

WARNING: Ensure that the

circuit on which the replace is to

be installed has the power cut off

at the service panel until installa-

tion is complete.

2. The unit is provided with an

installed ¾ in. (2.0 cm) trim.

Depending on the installation,

this trim can be removed by

removing the securing screws

and the 4 trim pieces.

3. Ensuring a minimum of 18 in.

(46.7 cm) of slack, route the

supply power wire through a

cable clamp (not included) and

in the opening in the back of

the unit. (Figure 3)

4. Lift replace, from the bottom

and the handles located on the

back, and insert into opening

to the desired depth.

5. Using a bubble level (supplied)

ensure that the replace is level

within the framing. Adjust as

Figure 3

Grounding

Screw

Cable Clamp

Fireplace Installation

required.

6. Drive four supplied mounting

screws through the four mount-

ing holes located on the inside

surface of the replace chassis,

into wall studs (Figure 4).

120V Installation - Direct Wire

!NOTE: The unit is designed

to be hardwired to a power

source and should not have

a cord installed to allow the

unit to be plugged into a wall

receptacle.

Use two conductor, non-metallic

sheath cable with ground wire

(3 wires total) for the incoming

power supply.

CAUTION: Use the appropri-

ate wire to meet local and

national electrical codes for

rated power consumption.

Figure 4

Mounting Holes

• Cut the wire to an appropriate

length.

• Connect the L wire from the

unit to the live wire from the

power supply with a wire nut.

• Connect the N wire from the

unit to the neutral wire from

the power supply with a wire

nut.

• Connect the G wire from the

unit to the ground wire from

the power supply with a wire

nut or attach the ground-

ing wire to the cover with the

provided grounding screw, by

placing the wire in-between

screw and lock washer and

tighten (Figure 3).

• Ensure that all wires are se-

cure and do not protrude past

the ame panel, so as not to

be visible after nal assembly.

Flame

Panel

10 www.dimplex.com

Fireplace Installation

• Continue to the nal assembly

instructions.

120V Installation - Wall Switch

!NOTE: Use a single pole,

single throw (On/Off) wall switch

that is rated for a minimum of 15

amps.

!NOTE: The unit is designed

to be hardwired to a power

source and should not have

a cord installed to allow the

unit to be plugged into a wall

receptacle.

Use two conductor, non-metallic

sheath cable with ground wire

(3 wires total) for the incoming

power supply.

CAUTION: Use the appropri-

ate wire to meet local and

national electrical codes for

rated power consumption.

• Cut the wire to an appropriate

length.

• Connect the L wire from the

unit to the live wire from the

main power through the wall

switch, ensuring all live con-

nections are connected with a

wire nut.

• Connect the N wire from the

unit to the neutral wire from

the power supply with a wire

nut.

• Connect the G wire from the

unit to the ground wire from

the power supply with a wire

nut or attach the ground-

ing wire to the cover with the

provided grounding screw, by

placing the wire in-between

screw and lock washer and

tighten (Figure 3).

• Ensure that all wires are se-

FIREPLACE JUNCTION BOX

120 V

POWER

SUPPLY

(BREAKER

PANEL)

WHITE - N

BLACK – L1

WHITE – N

BLACK – L1

GROUND - G

WALL

SWITCH

GROUND - G

Autres manuels pour THWG XLF50

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Dimplex Cheminée intérieure

Dimplex

Dimplex BEETHOVEN Manuel utilisateur

Dimplex

Dimplex SP16 Manuel utilisateur

Dimplex

Dimplex BF5000NT Guide de démarrage rapide

Dimplex

Dimplex BURLINGTON BLN12 Manuel utilisateur

Dimplex

Dimplex Auvergne Log 2920 Manuel utilisateur

Dimplex

Dimplex Vivente Plus V V T75 Manuel

Dimplex

Dimplex Atherton ATH20 Mode d’emploi

Dimplex

Dimplex PRISM 34 Manuel utilisateur

Dimplex

Dimplex XHD28L Manuel utilisateur

Dimplex

Dimplex DF2608 Manuel utilisateur

Dimplex

Dimplex Toluca Deluxe Manuel utilisateur

Dimplex

Dimplex Shaftsbury SHA20 Manuel utilisateur

Dimplex

Dimplex DFB8842 Manuel utilisateur

Dimplex

Dimplex DF2608-INT Manuel utilisateur

Dimplex

Dimplex Optisuite2Go Manuel utilisateur

Dimplex

Dimplex DF2608 Manuel utilisateur

Dimplex

Dimplex DF2690 Manuel utilisateur

Dimplex

Dimplex NAVARRA NAV15P PEBBLE Manuel du propriétaire

Dimplex

Dimplex DF2608 Manuel utilisateur

Dimplex

Dimplex MIDI FIRE MIDI32B Manuel utilisateur

Dimplex

Dimplex JAZ20N Manuel utilisateur

Dimplex

Dimplex EF2870 Manuel utilisateur

Dimplex

Dimplex DF2608-EU Manuel utilisateur

Dimplex

Dimplex BLF50 Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation