Dimplex IN-STUD V1525BT Manuel utilisateur

Owner’s Manual

Model

V1525BT

V1525RT

7208630100R03

IMPORTANT SAFETY INFORMATION: Always read this manual rst before

attempting to install or use this replace. For your safety, always comply with all

warnings and safety instructions contained in this manual to prevent personal

injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician or

service agency to repair this replace.

!NOTE: Procedures and

techniques that are considered

important enough to emphasize.

CAUTION: Procedures and

techniques which, if not carefully

followed, will result in damage to the

equipment.

WARNING: Procedures and

techniques which, if not carefully

followed, will expose the user to

the risk of re, serious injury, or

death.

Welcome & Congratulations ..................3

IMPORTANT INSTRUCTIONS ................4

Fireplace Installation ........................7

Wall Mounting Instructions ....................8

Built-In Instructions .........................11

Bathroom Installation .......................13

Operation ................................14

Maintenance .............................16

Warranty ................................18

Replacement Parts .........................20

Welcome & Congratulations

Thank you and congratulations for

choosing to purchase an electric

replace from Dimplex, the world

leader in electric replaces.

Please carefully read and save

these instructions.

CAUTION: Read all instructions

and warnings carefully before starting

installation. Failure to follow these

instructions may result in a possible

electric shock, re hazard and will

void the warranty.

Please record your model and serial

numbers below for future reference:

model and serial numbers can

be found on the Model and Serial

Number Label of your replace.

Model Number

Label

Serial Number

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

① Read all instructions before

using this appliance.

② The heater is hot when in use.

To avoid burns, do not let bare

skin touch hot surfaces. The trim

around the heater outlet becomes

hot during heater operation.

Keep combustible materials, such

as furniture, pillows, bedding,

papers, clothes, and curtains at

least 3 feet (0.9m) from the front

of the unit and keep them away

from the sides and rear..

③ Extreme caution is neces-

sary when any heater is used by

or near children or invalids and

whenever the unit is left operating

and unattended.

④ Always unplug the fireplace

when not in use.

⑤ Do not operate any heater

after it malfunctions. Disconnect

power at the service panel and

have the heater inspected by a

reputable electrician before reus-

ing.

⑥ Do not operate any unit with

a damaged cord or plug, or if the

IMPORTANT INSTRUCTIONS

heater has malfunctioned, or if

the electric replace has been

dropped or damaged in any man-

ner, contact Dimplex Technical

Service at 1-888-346-7539.

⑦ Do not use outdoors.

⑧ Never locate heater where it

may fall into a bathtub or other

water container.

⑨ Do not run the cord under

carpeting (for units supplied with

a cord). Do not cover cord with

throw rugs, runners or the like.

Arrange cord away from traf-

c area and where it will not be

tripped over.

⑩ To disconnect the unit, turn

the controls off, then remove the

plug from the outlet or switch off

at main power supply panel if the

unit is hardwired.

⑪ Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑫ To prevent a possible re, do

not block air intake or exhaust in

any manner.

⑬ All electrical heaters have

hot and arcing or sparking parts

inside. Do not use in areas where

SAVE THESE INSTRUCTIONS

gasoline, paint, or ammable

liquids are used or stored.

⑭ Do not modify the replace.

Use it only as described in this

manual. Any other use not rec-

ommended by the manufacturer

may cause re, electric shock or

injury to persons.

⑮ To reduce the risk of electric

shock, this appliance has a polar-

ized plug (one blade is wider than

the other). This plug will t in a

polarized outlet only one way. If

the plug does not t fully in the

outlet, reverse the plug. If it still

does not t, contact a qualied

electrician to install the proper

outlet. Do not change the plug in

any way.

⑯ Always plug heaters directly

into a wall outlet/receptacle.

Never use with an extension cord

or relocatable power tap (outlet/

power strip).

⑰ Do not burn wood or other

materials in the replace.

⑱ Do not strike the glass front.

⑲ Always use a certied electri-

cian for build-in hard-wired instal-

lation.

⑳ Always use properly grounded,

fused and polarized outlets.

㉑ Disconnect all main power

supply (unplug the unit or switch

off at main service panel) before

performing any cleaning, mainte-

nance or relocation of the unit.

㉒ Do not operate the replace

without the glass assembly and/

or frame.

㉓When transporting or stor-

ing the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

㉔ Do not put combustible mate-

rial, liquid or small articles such

as sand inside glass assembly.

IMPORTANT INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

6 www.dimplex.com

CAUTION: This equipment has

been tested and found to comply with

the limits for Class B digital device,

pursuant to part 15 of the FCC

Rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation. This equipment

generates, uses and can radiate

radio frequency energy and, if not

installed and used in accordance with

the instructions, may cause harmful

interference to radio or television

reception, which can be determined

by turning the equipment off and

on, the user is encouraged to try to

correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between

the equipment and the receiver.

• Connect the equipment into an

outlet on a circuit different from

that to which the receiver is

connected.

• Consult the dealer or an

experienced radio/TV technician

for help.

Operation is subject to the following

two conditions: (1) this device may

not cause interference and (2) this

device must accept any interference,

including interference that may cause

undesired operation of the device.

IMPORTANT INSTRUCTIONS

WARNING: Remote control

contains small batteries. Keep away

from children. If swallowed, seek

medical attention immediately.

WARNING: Do not install battery

backwards, charge, put in re or mix

with used or other battery types - may

explode or leak causing injury.

!NOTE: Changes or modications

not expressly approved by the party

responsible for compliance could

void user's authority to operate the

equipment.

Fireplace Installation

Figure 1

WARNING: Ensure the power

cord is not installed so that it is

pinched or against a sharp edge

and ensure that the power cord is

stored or secured to avoid tripping

or snagging to reduce the risk

of re, electric shock or injury to

persons.

WARNING: Construction

and electrical outlet wiring must

comply with local building codes

and other applicable regulations

to reduce the risk of re, electric

shock and injury to persons.

WARNING: Do not attempt

to wire your own new outlets or

circuits. To reduce the risk of re,

electric shock or injury to persons,

always use a licensed electrician.

WARNING: To reduce the risk

of re, do not store or use gaso-

line or other ammable vapors or

liquids in the vicinity of the heater.

!NOTE: A 15amp, 120-volt cir-

cuit is required. A dedicated cir-

cuit is preferred but not essential

in all cases. A dedicated circuit

will be required if, after installa-

tion, the circuit breaker trips or

the fuse blows on a regular basis

when the heater is operating. Ad-

ditional appliances on the same

circuit may exceed the current

rating of the circuit breaker.

WARNING: The In-Stud

replace is wall mountable and

can be build-in the wall space 16”

(406 mm) over-center between

2” (51 mm) x 4” (102 mm) wall

studs. Follow the installation in-

structions for either wall mount or

built-in mounting; failure to do so

may cause damage or injury.

!NOTE: Remove glass as-

sembly before installing re-

place on or into a wall.

CAUTION: High temperature,

risk of re, keep electrical

8 www.dimplex.com

Fireplace Installation

Figure 2

cords, drapery, furnishings,

and other combustibles at

least 3 feet (0.9 m) from the

front of the heater.

1. Remove screws securing

glass assembly on the mount-

ing tabs. (Figure 1)

2. Use both handles on the

sides of the glass assembly,

lift and remove the assembly

from the replace.

3. Please glass assembly with

it’s back facing down on a at

surface.

Wall Mounting Instructions

1. Leave the trim uninstalled

until step 9.

2. Select a location for the

replace, preferably above

an electrical outlet and there

must be at least one wall stud

behind for the replace to

mount onto. The bottom of

the unit must be a minimum

of 4” (102 mm) space above

the oor (mounting holes

29.5” (750 mm) minimum

above the oor). Access

to the electrical outlet must

be maintained. Ensure the

installation meets the national

and state/provincial electrical

codes.

!NOTE: It is recommended

that the bottom of the unit not be

mounted higher than 48” (122 cm)

from the ground to maintain an

optimized viewing angle of the

ame.

CAUTION: The replace must

be mounted at two points, one of

which must be on a wall stud.

WARNING: High temperatures

may be generated under certain

abnormal conditions. Do not

partially or fully cover or obstruct

the front of this heater. Bottom

of unit must be a minimum of 4”

(102 mm) above oor or any sur-

face such as a tabletop to ensure

Air

Circulation

Figure 3

Fireplace Installation

adequate ventilation through air

intake located at the bottom of the

replace. (Figure 3)

3. With a wall stud nder, locate

the center of the wall stud,

drive a wood screw into stud

and leave approximately 1/8”

(3 mm) exposed threads for

the replace to hang on.

4. The second mounting point

should be picked such that it

is farthest (to the left or right)

relative to the rst one among

the seven keyholes (A to G

shown in gure 2) on the re-

place for wall mounting, these

keyholes are 2” (51 mm)

apart. For example, if you

plan to use hole B as the rst

mounting hole, the second

mounting hole must be G.

Other available combinations

are A-G, C-G, A-F, A-E, A-D

and D-G.

5. Mark the second mounting

screw location; ensure that

is level with the rst with the

help of the provided bubble

level and the replace itself.

Screw the threaded drywall

anchor in the drywall with a

Philip’s head screwdriver until

the head is at against the

wall surface. Caution should

be taken when using a power

tool to install a threaded

drywall anchor as the drywall

may distort, tear or slightly

buckle as a result of over-

torque.

6. With a Philip’s head screw

driver, screw that drywall

anchor screw into the dry-

wall anchor already in the

wall, leave about 1/8” (3 mm)

exposed threads for mounting

the replace.

7. With the glass assembly tak-

en off, mount the rebox onto

the two mounting screws.

8. Tighten both mounting screws

with a screwdriver. Be cau-

tion not to over tighten the

one mated with the drywall

10 www.dimplex.com

Fireplace Installation

1. Install supplied

brackets as shown on

both sides of frame

3. Secure frame on

replace with supplied

self-tapping screws

2. Install frame on to

replace

Figure 4

Figure 5 Figure 6

Autres manuels pour IN-STUD V1525BT

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dimplex Cheminée intérieure

Dimplex

Dimplex CAS500 Manuel utilisateur

Dimplex

Dimplex CAS1000M Manuel utilisateur

Dimplex

Dimplex Ignite 60 Manuel utilisateur

Dimplex

Dimplex Nardini NDN20 Manuel utilisateur

Dimplex

Dimplex BLF74 Manuel utilisateur

Dimplex

Dimplex TOLUCA DELUXE-EU Manuel utilisateur

Dimplex

Dimplex Ignite XLF50 Manuel utilisateur

Dimplex

Dimplex Cadogan CGN20 Manuel utilisateur

Dimplex

Dimplex milano-ef Manuel utilisateur

Dimplex

Dimplex MULTIFIRE DF3015 Manuel utilisateur

Dimplex

Dimplex BLF74 Instructions de construction

Dimplex

Dimplex DFP6975O Manuel utilisateur

Dimplex

Dimplex BFSL33 Manuel utilisateur

Dimplex

Dimplex BINGHAM BHM 10 Manuel utilisateur

Dimplex

Dimplex DFI2309 Manuel utilisateur

Dimplex

Dimplex DFG3033 Manuel utilisateur

Dimplex

Dimplex 6911540100 Manuel utilisateur

Dimplex

Dimplex VFA2927 Manuel utilisateur

Dimplex

Dimplex DCF44GS Manuel utilisateur

Dimplex

Dimplex EWF-SS Manuel utilisateur

Dimplex

Dimplex Ropley RPL20 Mode d’emploi

Dimplex

Dimplex DF2690 Manuel utilisateur

Dimplex

Dimplex BLF74-EU Manuel utilisateur

Dimplex

Dimplex DF2608 Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation