Dimplex ELECTRALOG DF203A Manuel utilisateur
7209520200R01
Owner’s Manual
Model
DF203A
IMPORTANT SAFETY INFORMATION: Always read this manual rst
before attempting to install or use this replace. For your safety, always
comply with all warnings and safety instructions contained in this manual
to prevent personal injury or property damage.
To view the full line of Dimplex products, please visit
www.dimplex.com
2 www.dimplex.com
Table of Contents
Always use a qualied techni-
cian or service agency to repair
this stove.
!NOTE: Procedures and
techniques that are considered
important enough to emphasize.
CAUTION: Procedures and
techniques which, if not carefully
followed, will result in damage to
the equipment.
WARNING: Procedures and
techniques which, if not care-
fully followed, will expose the
user to the risk of re, serious
injury, or death.
Welcome & Congratulations ..........................3
IMPORTANT INSTRUCTIONS ........................4
Fireplace Installation ...............................7
Operation ........................................11
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Warranty ........................................15
Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
3
Welcome & Congratulations
Thank you and congratulations for choosing to purchase an electric
replace from Dimplex, the world leader in electric replaces.
Please carefully read and save these instructions.
CAUTION: Read all instructions and warnings carefully before
starting installation. Failure to follow these instructions may result in a
possible electric shock, re hazard and will void the warranty.
Please record your model and serial numbers below for future
reference: model and serial numbers can be found on the Model and
Serial Number Label.
NO NEED TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information?
Product Under Manufacturer’s Warranty?
Contact us at: www.dimplex.com/customer_support
For Troubleshooting and Technical Support
OR Toll-Free 1-888-346-7539
Monday to Friday 8:00 a.m. to 4:30 p.m. EST
Please have your model number and product serial
number ready. (See above)
S E R IAL No.
MODE L
MOD.
4 www.dimplex.com
When using electrical appliances,
basic precautions should always
be followed to reduce the risk of
fire, electric shock, and injury to
persons, including the following:
① Read all instructions before
using this heater.
② This heater is hot when in use.
To avoid burns, do not let bare
skin touch hot surfaces. The trim
around the heater outlet becomes
hot during heater operation.
Keep combustible materials, such
as furniture, pillows, bedding,
papers, clothes, and curtains at
least 3 feet (0.9 m) from the front
of the heater and keep them away
from the sides and rear.
③ Extreme caution is neces-
sary when any heater is used by
or near children or invalids and
whenever the unit is left operating
and unattended.
④ Always unplug the heater when
not in use.
⑤Do not operate any heater
after it malfunctions. Disconnect
power at the service panel and
have the heater inspected by a
reputable electrician before reus-
ing.
⑥ Do not operate any unit with
IMPORTANT INSTRUCTIONS
a damaged cord or plug, or if the
heater has malfunctioned, or if
the electric replace has been
dropped or damaged in any man-
ner, contact Dimplex Technical
Service at 1-888-346-7539.
⑦ Do not use outdoors.
⑧ This heater is not intended for
use in bathrooms, laundry ar-
eas and similar indoor locations.
Never locate this heater where
it may fall into a bathtub or other
water container.
⑨ Do not run cord under carpet-
ing. Do not cover cord with throw
rugs, runners, or the like. Arrange
cord away from trafc area and
where it will not be tripped over.
⑩ To disconnect heater, turn
controls to off, then remove plug
from outlet.
⑪ Do not insert or allow foreign
objects to enter any ventilation
or exhaust opening as this may
cause an electric shock or re, or
damage the heater.
⑫ To prevent a possible re, do
not block air intakes or exhaust in
any manner.
⑬ All electrical heaters have
hot and arcing or sparking parts
5
SAVE THESE INSTRUCTIONS
inside. Do not use in areas where
gasoline, paint, or ammable
liquids are used or stored.
⑭ Do not modify the heater. Use
it only as described in this man-
ual. Any other use not recom-
mended by the manufacturer may
cause re, electric shock, or injury
to persons.
⑮This unit may have a polarized
plug (one blade is wider than the
other). The plug will t in a polar-
ized outlet only one way. If the
plug does not t fully in the outlet,
reverse the plug. If it still does not
t, contact a qualied electrician
to install the proper outlet.
⑯ Always plug heaters directly
into a wall outlet/receptacle.
Never use with an extension cord
or relocatable power tap (outlet/
power strip).
⑰ Do not burn wood or other ma-
terials in the Compact Fireplace.
⑱ Do not strike the front glass.
⑲ Always use a certied electri-
cian should new circuits or outlets
be required.
⑳ Always use properly grounded,
fused and polarized outlets.
㉑ Disconnect all power supply
before performing any cleaning,
maintenance or relocation of the
heater.
㉒When transporting or storing
the heater and cord, keep in a
dry place, free from excessive
vibration and store so as to avoid
damage.
WARNING: To avoid over-
heating, do not cover heater.
IMPORTANT INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
6 www.dimplex.com
IMPORTANT INSTRUCTIONS
WARNING: Remote control
contains small batteries. Keep away
from children. If swallowed, seek
medical attention immediately.
WARNING: Do not install battery
backwards, charge, put in re or mix
with used or other battery types - may
explode or leak causing injury.
!NOTE: Changes or modications
not expressly approved by the party
responsible for compliance could
void user's authority to operate the
equipment.
!NOTE: This equipment has been
tested and found to comply with
the limits for Class B digital device,
pursuant to part 15 of the FCC
Rules.These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment
generates, uses and can radiate
radio frequency energy and, if not
installed and used in accordance with
the instructions, may cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and
on, the user is encouraged to try to
correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between
the equipment and the receiver.
• Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
• Consult the dealer or an
experienced radio/TV technician
for help.
Operation is subject to the following
two conditions: (1) this device may
not cause interference and; (2) this
device must accept any interference,
including interference that may cause
undesired operation of the device.
7
Fireplace Installation
Unpacking Instructions
The replace insert is packed with
the front glass panel separated
and uninstalled from the replace.
Care must be taken to unpack the
replace so as not to damage the
front glass.
1. Stand the packaged replace
upright as indicated on the
carton (Figure 1).
2. Open the top of the carton
and locate which side the
glass is placed.
3. Remove remote control and
all plastic bags containing
hardware etc.
4. Lay carton at on a level sur-
face so that the glass panel
faces up (Figure 2).
5. Supporting the glass panel,
remove one of the styrofoam
end caps.
6. Remove glass panel from
styrofoam packaging.
7. Remove glass and replace
from all packaging and plastic
wrap.
8. Remove the temporary wood
frame from the rebox by
removing the six screws and
washers as shown in Figure
3.
Figure 2
Glass End Cap
Figure 1
Figure 3
Wood Frame
8 www.dimplex.com
!NOTE: Although the wood
frame can be discarded, the
screws and washers should be
kept to attach the rebox to a
Dimplex mantel or surround (if
applicable).
Fireplace Assembly
The only assembly required is to
place the front glass assembly
onto the replace and install hard-
ware to keep it in place.
1. With the replace laying on
a at and level surface from
Step 3 of the Unpacking
Instructions, turn the glass
retaining brackets into a verti-
cal position.
2. Place the bottom of the glass
panel onto the glass support
track located just in front of
and below the ember bed
(Figure 4A).
3. As shown in Figure 4B, lay
the top of the glass panel
into the corresponding glass
support track at the top of the
viewable replace.
4. Turn the glass retaining
brackets back into the origi-
nal position and secure them
with the supplied screws (1
per side of glass) as shown
in Figure 5. Refer to Figure 6
for an assembled view.
5. Using a at head or Philips
screwdriver, fasten screws
through chassis bracket and
into glass retaining bracket.
6. Repeat for other upper cor-
ner.
Fireplace Installation
WARNING: Ensure the power
cord is not installed so that it is
pinched or against a sharp edge
Figure 4 A
B
Bottom of
Fireplace
Top of
Fireplace
Fireplace Installation
Glass Retaining
Bracket
9
Figure 5
Figure 6
and ensure that the power cord is
stored or secured to avoid tripping
or snagging to reduce the risk
of re, electric shock or injury to
persons.
WARNING: Construction
and electrical outlet wiring must
comply with local building codes
and other applicable regulations
to reduce the risk of re, electric
shock and injury to persons.
WARNING: Do not attempt
to wire your own new outlets or
Fireplace Installation
circuits. To reduce the risk of re,
electric shock or injury to persons,
always use a licensed electrician.
WARNING: To reduce the risk
of re, do not store or use gaso-
line or other ammable vapors or
liquids in the vicinity of the heater.
CAUTION: High temperature,
risk of re, keep electrical
cords, drapery, furnishings,
and other combustibles at
least 3 ft (0.9 m) from the front
of the heater.
!NOTE: A 15amp, 120-volt cir-
cuit is required. A dedicated cir-
cuit is preferred but not essential
in all cases. A dedicated circuit
will be required if, after installa-
tion, the circuit breaker trips or
the fuse blows on a regular basis
Figure 7
x6
10 www.dimplex.com
L1
N
N
SWITCH OUT
CUTOUT THERMOSTAT
M
M
L
HEAT ON/OFF
SWITCH
LIGHT HARNESS
ASSEMBLY
FLICKER
MOTOR
CAPACITOR
BLOWER
MOTOR
ELEMENT
Fireplace Installation
when the heater is operating. Ad-
ditional appliances on the same
circuit may exceed the current
rating of the circuit breaker.
Make sure the units 3-Position
switch is switched OFF (refer to
operating instruction section).
Plug the unit into a 15 Amp/120
VAC outlet.
Mantel Installation
For use with a new or existing
mantel, insert replace as shown
in Figure 7 and anchor in place
with supplied screws.
If not installing the unit into a Dim-
plex mantel the required open-
ing dimensions of the replace
are: 20.4" (517mm) wide x 21.1"
(536mm) high.
(See Figure 8 for all dimensions)
21.9 [555]
20.4 [517]
21.1 [537]
9 [229]
21.1 [536]
22.1 [561]
Figure 8
WIRING
Autres manuels pour ELECTRALOG DF203A
3
Table des matières
Autres manuels Dimplex Cheminée intérieure
Dimplex
Dimplex Clova CLV20B Manuel utilisateur
Dimplex
Dimplex XLF5017-XD Manuel utilisateur
Dimplex
Dimplex Revillusion Osbourne Manuel utilisateur
Dimplex
Dimplex BF36E Manuel utilisateur
Dimplex
Dimplex SACRAMENTO SCR20 Manuel utilisateur
Dimplex
Dimplex ROTHESAY RSY20 Manuel utilisateur
Dimplex
Dimplex BFL50-EU Manuel utilisateur
Dimplex
Dimplex BF9000 Manuel utilisateur
Dimplex
Dimplex BEETHOVEN Manuel utilisateur
Dimplex
Dimplex OPTIMYST CAS400L Manuel utilisateur
Dimplex
Dimplex DF28L-PRO Manuel utilisateur
Dimplex
Dimplex Revillusion RBF30 Manuel utilisateur
Dimplex
Dimplex CLEMENT CMT20BL Manuel utilisateur
Dimplex
Dimplex EWM-COPPER Manuel utilisateur
Dimplex
Dimplex BF33ST Manuel utilisateur
Dimplex
Dimplex CHERITON LED CHT20 Manuel utilisateur
Dimplex
Dimplex Auvergne Log 2920 Manuel utilisateur
Dimplex
Dimplex GDS28L8-904ST Manuel utilisateur
Dimplex
Dimplex Optiflame 3D Braemar BMR20 Mode d’emploi
Dimplex
Dimplex Exbury Manuel utilisateur
