Dimplex DF2608-EU Manuel utilisateur

Owner’s Manual

Model

DF2608-EU

DF2608-AU

6904700000

7209340100R04

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

EN RU UA FR ES IT DE PL

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this replace.

!NOTE: Procedures and

techniques that are

considered important

enough to emphasize.

CAUTION: Procedures and

techniques which, if not

carefully followed, will result

in damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations .............. 3

IMPORTANT SAFETY INSTRUCTIONS ..... 4

Site Selection and Preparation ........... 6

Fireplace Installation ................... 7

Operation ............................. 9

Maintenance ...........................11

Warranty............................. 14

Welcome & Congratulations

Thank you and congratulations for

choosing to purchase an electric

replace from Dimplex, the world

leader in electric replaces.

Please carefully read and save

these instructions.

CAUTION: Read all

instructions and warnings

carefully before starting

installation. Failure to follow

these instructions may result in

a possible electric shock, re

hazard and will void the warranty.

Please record your model and

serial numbers below for future

reference: model and serial

numbers can be found on the

Model and Serial Number Label

of your replace.

Serial Number

Model Number

Figure 1

Questions With the Assembly?

Require Parts Information?

Product Under Manufacturer’s

Warranty?

Call your local dealer

Please have your model number

and product serial number ready.

(See below)

4 www.dimplex.com

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using

this appliance.

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

re, electrical shock and injury to

persons, including the following:

1. If the appliance is damaged,

check with the supplier before

installation and operation.

2. Do not use outdoors.

3. Do not use in the immediate

surroundings of a bath, shower

or swimming pool.

4. Do not locate the appliance

immediately below a xed

socket outlet or connection

box.

5. This appliance can be used

by children aged form 8 years

and above and persons with

reduced physical, sensory or

mental capabilities or lack of

experience and knowledge if

they have been given supervi-

sion or instruction concerning

use of the appliance in a safe

way and understand the haz-

ards involved. Children shall

not play with the appliance.

Cleaning and user mainte-

nance shall not be made by

Children without supervision.

6. Children of less than 3 years

should be kept away unless

continuously supervised.

Children aged from 3 years

and less than 8 years shall

only switch on/off the ap-

pliance provided that it has

been placed or installed in its

intended normal operating

position and they have been

given supervision or instruc-

tion concerning use of the

appliance in a safe way and

understanding the hazards

involved. Children aged from

3 years and less than 8 years

shall not plug in, regulate and

clean the appliance or perform

user maintenance.

7. Do not use this appliance in

series with a thermal control, a

program controller, a timer or

any other device that switches

on the heat automatically,

since a re risk exists when

the appliance is accidentally

covered or displaced.

8. This appliance is not equipped

with a device to control the

room temperature. Do not use

this appliance in small rooms

when they are occupied by

persons not capable of leaving

the room on their own, un-

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

less constant supervision is

provided.

9. Ensure that furniture, curtains

or other combustible material

are positioned no closer than 1

metre from the appliance.

10. In the event of a fault unplug

the appliance.

11. Unplug the appliance when not

required for long periods.

12. Although this appliance com-

plies with safety standards, we

do not recommend its use on

deep pile carpets or on long

hair type of rugs.

13. The appliance must be po-

sitioned so that the plug is

accessible.

14. If the supply cord is damaged

it must be replaced by the

manufacturer or service agent

or a similarly qualied person

in order to avoid a hazard.

15. Keep the supply cord away

from the front of the appliance.

WARNING: In order to avoid

overheating, do not cover the

appliance. Do not place material

or garments on the appliance, or

obstruct the air circulation around

the appliance, for instance by

curtains or furniture, as this could

cause overheating and a re risk.

WARNING: In order to avoid a

hazard due to inadvertent reset-

ting of the thermal cut-out, this

appliance must not be supplied

through an external switching

device, such as a timer, or con-

nected to a circuit that is regularly

switched on and off by the utility.

CAUTION: Some parts of this

product can become very hot and

cause burns. Particular attention

has to be given where children

and vulnerable people are pres-

ent.

The heater carries the Warning Symbol

indicating that it must not be covered

6 www.dimplex.com

Site Selection and Preparation

This section provides instructions

for selecting a location and

preparing the site to install the

replace into your Dimplex mantel

surround.

1. Select a suitable location that

is not susceptible to moisture

and is away from drapes,

furniture and high trafc.

2. For ease of electrical hook

up you may wish to locate

the replace near an existing

outlet (refer to NOTE 1).

3. Store the replace in a safe,

dry and dust free location.

CAUTION: Clearance for air

circulation beneath the replace

is provided by two spacers. DO

NOT INSTALL FIREPLACE

DIRECTLY ON CARPET

OR SIMILAR SURFACES

WHICH MAY RESTRICT AIR

CIRCULATION. If installing the

replace in a carpeted area, place

a one-piece, solid at surface

under the replace. Ensure

that all feet rest securely on this

surface.

!NOTE: The dimensions of the

replace are 667 mm wide X 575

mm high X 222 mm deep. The

replace does not require any

additional venting. With trim, the

dimensions are 695 mm wide X

596 mm high X 222 mm deep.

Figure 2

575

695 mm

596

667 mm

222

WARNING: Ensure the power

cord is not installed so that it

is pinched or against a sharp

edge and ensure that the pow-

er cord is stored or secured to

avoid tripping or snagging to

reduce the risk of re, electric

shock or injury to persons.

Construction and electrical

outlet wiring must comply

with local building codes and

other applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

Do not attempt to wire your

own new outlets or circuits. To

reduce the risk of re, electric

shock or injury to persons,

Fireplace Installation

always use a licensed electri-

cian.

Install the replace assembly into

the mantel (refer to mantel as-

sembly instructions).

!NOTE: A 10 Amp, 240 Volt

circuit is required. A dedicated

circuit is preferred but not es-

sential in all cases. A dedi-

cated circuit will be required

if after installation the circuit

breaker trips or fuse blows

on a regular basis when the

heater is operating. Additional

appliances on the same circuit

may exceed the current rating

of the circuit breaker.

!IMPORTANT: If not using a

Dimplex mantel, the replace

must be installed in an enclo-

sure with the following MINI-

MUM dimensions(Figure 3).

New Wall Construction

1. Select a suitable location that

is not susceptible to moisture

and is away from drapes,

furniture and high trafc.

2. Place the replace in the

desired location to see how it

will look in the room.

3. Mark the desired location on

the oor.

680 mm

585

229

Figure 3

8 www.dimplex.com

Fireplace Installation

4. Use studs to frame an open-

ing of 680 mm wide X 585

mm high X 229 mm deep.

Option #1

The power cord can be run from

behind the trim and along the wall

to an outlet near the replace.

Option #2

A new outlet can be installed

inside the framing construc-

tion. Plug the replace into a 10

Amp/240 Volt outlet. If the cord

does not reach you may use a

3-core type extension cord rated

for a minimum of 10 Amps.

Existing Fireplace:

1. Seal all drafts and vents with

a non-brous insulation mate-

rial to prevent any chimney

debris from falling onto the

replace. Do not install into

an existing replace that is

prone to dampness.

2. Cap the top of the chimney

ue to prevent rain from

entering.

3. Plan your electric power sup-

ply.

4. The power cord can run along

the front of the hearth to an

outlet near the replace.

CAUTION: Clearance for

air circulation beneath the

replace insert is provided by

two spacers. Do not install

the replace insert directly

on carpet or similar sur-

faces which may restrict air

circulation. If installing the

replace in a carpeted area,

place a one-piece, solid, at

surface under the replace

insert. Ensure that all three of

the insert’s feet rest securely

on this surface.

Operation

Manual Control

The manual controls for the

replace are behind the access

panel located at the bottom of the

replace (Figure 4).

A. Flame Action Control

Turn the ame action control knob

to adjust the ame speed to the

desired level.

B. Interior Light Control

Turn the interior light control

knob to increase or decrease the

brightness of the interior light.

C. Level 1 Heat

Provides heat output from one

element.

D. Level 2 Heat

Provides heat output from both

elements.

!NOTE: This switch must be in

the ON (I) position for heater to

operate with or without heat.

E. Heater Thermostat Control

To adjust the temperature to your

individual requirements, turn the

thermostat control clockwise all

the way to turn on the heater.

When the room reaches the

desired temperature, turn the

thermostat knob counter clock-

wise until you hear a click. Leave

in this position to maintain the

room temperature at its setting.

For additional heat, turn clockwise

until you hear the click again and

the heater will turn on. To turn the

heater off, rotate the knob fully

counter clockwise.

F. Main Three Position Switch

The switch has two ON positions

marked with and “I”. The “I“

position is for manual operation.

In this position the built-in remote

control is by-passed.

The position is for operating

the unit with the provided remote

control.

When in position, the unit is

operated with the ON and OFF

buttons of the remote control.

When the switch is in the center

Figure 4 A B C

10 www.dimplex.com

Operation

position the unit is off.

Resetting the Temperature Cut-

off Switch

This unit is equipped with a ther-

mostat which controls the tem-

perature of the room by turning

the heater on and off. The heater

is protected with a safety device

to prevent overheating. Should

the heater overheat, an automatic

cut out will turn the heater off and

it will not come back on without

being reset. It can be reset by

switching the Main Switch to "O"

and waiting 5 minutes before

switching the unit back on.

CAUTION: If you need to con-

tinuously reset the heater, unplug

the unit and call customer service.

Please have your model and se-

rial number ready when calling.

!NOTE: The heater may emit

a slight, harmless odor when rst

used. This odor is a normal con-

dition caused by initial heating of

internal heater parts and will not

occur again.

Remote Control (Figure 5)

The replace is supplied with an

integrated on/off remote control.

Where the maximum rage of use

is ~5m.

WARNING: It takes time for

the receiver to respond to the

transimitter. Do not press the but-

tons more than once within two

seconds for correct operation.

!NOTE: Ensure that the re-

place 3 position switch is set to

the remote control setting (up

position).

To operate, push the ON button

to turn replace on, push the OFF

button to turn the replace off.

Battery Replacement

To replace the battery:

1. Slide battery cover open

on the back of the remote

control.

2. Install AAA batteries into the

remote control.

3. Replace the battery cover.

Discard leaky batteries. Dispose

Figure 5

Autres manuels pour DF2608-EU

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Dimplex Cheminée intérieure

Dimplex

Dimplex LVA191 Manuel utilisateur

Dimplex

Dimplex SAHARA FIREPLACE 6903950000 Manuel utilisateur

Dimplex

Dimplex BLF5051-INT Manuel utilisateur

Dimplex

Dimplex DF2608-EUE Manuel utilisateur

Dimplex

Dimplex Optimyst 3STEP-RGB-EU Mode d’emploi

Dimplex

Dimplex LVA231 Manuel

Dimplex

Dimplex MULTIFIRE DF3015 Manuel utilisateur

Dimplex

Dimplex SP420 Manuel utilisateur

Dimplex

Dimplex SNG20 Manuel utilisateur

Dimplex

Dimplex DCF7850 Manuel utilisateur

Dimplex

Dimplex CAS500R Manuel utilisateur

Dimplex

Dimplex Amesbury AME20 Manuel utilisateur

Dimplex

Dimplex Valencia Manuel utilisateur

Dimplex

Dimplex Chadwick Suite CDW15WW Manuel utilisateur

Dimplex

Dimplex VERDI VER20 Manuel utilisateur

Dimplex

Dimplex BF33STP Manuel utilisateur

Dimplex

Dimplex 25 FIREBOX Manuel utilisateur

Dimplex

Dimplex BF33STP Guide de démarrage rapide

Dimplex

Dimplex MULTIFIRE DF3015 Guide de démarrage rapide

Dimplex

Dimplex Vivente Plus V V T75 Manuel

Dimplex

Dimplex XHD26L Manuel utilisateur

Dimplex

Dimplex DF2624L Manuel utilisateur

Dimplex

Dimplex Nicole Manuel utilisateur

Dimplex

Dimplex DFI2310 Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation