Dimplex Monterey Manuel utilisateur

08/80261/0 ISSUE: 5 Series: A

Dimplex Monterey (MFPE)

Models: MFP050E / MFP075E / MFP100E

MFP150E / MFP200E

These instructions should be read carefully

and retained for future use. Note also the

information presented on the appliance.

INSTRUCTION MANUAL

Installation and Operating

IMPORTANT

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR

FUTURE REFERENCE. Note also the information presented on the appliance

CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/

OR DAMAGE AND MAY INVALIDATE YOUR GUARANTEE

IMPORTANT SAFETY ADVICE

When using electrical heaters, basic precautions should always be followed to reduce

the risk of ﬁ re, electrical shock, and injury to persons, including the following:

IMPORTANT: The wall bracket supplied with the heater must be used.

IMPORTANT: All packaging should be disposed of in an appropriate manner.

OVERHEATING WARNING

WARNING: In order to avoid overheating, do not cover or obstruct the heater. Do not

place material or garments on the heater, or obstruct the air circulation around the heater,

for instance by curtains or furniture, as this could cause overheating and a ﬁ re risk. NEVER

cover or obstruct in any way the heat outlet slots at the top of the heater or the air inlet

slots in the base of the heater.

WARNING:

THE SURFACES ON THIS HEATER CAN BE HOT. The heater carries

a warning ‘DO NOT COVER’ to alert the user to the risk of ﬁ re that exists if the

heater is accidentally covered. DO NOT place combustible items through the

heater grille.

CAUTION: Some parts of this product can become very hot and cause burns. Particular

attention has to be given where children and vulnerable people are present.

For your safety this heater is ﬁ tted with a thermal cut-out. In the event that the

product overheats for some reason, the cut-out prevents excessive temperatures on

the product by cutting the power to the heater. Once the heater has cooled down,

it will reset automatically, it will continue to cycle on and o automatically until the

reason for overheating is removed. The display screen may ﬂ ash red to indicate the

product has overheated. To reset the display, remove the obstruction and hold Enter

for 10 seconds.

SUITABLE APPLICATIONS

WARNING: This heater is suitable for normal domestic household purposes and

should not be used in any other type of environment. This product should only be

used in the country where it was purchased from by a recognised commercial retailer.

Do not use outdoors.

SERVICING AND REPAIRS

WARNING

Servicing and product repairs should only be undertaken by the

manufacturers approved service agent or a similarly trained or qualiﬁ ed person, using

only exact manufacturer approved spare parts.

PLEASE NOTE: Household dust, lit cigarettes, candles and oil burners, combined with

the convection e ect of electric heaters can cause signiﬁ cant soot deposits to build

up on the surface directly above and to the sides of the heater. This is not a fault of the

heater. Extensive burning of candles or smoking in the operating environment of this

product can produce heavy discolouration within a few months of use.

OPERATING WARNINGS

IMPORTANT: Remember to observe all safety warnings and precautions when

operating the heater on the automatic or timer modes, either attended or unattended

since a ﬁ re risk exists when the heater is accidentally covered or displaced.

CAUTION: Do not use if the heater’s mains power lead is damaged. If the supply cord

is damaged it must be replaced by the installer or an approved Dimplex service partner.

ELECTRICAL INSTALLATION

WARNING: The electrical installation of this heater must be carried out by a

suitably qualiﬁ ed or trained electrician, and be in strict accordance with the

current wiring Regulations BS 7671. The supply must be connected via a switched

fused spur with a fuse rated suitably for the appliances ﬂ ex. Failure to follow these

instructions will mean that the manufacturer’s instructions have not been adhered to.

THERE ARE NO EXCEPTIONS.

WARNING: Minimum clearances and IP zone requirements must be adhered to in

accordance with the current wiring regulations.

The wires in this mains lead are coloured in accordance with the following code:

GREEN AND YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

• This heater must be earthed

• Not suitable for connection via a plug top

• Do not locate the heater immediately below a ﬁ xed electrical point i.e. socket outlet.

The heater is ﬁ tted with a length of ﬂ exible cable type H05VV-F size 3 x 1.0mm for 500W

to 2kW models for connection to the ﬁ xed wiring of the premises through a suitable

connection box positioned adjacent to the heater. A means for disconnection must be

incorporated in the ﬁ xed wiring of the premises in accordance with the current wiring

regulations. The supply circuit to the heater must incorporate a double pole isolating

switch having a contact separation of at least 3mm. Products that are supplied without

a plug are for installation into the ﬁ xed wiring of the property, via a suitable double pole

switched fused spur with a fuse rated suitably for the appliances ﬂ ex. Typical fuse ratings

for 230V equipment - Up to 700W = 3A, over 700W = 13A.

In installation the supply cord must be cut to the appropriate length for the electrical

connection point. Excess cable should not be inserted and stored behind the heater.

WARNING: This heater must not be connected to the electricity supply via an external

switching device (such as a timer) or a circuit that is regularly switched on and o by

the utility supplier. Failure to follow this warning could result in the heater’s thermal

cut-o being inadvertently reset and could create a ﬁ re hazard. Cables/ﬂ exes that are

supplied pre-ﬁ tted to the product must NOT be extended.

CHILD SAFETY

WARNING

This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of appliance by a

person responsible for their safety.

This appliance can be used by children from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they

have been given supervision or instruction concerning use of the appliance. Children

shall not play with the appliance. Cleaning and user maintenance shall not be made by

children without supervision. Children of less than 3 years should be kept away unless

continuously supervised.

Children aged from 3 years and less than 8 years shall only switch on/o the appliance

provided that it has been placed or installed in its intended normal operating position

and they have been given supervision or instruction concerning use of the appliance

in a safe way and understand the hazards involved. Children aged from 3 years and

less than 8 years shall not plug in, regulate and clean the appliance or perform user

maintenance. This product contains a replaceable battery.

WARNING: KEEP BATTERIES OUT OF REACH OF CHILDREN.

WARNING: Packaging should be disposed o responsibly as the EPS could be a

potential choking hazard for children

This product meets the Ecodesign requirements for an electric ﬁxed local space heater. Commission Regulation

(EU) 2015/1188.

Energy Related Product Directive

Technical Details

Type of heat output/ room temperature control

With electronic room temperature control

Yes

Electronic room temperature control plus week timer

Yes

With open window detection

Yes

With adaptive start control

Yes

Model Identiﬁer(s): MFP050E MFP070E MFP100E MFP150E MFP200E

Norninal heat output Pnom 0.5kW 0.75kW 1 kW 1.5kW 2.0kW

Height (mm) 536 536 536 536 536

Width (mm) 503 503 671 741 911

Depth (mm) 104 104 104 104 104

Minimum heat

output (indicative) Pmin N.A N.A N.A N.A N.A

Maximum continuous

heat output Pmax,c 0.5 0.75 1 1.5 2

Auxiliary Electricity Consumption

At nominal heat output elmax 0.00 0.00 0.00 0.00 0.00

At minimum heat output elmin 0.00 0.00 0.00 0.00 0.00

In standby mode elSB <0.0005 <0.0005 <0.0005 <0.0005 <0.0005

With open window detection

Yes

With adaptive start control

Yes

Contact details

Glen Dimplex Heating and Ventilation

Millbrook House, Grange Drive, Hedge End, Southampton, SO30 2DF

Tel: 0344 879 3588

All Models

Controls

Digitally controlled, Electronic Thermostat accurate to (±0.2oC)

Timer modes:

7 Day Programmable User Timer, Out All Day, Home All Day, Away Mode

Continuous heat modes:

Eco, Manual, Frost Protect, Setback

Controller UI

• Open window detection, Adaptive-start

• Advance time period

• Adjustable max setpoint range (7-30°C)

• Bluetooth for software updates

• Child Lock & Landlord Lock (PIN-based)

Construction • Durable epoxy-polyester powder coated steel casing with louvered upward facing grille

• Advanced controls with capacitive sense technology for total ﬂexibility of heating

Colour/ Finish

Metal Chassis, Air Outlet Grille & Control Moulding - Trac White (RAL 9016)

Element Compact, ﬁnned, mineral ﬁlled sheathed element

Installation Wall bracket

Safety • Thermal cut-out. Auto reset type

• Overheat detection

IP Rating IP24

Battery

3.3V coin cell battery to backup real time clock. Battery life >5 years.

Supply

1.3 metres ﬁtted, 3 core for fused spur installation, 1/N/PE ~230-240 V, 50Hz

Class I, with earth wire

Approvals CE and BEAB

Warranty 2 years

Country of Origin United Kingdom

Manufacturer Glen Dimplex Heating & Ventilation

(GDC Group Ltd.)

WARNING:

This product is heavy and care

should be taken in installation

Please read the instructions closely before ﬁ rst using the product, there is also a quick-

start guide on page 8 if you need a reminder of how to use the basic functions in the

future. The heater is designed for wall mounting using the wall bracket supplied. It

should only be operated when in the upright position as shown - see Fig.3 and Fig.4.

All models are splash proof to IP24. Before connecting the heater check that the supply

voltage is the same as that stated on the heater.

MODEL A B C D E

MFP050E 390mm 150mm 503mm 536mm 104mm

MFP075E 390mm 150mm 503mm 536mm 104mm

MFP100E 560mm 150mm 671mm 536mm 104mm

MFP150E 630mm 150mm 741mm 536mm 104mm

MFP200E 800mm 150mm 911mm 536mm 104mm

255mm

‘B’

Minimum

mounting

clearance

Minimum mounting clearance

300mm

‘A’

General Information

Wall Mounting Instructions

Fig. 2

IMPORTANT - The wall bracket

supplied with the heater must

be used and the heater must

be installed in the correct

orientation. The ﬁ xings should

be used to secure the bracket to

the particular wall on which the

heater will be installed. The heater

should be positioned observing

the minimum clearances stated

around the heater - see Fig. 2,

Fig. 3 and Fig. 4.

‘C’ 150mm

(min)

150mm

(min)

150mm

(min)

‘D’

To mount the heater to the wall:

1. Remove wall mounting bracket from the back of the heater by depressing the spring

latch at the side of each bracket - see Fig.2.

2. Fix the wall bracket securely to the wall through the four screw holes. Ensure only

screw ﬁ ttings suitable for the particular wall type are used.

3. Present the heater to the wall bracket and engage bottom slots in the back with

bracket hooks.

4. Press the top of the heater into locked position and ensure the clips on the top are

engaged.

Minimum mounting clearance

300mm

(min) ‘E’

Shelf / Obstruction

Minimum front

clearance

*Please note correct product

orientation is with controller

facing top right side only

150mm

(min)

Fig. 3 Fig. 4

A setup wizard will display when the product is powered on for

the ﬁrst time. This will set the following:

• Time, Date, Daylight Savings Time

• Sound On/O

For information on using the Heaters controls, refer to page 12.

The Heater will then take the User to the Home Screen with the

‘Out All Day’ Timer Mode active.

First Time Power-On

Operation Manual

Important

During initial heat-up, some odour may be

emitted due to the newness of materials

used in manufacture. This is normal and will

disappear after a short period of use. It is

however advisable to keep the room well

ventilated.

The controls are located on top of the heater. This consists of a display screen and six touch sensitive buttons.

WARNING: FAILURE TO FOLLOW THESE OPERATING INSTRUCTIONS MAY RESULT IN INJURY AND/OR DAMAGE.

1Display Screen

2‘Menu’ Button

3‘Back’ Button

4‘Up and Down’ Arrows

5‘Enter’ Button

6‘Advance’ Button

7Heating Status

The heater is ﬁtted with an adjustable thermostat enabling the room temperature to be controlled. The minimum

room temperature is 7°C. The maximum temperature is set to 30°C. A temperature of 21°C is a common comfortable

room temperature.

Out All Day

57 3

2 46

21°C

Heating On

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dimplex Chauffage

Dimplex

Dimplex DTX Series Manuel d'instructions d'installation

Dimplex

Dimplex PFH30R Manuel utilisateur

Dimplex

Dimplex TAYLOR SUITE Manuel utilisateur

Dimplex

Dimplex ML Series Manuel utilisateur

Dimplex

Dimplex DHCERA15M Manuel utilisateur

Dimplex

Dimplex LC Series Manuel utilisateur

Dimplex

Dimplex DHCER24M Manuel utilisateur

Dimplex

Dimplex CH Series Manuel utilisateur

Dimplex

Dimplex FXPH1/42/750 Manuel utilisateur

Dimplex

Dimplex CFS120 Manuel utilisateur

Dimplex

Dimplex OCR15 Manuel utilisateur

Dimplex

Dimplex B075E Manuel utilisateur

Dimplex

Dimplex M2GTS Manuel utilisateur

Dimplex

Dimplex FX 20E IPX4 Manuel utilisateur

Dimplex

Dimplex H 260E Manuel utilisateur

Dimplex

Dimplex DXUF 20TN Manuel utilisateur

Dimplex

Dimplex DGWH4031 Manuel utilisateur

Dimplex

Dimplex THORNE & DERRICK AC6 Manuel utilisateur

Dimplex

Dimplex Longbourn LBN20 Manuel utilisateur

Dimplex

Dimplex CPH10 Manuel utilisateur

Dimplex

Dimplex PCH1000TCW Manuel utilisateur

Dimplex

Dimplex RD 1007 TS Manuel utilisateur

Dimplex

Dimplex CABR Manuel utilisateur

Dimplex

Dimplex RFV-800 "D" Series Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur