Dimplex EPX Manuel utilisateur

Quick Start Guide

EPX Panel Heater with RX24TI Programmer

EPX Panel Heater fitted with RX24TI Programmer

Issue 1 D1223-0106

This guide is for quick reference only. Refer to EPX/RX24TI installation and operating instructions for further information.

EPX panel heaters are fitted with an integral

thermostat and On/Off switch.

With the addition of an RX24TI timer, the

heater can be programmed to automatically

switch on/off at different times of the day.

The RX24TI is fitted by removing the plastic

cover adjacent to the thermostat and simply

slotting into place.

The RX24TI may be removed from the for

easy programming if required.

(A) Thermostat: slide the thermostat control to the appropri-

ate position to give comfort level required.

Heater will automatically switch on and off as necessary to

maintain the selected temperature. A higher setting will

make the room warmer.

(B) Power switch

(D) Heat indicator: Illuminates when the heater is delivering

heat

MODE selection

There are three different operating

modes. Press MODE to cycle

through these:

MAN OFF heating is permanently

off

MAN ON heating is permanently

on (cycles on thermostat)

AUTO operates the heating in

conjunction with the program

Glen Dimplex UK Ltd. Millbrook House, Hedge End, Southampton, SO30 2DF. For further assistance please contact Dimplex customer services on 0870 727 0101

BD C

RX24TI programmer set up

To program the RX24TI for the first time, it will need to be plugged

into the heater to charge up.

When operated in the heater, the display is lit (blue); this turns off

after a short period of inactivity.

When removed from the heater for programming, the display is not

lit.

Set the Time

Press the PROG key once to set

the time.

The symbol appears on the

screen.

Set the hours using the

keys. Press ENTER and repeat

the process to set the minutes.

When complete, press ENTER

again. The time is now set.

Set the daily program

Up to 4 program (on/off) periods

can be set for the 24 hour period.

Press PROG twice.

P1 ON is displayed, denoting the

first ON time setting.

Set the hours/minutes for the first

On period using the but-

tons, in the same way as for set-

ting time (above).

Note, the minutes are set in 10

minute blocks.

Once the P1 ON time is set, press ENTER and set the P1 OFF time

(i.e. the time at which the heater should switch off).

Repeat the procedure for P2 - P4 for as many on/off periods as

required.

If less than 4 on/off periods are needed, simply leave the unneeded

periods in their default setting.

After programming P4, the display automatically returns to the

default screen.

Example time program:

The example below explains how 4 time program periods can be

set up to allow the heater to operate at times when the room is

occupied.

P1 ON: 06:00 P2 ON: 11:00 P3 ON: 16:00 P4 ON: 00:00 (unused)

P1 OFF: 07:30 P2 OFF: 12:00 P3 OFF: 21:00 P4 OFF: 00:00 (unused)

Program Advance

Heater controls

When in AUTO mode, to “Advance” the program to the next time

block, press the button for 2 seconds.

“ADVANCE” appears on the display.

Press and hold for 2 seconds to cancel the program advance.

Table des matières

Autres manuels Dimplex Chauffage

Dimplex

Dimplex DTD2R05 Manuel utilisateur

Dimplex

Dimplex OFC2000 Manuel utilisateur

Dimplex

Dimplex CPH10 Manuel utilisateur

Dimplex

Dimplex RPX Series Manuel utilisateur

Dimplex

Dimplex XL12N Manuel utilisateur

Dimplex

Dimplex Studio G DXSTG25 Manuel utilisateur

Dimplex

Dimplex 5011139037800 Manuel utilisateur

Dimplex

Dimplex DGR32PLP Manuel utilisateur

Dimplex

Dimplex Winterwarm WWFH20E Manuel utilisateur

Dimplex

Dimplex MFP Series Manuel utilisateur

Dimplex

Dimplex PFH30E Manuel utilisateur

Dimplex

Dimplex PLX075NN Manuel utilisateur

Dimplex

Dimplex Q-Rad QRAD050RF Manuel utilisateur

Dimplex

Dimplex CXLS12N Manuel utilisateur

Dimplex

Dimplex ML2TS Manuel utilisateur

Dimplex

Dimplex QM050RF Manuel utilisateur

Dimplex

Dimplex AF6 Series Manuel utilisateur

Dimplex

Dimplex SRX 070 ECM Manuel utilisateur

Dimplex

Dimplex RX TI RB Manuel utilisateur

Dimplex

Dimplex TAYLOR SUITE Manuel utilisateur

Dimplex

Dimplex DGWH4031 Manuel d'instructions d'installation

Dimplex

Dimplex CMH Series Manuel utilisateur

Dimplex

Dimplex PLX 500 Manuel utilisateur

Dimplex

Dimplex Q-Rad Series Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur