Dimplex ARLWP800TI Manuel utilisateur

Dimplex Low Wattage Panel Heaters

Models: DXLWP400, DXLWP400TI,

DXLWP800, DXLWP800TI N & ARLWP800TI

Installation and Operating Instructions

Dimensions

(millimetres)

Models Specification

DXLWP400 400W Neon Heat Switch

DXLWP400TI 400W Neon Heat Switch / 24 Hour Timer

DXLWP800 800W Neon Heat Switch

DXLWP800TI N 800W Neon Heat Switch / 24 Hour Timer

ARLWP800TI 800W 2 Neon Heat Switches / 24 Hour Timer

THESE INSTRUCTIONS SHOULD BE READ CAREFULLYAND RETAINED FOR FUTURE REFERENCE

Electrical Connection

WARNING THIS APPLIANCE MUST BE EARTHED

If the socket outlets in your home are not of the 13 amp BS1363

type they will not accept the plug connected to this heater, therefore

cut off the plug. When cut off this plug can constitute a shock

hazard if inserted into a socket outlet. It must therefore be

disposed of safely.

Before wiring the appropriate plug please note that the wires in

this mains lead are coloured in accordance with the following

code.

GREEN/YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

Connect the Green/Yellow wire to the terminal marked Eor the

earth symbol or coloured Green or Green/Yellow.

Connect the Brown wire to the terminal marked Lor coloured

Red.

Connect the Blue wire to the terminal marked Nor coloured

Black.

DO NOT connect the Brown (Live) or the Blue (Neutral) wires to

the Earth terminal of your 13 amp plug. If the terminals of the

plug are unmarked or you are in any doubt, consult a qualified

electrician.

CAUTION: If you use this heater in conjunction with a thermal

control, programme controller, timer or any other device which

switches the heater on automatically observe all safety warnings

at all times.

600 mm - 400W

800 mm - 800W

500 mm

Important Safety Advice

WARNING –THIS APPLIANCE MUST NOT BE USED IN A

BATHROOM.

WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE

SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING

POOL.

WARNING – THIS HEATER MUST NOT BE LOCATED

IMMEDIATELY BELOWA FIXED SOCKET OUTLET.

The plug must be accessible after heater installation.

DO NOT USE THE HEATER UNTIL THE FEET OR WALL

BRACKETS ARE FITTED CORRECTLY.

FOLLOW these instructions carefully.

The heater carries a warning ‘DO NOT COVER’ to alert the

user to the risk of fire that exists if the heater is

accidentally covered.

Models DXLWP400TI, DXLWP800TIN and ARLWP800TI

can be set to switch on automatically. Remember to

observe all safety warnings at all times.

This appliance is not intended for use by children or other

persons without assistance or supervision if their

physical, sensory or mental capabilities prevent them

from using it safely. Children should be supervised to

ensure that they do not play with the appliance.

If young children, the aged or infirm are likely to be left in

the vicinity of the heater, we advise that adequate

precautions should be taken. We recommend a guard

be fitted to ensure contact with the heater is avoided and

objects cannot be inserted into the product.

If the mains lead is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified

person in order to avoid a hazard.

For further information, please contact our guard supplier

direct on Tel. No. 01603 667957, or in case of difficulty or

for further advice contact the Customer Helpline.

INDUKLWPRG Issue 6

Installation

The Fixing Kit should contain: 1 Drilling Template, 3 Screws, 3

Rawlplugs, 1 Mounting Bracket and 1 Hexagon Key.

Wall Mounted Operation (see Fig. 2)

Suggested Fixings

SOLID BRICK/BLOCK: No. 8 Rawlplug inserts, 6mm drill bit.

PLASTERBOARD: If possible locate studding and use No. 8

woodscrews directly into the wood, otherwise M5 rawlplug

intersets are suitable.

NOTE: FOR OTHER WALL TYPES (e.g. Timber frame and hollow

concrete) SEEK SPECIALIST ADVICE.

1. Select the position for the heater ensuring there is

clearance from any furniture and fittings of at least 150mm

above the heater, 50mm below and 25mm each side.

Curtains must not be closer than 150mm from the top of

theheater.

2. Position the drilling template provided on the wall ensuring

it is level. Mark the position of the relevant holes on the

wall at the edge of template. Before drilling check that the

distance between the hole centres is correct, 340mm for

400W Models and 540mm for 800W models (see Fig. 2).

130mm 340mm - 400W

540mm - 800W

95mm

150mm

50mm

420mm

25mm 25mm

130mm

Drilling Holes

Bracket

Fig. 2

Positioning the Heater

Select the position for the heater ensuring there is clearance

from any furniture and fittings of at least 150mm above the heater,

50mm below (wall mounted) and 25mm each side. Curtains

must not be closer than 150mm from the top of the heater.

Free Standing Operation (see Fig. 1)

NEVER USE THE HEATER FREE STANDING WITHOUT THE FEET

FITTED (FEET ARE PACKED SEPARATELY IN CARTON).

1. Lay the heater on its front.

2. Remove the two socket head screws from the base of

the heater using the hexagon key supplied.

3. Place feet over base of heater, align holes and engage

hook on foot into the recess on the back of the heater -

see Fig. 1.

4. Replace the screws but do not overtighten.

Fig. 1

Rear View

3. Drill the wall at the three marked positions and fit the wall

plugs.

Ensure template has been removed.

4. Fix two No. 8 screws to the top two holes leaving 3mm of

the screw exposed. Hang the heater on the screws.

5. Fit the bottom bracket, found in the fixing kit, in the slot at

the base of the heater and screw the bracket to the wall.

Test that the heater is now securely fixed to the wall.

Operation

IMPORTANT - OBJECTS OR CLOTHING MUST NOT BE PLACED

ON THIS HEATER.

Before using the heater ensure that all warnings and

instructions have been read carefully.

OPERATION - SINGLE RATED MODELS

Models DXLWP400, DXLWP400TI, DXLWP800, and

DXLWP800TI N

Turn the heater on using the switch on the right side of the heater

- the switch will be illuminated.

OPERATION - DUAL RATED MODEL - Model ARLWP800TI

The two switches on the side of the heater control the heat output.

Both switches illuminated indicates maximum output.

Top switch only illuminated indicates 500W output on 800W

model.

Bottom switch only illuminated indicates 300W output on 800W

model.

Note: on models fitted with a timer, at least one switch must be

illuminated for the heater to operate.

MODELS WITH TIMER - (see Fig. 3)

DXLWP400TI and DXLWP800TI N - 1 Switch,

The switch on the side of the heater turns the heater on.

Note: This switch must be in the “on” position before the heater

will operate.

ARLWP800TI - 2 Switches

The two switches on the side of the heater control the amount of

heat available as described above, (Operation - Dual Rated

Model).

NOTE: At least one switch must be in the ‘On’ position before the

heater will operate.

Models with Timer

DXLWP400TI, DXLWP800TI N & ARLWP800TI

Set the I- ¡¡

¡¡

¡- Oslide switch on the timer

(Fig. 3) to :

Position O - Heating Off

Position I - Manual operation

This setting allows power to the heater

uninterrupted by the timer settings. The

heat selector switch will control the output

(see ‘Using the heater’).

Position ¡¡

¡¡

¡- ‘Auto’ operation

DO NOT disconnect this heater from

the mains supply unless it is being

taken out of use (e.g. in summer or for

storage), otherwise the timer clock will

stop.

Setting the time of day

To set the time of day, rotate the timer

dial clockwise (indicated by the arrow)

until the correct time of day is opposite

the reference mark (see Fig. 4).

The 24-hour clock is used ; e.g. time shown for 3 pm is ‘15’

(15:00hrs).

Setting the ‘Auto’ ON and OFF times

To set the timer :

1. Using your finger tip or the tip of a

pencil, push in as many segments as

necessary around the dial, according

to the times you don’t require heat –

see Fig. 4. Each segment pushed in

switches the heater OFF for that part of

the hour. All other segments will be ON.

For example, Fig. 5 shows the timer

set to switch the heater ON between 7

am and 9 am and between 4 pm and

9.30 pm .

2. You can select as many ON periods

as you like, within the 24-hour day. The

settings will repeat every day until changed.

3. To change ON and OFF times, simply push in any ‘ON’

segments you wish to cancel and pull out new ‘ON’ segments

as required.

Switching to auto

Set the heat selector and thermostat for the heat output required.

Check that the clock shows the correct time of day. Set the I - ¡¡

¡¡

- O slide switch to ¡¡

¡¡

¡(see Fig. 4) - the convector will switch ON

and OFF according to the timer settings (see Fig 5).

IMPORTANT NOTES

Remember to observe all safety warnings when operating the

heater on auto setting unattended or attended .

If the mains supply to the heater is interrupted, the timer clock

will stop until power is restored ; reset the time of day to ensure

correct ON and OFF times.

Fig. 3

Fig. 4

Fig. 5

Cleaning

WARNING –ALWAYS DISCONNECT FROM THE POWER SUPPLY

BEFORE CLEANING THE HEATER.

Do not use detergents, abrasive cleaning powder or polish of

any kind on the body of the heater.

Allow the heater to cool, then wipe with a dry cloth to remove dust

and a damp cloth (not wet) to clean off stains. Be careful not to

allow moisture into the heater.

Recycling

For electrical products sold within the European Community.

At the end of the electrical products useful life it

should not be disposed of with household waste.

Please recycle where facilities exist. Check with

your Local Authority or retailer for recycling advice

in your country.

After Sales Service

Your product is guaranteed for three years from the date of

purchase.

Within this period, we undertake to repair or exchange this product

free of charge (subject to availability) provided it has been

installed and operated in accordance with these instructions.

Your rights under this guarantee are additional to your statutory

rights, which in turn are not affected by this guarantee.

Should you require after sales service you should contact our

customer services help desk on 0870 727 0101. It would assist

us if you can quote the model number, series, date of purchase,

and nature of the fault at the time of your call. The customer

services help desk will also be able to advise you should you

need to purchase any spares.

Please do not return a faulty product to us in the first instance as

this may result in loss or damage and delay in providing you with

a satisfactory service.

Please retain your receipt as proof of purchase.

Glen Dimplex UK Limited

Millbrook House

Grange Drive

Hedge End

Southampton

Hampshire. SO30 2DF

UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)

Customer Services: Tel. 0870 7270101

Fax. 0870 7270102

e-mail [email protected]

Republic of Ireland Tel. 01 8424833

[c] Glen Dimplex UK Limited

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and

EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dimplex Chauffage

Dimplex

Dimplex RPX075N Manuel utilisateur

Dimplex

Dimplex XT12 Manuel utilisateur

Dimplex

Dimplex QUBEFAN Q2BT Manuel utilisateur

Dimplex

Dimplex SOLAR ST0133 Manuel utilisateur

Dimplex

Dimplex AF12 Series Manuel utilisateur

Dimplex

Dimplex FW 550S Manuel utilisateur

Dimplex

Dimplex OFRC20TI Manuel utilisateur

Dimplex

Dimplex CFS60E Manuel utilisateur

Dimplex

Dimplex CXL N Instructions de montage

Dimplex

Dimplex EPX Series Manuel utilisateur

Dimplex

Dimplex RD 907 Manuel utilisateur

Dimplex

Dimplex PCH2000TCW Manuel utilisateur

Dimplex

Dimplex KSE 050 Manuel utilisateur

Dimplex

Dimplex 3071 Manuel utilisateur

Dimplex

Dimplex Saletto LPP050E Manuel utilisateur

Dimplex

Dimplex DYLP40 Manuel utilisateur

Dimplex

Dimplex Electric Unit Heaters Manuel utilisateur

Dimplex

Dimplex Duo300i Manuel utilisateur

Dimplex

Dimplex LC Series Manuel utilisateur

Dimplex

Dimplex CMH Series Manuel utilisateur

Dimplex

Dimplex RCH5031W Manuel utilisateur

Dimplex

Dimplex BK 1202 S Manuel utilisateur

Dimplex

Dimplex EF 12/20 TI Manuel utilisateur

Dimplex

Dimplex CVP1 Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur