Digitools DigiDirve-4 Series Manuel utilisateur
1
User Manual
DigiDirve-4.x
Document version: 20210822
Decoder software version 23 or higher
DigiDrive-4.1
DigiDrive-4.2
DigiDrive-4.5
2
Content
Főbb paraméterek: ..................................................... Hiba! A könyvjelző nem létezik.
A v23-as működtető szoftver általános jellemzői: ........................................................ 5
Bekötés:....................................................................... Hiba! A könyvjelző nem létezik.
DigiDrive-x.1: ............................................................................................................. 7
DigiDrive-x.2: ............................................................................................................. 8
DigiDrive-x.3: ............................................................................................................. 8
DigiDrive-x.5: ............................................................................................................. 9
Üzembe helyezés: ....................................................... Hiba! A könyvjelző nem létezik.
Motorvezérlő kimenet: ............................................ Hiba! A könyvjelző nem létezik.
A terhelés szabályzó beállítása: ............................... Hiba! A könyvjelző nem létezik.
Mozdony sebesség beállítása: .................................... Hiba! A könyvjelző nem létezik.
A 3 pontos sebesség görbe (CV29,4=0): .................. Hiba! A könyvjelző nem létezik.
A 28 pontos sebesség görbe (CV29,4=1): ................ Hiba! A könyvjelző nem létezik.
Sebesség alapjel szorzó: .......................................... Hiba! A könyvjelző nem létezik.
Gyorsítás lassítás beállítása: .................................... Hiba! A könyvjelző nem létezik.
Funkció kimenetek: ..................................................... Hiba! A könyvjelző nem létezik.
Funkció kimenetek regiszterei: ................................ Hiba! A könyvjelző nem létezik.
Funkciókimenet üzemmódjának és az alap „fényerő”-nek a beállítása: ................ 18
Egyéb funkciók: ........................................................... Hiba! A könyvjelző nem létezik.
Analóg mód: ............................................................. Hiba! A könyvjelző nem létezik.
Működés fékgenerátorral vezérelt szakaszon. ........................................................ 27
ABC mód: ................................................................................................................. 28
RailCom: ................................................................................................................... 30
Többmozdonyos üzem (consist mód): .................... Hiba! A könyvjelző nem létezik.
Szétcsatolás funkció: ............................................... Hiba! A könyvjelző nem létezik.
SUSI interfész: .......................................................... Hiba! A könyvjelző nem létezik.
Funkciógomb állapotának mentése: ....................... Hiba! A könyvjelző nem létezik.
Nehéz vonat funkció: ............................................... Hiba! A könyvjelző nem létezik.
Konfig regiszterek CV29, CV49: ............................................................................... 37
Programozás: .............................................................................................................. 38
ACK impulzus: .......................................................... Hiba! A könyvjelző nem létezik.
3
CV regiszterek alap állapotának visszaállítása, mentése: ..... Hiba! A könyvjelző nem
létezik.
A funkció gombok alap beállítása: ........................... Hiba! A könyvjelző nem létezik.
CV regiszterek: ............................................................................................................ 40
4
Thank you for choosing the product developed and produced by
the Hungarian DigiTools Electronics Ltd.
Key features:
o Communication according to NMRA DCC standard
o speed gear of 28, 128, programmable speed curve
o Addressed between 1-9999
o Max. 1 A motor output
o Load control (can be set in CV register)
o 18 kHz motor PWM frequency
o 4 pcs. (NEM651-652) or 10 pcs. (plux22) short circuit protected interface
(altigether max. 700 mA)
o Analogue mode
o Assymmetric DCC sign notice (ABC mode)
o Constant break path in ABC mode
o RailCom
o SUSI interface (only plux22)
o Consist (multitrain) mode
o Handling FL, F1-F28 functions
o Dimming function
o Shunting mode
o Switching on and off acceleration, deccelereation
o Driving function
o Car disconnection function
o 3 or 28 point speed curve setting
o o Different interfaces for the different standards
o Sizes:
▪ 10.5 * 16.5 * 4 mm (NEM651, NEM652)
▪ 15 * 18 * 4 mm (NEM658 PLUX22)
5
Overall features of v23 softvare:
The software of DigiDrive decoder family gained those functions that were
developed in DigiSound5 sound decoder. The new firmware can only be uploaded to
those DigiDrive softwars that are present in the market from 2015.
Changes in v23 version compared to v21 version:
- Standardizing the numbers and functions of CV registers.
- New function outputs and modes.
- Rewriting motor measuring.
- Rewriting PID regulator.
- Fault corrections.
It is essential if we update our decoder from earlier than v23 version it is necessary
to reset it before using it (CV8=0)!
It is banned to call back the saved CV settings!
6
Installing the Decoder:
Before installing the decoder it is reccommened to do as follows:
o if you are digitalizing your existing analogue system check if there is an
inte-grated buffer capacitor remained on the rail!
o o when digitalizing old, not prepared locomotives it is essential to
check if the value of the buffering capacitor is not higher than 47nF. If
there is no reactor coil between the motor and the decoder, do not leave
the capacitor on the output of the motor. Remove any capacitor
between the two motor leads and the frame,
o clean all the current collector skates and the wheels of the locomotive,
o run the motor starting from ~5-10V in neutral gear, while measuring the
cur-rent consumption. If it takes more than 200mA, check the state of
the motor brush and the commutator and if necessary sweep out the
coal powder from the gaps between the bites,
o check the light bulbs, if necessary change them into higher voltage ones.
The new bulbs should have at least 16V,
o check the insulations. In case of locomotives, where one of the poles of
the rail is the metal body itself it is important to check if the motor’s
insulation is adequate,
o check the condition of the engine in terms of running and lubrication.
The decoder is available with different interfaces according to the different
standards.
7
DigiDrive-x.1:
The outputs of the decoder have the standard NEM652 interface.
When attaching the decoder be careful to link the orange output of the interface to
pin 1 on the printed circuit, which is usually indicated with an asterisk.
In the event of an incorrect attachment, no damage is done, but the lighting
functions will nor work.
The standard length of the cable is 8 cm, but different cable lengths are available for
in-dividual orders.
8
DigiDrive-x.2:
The outputs of the decoder have the standard 6-pole NEM651 interface.
In the event of an incorrect attachment, no damage is done, but the locomotive
won’t work. In this case attach the dvice in the different direction.
DigiDrive-x.3:
The outputs of the decoder are being shipped with 8cm length of cables, without
interface.
This type is ideal for digitalizing old models which do not have printed circuit for mo-
tor.
The list below will help you attach the unit:
Orange: Right motor terminal
Yellow: Rear light
Green: AUX1 function output
Red: Right track connection
Grey: Left motor terminal
White: Headlight
Blue: Function interface. Common „+” pole
Black: Left track connection
Purple: AUX2 function output
9
DigiDrive-x.5:
The outputs of the decoder have standard NEM 658, PLUX22 interface.
The missing pin in the middle of the pin line is the „index” pin. On the preparatory
panel of the locomotive, the holes for this pin are omitted or marked separately.
Sizes: 15 mm x 18 mm x 4.0 mm
Index pin
10
Installation:
After having installed the decoder, check the position of the cables, they should not
be in the way of any moving or rotating part. If everything is fine, you may start the
voltage test.
Motor control interface:
The decoder can control one permanent magnetic commutator direct current motor.
The H bridge made of FET transistors continuously has maximum 1A current.
The load control frequency is 18kHz.
The output is short circuit protected.
The protection is guaranteed only in case of standard installation! If during
assembling or because of an incorrect installation a short circuit should occur, for
example, if one of the cables of the motor output (grey, orange) and the rail cables
(black, red) touch, this may result in damage in the decoder.
If the short circuit protection sign alarms the decoder can only be reinstalled after
the isolation of voltage.
Setting the load control:
The CV registers shown in the following chart belong to the motor speed control:
speed
control
Bit 7
(128)
Bit 6
(64)
Bit 5
(32)
Bit 4
(16)
Bit 3
(8)
Bit 2
(4)
Bit 1
(2)
Bit 0
(1)
CV51 Effect of load control in consist mode
CV52 Effect of load control in normal mode
CV54 Boosting the proportional part. Default value is 3.
CV55 Boosting the integrating part. Default value is 3.
CV56 Boosting the derivative part. Default value is 128.
CV49 *enable
PID.
*enable PID: enabling the operation of the load control
Ce manuel convient aux modèles suivants
3
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
