Digital Projection Titan 800 Manuel utilisateur
Atlanta, GA USA • Manchester, UK • Beijing, China • Singapore
770.420.1350 • www.digitalprojection.com
Quick Start Guide
TITAN 3D Displays
This guide applies to all 3D Titans of Producon Version F or higher.
Version F projectors can be
idened by inspecng
Input 8 for the new BNC type
Sync connectors.
3D displays
a. Plug in and power all devices.
b. Set the 3D source to output the desired resoluon.
c. Connect a BNC – BNC cable from the projector’s Sync Out to the Sync IR Emier.
d. Connect an “HDMI to DVI” cable from the source to the projector.
The HDMI Cable length should not exceed 50. If “Sparkles”, digital noise, or missing picture occurs, then use a shorter cable, replace it with
a higher quality cable, or consider a HDMI Extender. HDMI to DVI adaptors are not recommended since they aenuate and can degrade the
signal. Also, even short cables may result in image arfacts if they are of poor quality.
Note – Although it is not visible from the Input 8 Panel, the projector’s DVI connecon incorporates an HDMI 1.4a Receiver. To connect to
the HDMI 1.4a receiver, the “Sub” DVI connector on Input 8 must be used. The DVI “Sub” connector is the only connecon with an HDMI
1.4a receiver.
• Use the “Sub” connector on Input 8 if your 3D content is provided by Consumer 3D sources, such as a 3D Blu-Ray player or cable /
satellite tuners with 3D capabilies.
• Use the “Main” connector on Input 8 if computers serve as your 3D sources, and their output is sequenal video at high frame rates,
such as 120 Hz.
• Use both “Main” and “Sub” if the output of your 3D source is “Dual Pipe”, which is delivered via disnct le and right eye cables.
Special Consideraons for Placement of the 3D IR Emier
• Special consideraon should be taken when installing the 3D IR Emier. It should be either located at the screen poinng towards
the viewer, or it should be placed near the projector poinng toward the screen. Tesng should be done to ensure the IR sync
pulses are reected back to the viewer’s 3D glasses. The 3D glasses will not operate properly if they do not receive the IR sync
pulses.
• When the 3D IR Emier is acve, it is very important to note that the IR emission or “blast” may “jam” the IR receivers of local
electronic devices that are in direct line of site with the emier. If the IR blast from the 3D emier jams the IR receiver on the
projector, the projector may not funcon properly and control via the wireless remote control and the built-in keypad may be
disrupted. Therefore, for 3D applicaons with IR emiers, we recommended the use of control via Serial or IP based control
devices. When controlling the projector via Serial or IP based devices, the projector’s IR receivers should be disabled by plugging a
3.5mm mini connector into the hardwire input, or by covering the IR receivers with opaque material.
• If it is not possible to employ Serial or IP control of the projector, and the IR receivers in the projector are being overloaded or
jammed by the 3D IR emier, we recommend employing a hardwire connecon between the remote control and the projector.
Connecng the 3.5mm hard-wire cable will disable the IR receivers on the projector.
• When nished with 3D viewing, and switching back to 2D, the projector’s 3D Mode should be reset to the “O” posion. This will
turn o the 3D IR emier, and it will prevent any 2D content from possibly being displayed with 3D sengs.
Quick Start Guide
TITAN 3D Displays
Connect the Components
1
a. Set the projector’s 3D Mode in the 3D menu. Go to : Menu / Setup / 3D
Press the le and right arrows to select 3D Mode. Press the up and t arrows to select.
Possible 3D Modes include:
• O – 3D circuitry is turned o. No 3D imagery will be displayed.
• Professional – All opons will be available for adjustment.
• Consumer – 3D Input Assign, 3D Format and Output Shuering will be unavailable.
The following comments will help you determine which 3D Mode is appropriate for your applicaon:
• In Professional mode, all 3D formats, including Side by Side 1080p60, Frame Sequenal and Dual-Pipe can be used. It is important
to note that Frame Sequenal must use the “Main” DVI connector on Input 8 if the vercal frame rate of the source is greater than 60hz.
• In Consumer mode, the projector will automacally detect the following common 3D standards on Input 8:
Frame Packing : 2205p24, 720p50, 720p60 Side by Side : 1080i60, 1080p24
Frame Sequenal – 1080p
3D Input Assign - Select the desired Input. The choices are Input 3 and Input 8. Please note that this seng is not available in Consumer
Mode:
• Input 3: This input can be used in Professional Mode and is appropriate for standard bandwidth 3D source that do not require HDMI
1.4a compability, but do require ulizaon of the projector’s internal scaling. Input 3 is not recommended for consumer 3D applicaons.
• Input 8: Recommended for both Consumer and Professional 3D applicaons, the “sub” connector on this input incorporates the
HDMI 1.4a receiver. In addion, this input also provides the ability to accept high frame rate 3D signals and Dual Pipe signals, as
might be used in more crical Professional applicaons.
Please note – Input 8 does not provide image scaling. Therefore, if the nave resoluon of the source is something other than the
projector’s nave resoluon, an external scaler should be used if full display resoluon is desired. An external scaler is also required
when using an anamorphic lens in combinaon with a source connected to input 8.
Understanding and Selecting your 3D Mode
Dening your 3D Settings
Quick Start Guide
TITAN 3D Displays
2
3
3D Format – Select from Frame Packing, Side-By-Side (Half), Sequenal, Top-And-Boom, or Dual Pipe, as appropriate for your 3D source.
Please note, this seng is not available in Consumer Mode, as the 3D format is automacally detected by the HDMI 1.4a receiver.
Dark Time – Image Ghosng can be caused by the le-eye and right-eye images overlapping during the me that the Z screen or 3D glasses
are switching. Set the Dark Time to a value appropriate for the glasses or Z-screen. Try 1000 μS. Opmizing the Dark Time seng and 3D Sync
Delay (detailed below) will help to minimize ghosng.
Frame Dominance – The 3D frames are presented to the projector in pairs, and for proper viewing, the dominant frame needs to be present-
ed on-screen rst. Set Frame Dominance to match the incoming 3D video frame sequence. If the 3D content is uncomfortable to view, Frame
Dominance may be set incorrectly.
3D Sync Delay – The sync signal from the 3D source will be “in phase” with the frames generated by its graphics processor. To compensate for
processing delays in the projector, the 3D Sync Delay control is provided to introduce a delay to the sync output signal sent to the Z-Screen or
3D glasses. Adjust the Sync Delay me to minimize ghosng and achieve a smooth grey-scale.
3D Sync Source – Whenever possible, select “External”. In general, you should only select “internal” if your 3D source does not generate 3D sync.
3D Sync Output Polarity – Toggle this seng if the le-eye and right-eye images appear to be swapped.
Output Shuering (Frame Rate Mulplicaon) – If the 3D content is only available from the source at low frame rates, it will be necessary to
mulply the frame rate to reduce image icker. For example, a 60Hz 3D frame rate (30 Hz per eye) can be doubled to 120Hz (60 Hz per eye),
or a 48Hz 3D frame rate (24 Hz per eye) can be tripled to 144Hz (72 Hz per eye). Please note, this seng is not available in Consumer Mode,
as output shuering is automacally set based on the format detected by the HDMI 1.4a receiver.
Atlanta, GA USA • Manchester, UK • Beijing, China • Singapore
770.420.1350 • www.digitalprojection.com
a) If there is no 3D image present, then using the projector’s menu, verify that the signal is being received from the Source. If it is
present, the resoluon will appear in the “Source Informaon”. If it is not, check the sources output sengs, any processors in the
path, and the cabling.
b) If any digital noise or arfacts are present in the image, then test and verify the quality of the HDMI to DVI cable. If other external
devices or extenders are suspected, bypass each and then test again.
c) If the Output Shuering is set too high for the selected source, then the vercal size will be compressed.
d) If the 3D format is not automacally detected when in Consumer Mode, then change the 3D Mode to Professional, and manually
select the 3D Input, the 3D Format, and the 3D Output Shuering. Go to : Menu / Informaon / Source Informaon.
Troubleshooting
4
Quick Start Guide
TITAN 3D Displays
Dening your 3D Settings (continued)
3
Table des matières
Autres manuels Digital Projection Projecteur
Digital Projection
Digital Projection TITAN WUXGA Quad 3D Manuel utilisateur
Digital Projection
Digital Projection HIGHlite 660 3D Series Manuel utilisateur
Digital Projection
Digital Projection INSIGHT 4K Dual LED Series Manuel d'utilisation
Digital Projection
Digital Projection M-Vision Cine 320 3D series Manuel utilisateur
Digital Projection
Digital Projection TITAN sx+ Dual 3D Ultra Contrast Manuel utilisateur
Digital Projection
Digital Projection Titan Super Quad Manuel utilisateur
Digital Projection
Digital Projection TITAN sx+-500 Manuel utilisateur
Digital Projection
Digital Projection THUNDER 9000gv Manuel utilisateur
Digital Projection
Digital Projection Insight Laser 4K Manuel utilisateur
Digital Projection
Digital Projection HIGlite 8000 Series Manuel utilisateur
Digital Projection
Digital Projection POWER 2v Manuel utilisateur
Digital Projection
Digital Projection E-Vision 6000 Series Manuel utilisateur
Digital Projection
Digital Projection 4500 WUXGA Manuel utilisateur
Digital Projection
Digital Projection HIGHlite Series Manuel utilisateur
Digital Projection
Digital Projection TITAN WUXGADual3 D Manuel utilisateur
Digital Projection
Digital Projection Lightning 30sx+m Manuel utilisateur
Digital Projection
Digital Projection 35HD-T Manuel utilisateur
Digital Projection
Digital Projection Mercury Quad Series Manuel utilisateur
Digital Projection
Digital Projection E-Vision Series Manuel utilisateur
Digital Projection
Digital Projection INSIGHT 4K Quad Series Manuel utilisateur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
