Digital Projection Titan 800 3D series Manuel utilisateur

Rev A June 2012

USER GUIDES

INSTALLATION AND QUICK-START GUIDE

CONNECTION GUIDE

OPERATING GUIDE

113-083A

Titan 800 3D series

High Brightness Digital Video Projector

BOOK CONTENTS

About these Guides

Symbols used in these guides

Warnings

Notes

Product revision

Digital Projection Titan 800 3D series ABOUT THESE GUIDES

Rev A June 2012

About these Guides

Please read this guide carefully before using the projector, and keep it handy for future reference.

A serial number is located on the back of the projector. Record it here:

Symbols used in these guides

Warnings

ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely

followed.

WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless

the instructions are closely followed.

Notes

NOTE: this symbol indicates that there is some important information that you should read.

Product revision

Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features

without prior notice. Projectors built prior to this revision of the Operating Guide may therefore not include all the features described.

Rev A June 2012

Titan 800 3D series

High Brightness Digital Video Projector

INSTALLATION AND QUICK-START GUIDE

BOOK CONTENTS

INSTALLATION AND QUICK-

START GUIDE

What’s in the Box?

Getting to Know the Projector

Front and rear views

Remote control

Control panel indicators

Connection panel indicators

Digital Projection Titan 800 3D series CONTENTS Installation and Quick-Start Guide

Rev A June 2012

CONTENTS

What’s in the Box?...............................................................................Inst_1

Getting to Know the Projector....................................................Inst_2

Front and rear views .............................................................................Inst_2

Remote control......................................................................................Inst_2

Control panel indicators.......................................................................Inst_3

Connection panel indicators................................................................Inst_3

Positioning the Screen and Projector....................................Inst_4

Chassis adjustment ..............................................................................Inst_4

Fitting and adjusting the optional Rigging Frame .............................Inst_4

Fitting the Lens .....................................................................................Inst_5

Operating the Projector...................................................................Inst_6

Switching the Projector On ..................................................................Inst_6

Selecting an Input Signal or Test Pattern ...........................................Inst_6

Input signal....................................................................................Inst_6

Test pattern ...................................................................................Inst_6

Adjusting the Lens and Image .............................................................Inst_7

Zoom.............................................................................................Inst_7

Focus ............................................................................................Inst_7

Shift...............................................................................................Inst_7

Picture...........................................................................................Inst_7

Switching the Projector Off..................................................................Inst_7

Digital Projection Titan 800 3D series WHAT'S IN THE BOX? Installation and Quick-Start Guide

Page Inst_1Rev A June 2012

What’s in the Box? Notes

Make sure your box contains

everything listed. If any pieces are

missing, contact your dealer.

You should save the original box

and packing materials, in case you

ever need to ship your Projector.

Only one power cable - dependent

on the destination territory - will be

supplied with the projector.

Remote control

(105-023)

4x AAA batteries

User Guides on CD

(112-659) Important Information

(112-658)

Power cable, United Kingdom

(112-000)

Power cable, Europe

(112-001)

Power cable, North America

(112-002)

Projector

Remote cable

(102-162)

Digital Projection Titan 800 3D series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide

Page Inst_2Rev A June 2012

Getting to Know the Projector

Front and rear views

Notes

The projector uses the standard

Digital Projection infra-red remote

control.

Only the controls shown highlighted

are used on this projector.

For full details of how to use the

controls and the menu system, see

the Operating Guide.

Lens

Air

outlets

Air

inlets

Side

Connection

panel

Mains

input

Control

panel

Adjustable

feet

Front

infra-red

window

Rear

infra-red

window

(on

connection

panel)

Remote control

Infra-red

reception

40°

Transmit

indicator

Remote

control

backlight

On/Off

Rear

Connection

panel

Air lters

(behind panel)

Digital Projection Titan 800 3D series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide

Page Inst_3Rev A June 2012

Control panel indicators

The indicators on the control panel are as follows:

Power off = NO POWER

green = normal RUNNING mode amber = STANDBY mode

Shutter amber = CLOSED green = OPEN

Notes

Only the controls shown highlighted

are used on this projector.

For full details of how to use the

controls and the menu system, see

the Operating Guide.

For more information about

the connection panels, see the

Connection Guide.

Connection panel indicators

The indicators on the rear connection panel are as follows:

All on = Power-On Self Test

Lamps 1-2 off = OFF

green = ON (100%) amber = (80 - 99%)

ashing green = WARM-UP ashing amber = COOL-DOWN

red (projector in standby) = Lamp Comms Error (call service)

red (projector on) = Ballast Comms Error (call service)

ashing red (projector in standby) = Lamp Error on previous operation

ashing red (projector on) = Lamp / Interlock Error

Error ashing = Fan / System Error steady = Voltage Error

IR blue ash = Remote control command received

Inputs The indicators next to the input connectors on both panels are as follows:

off = not selected

green = input selected, signal detected, and in range

ashing green = input selected, but signal not detected or out of range

Power Shutter

Lamps

1 2

Error

Rear Connection Panel Side Connection Panel

Digital Projection Titan 800 3D series POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide

Page Inst_4Rev A June 2012

Notes

Always allow the projector

to cool for 5 minutes before

disconnecting the power or

moving the projector.

Ensure that there is at least

30cm (12in) of space between the

ventilation outlets and any wall,

and 10cm (4in) on all other sides.

Do not stack more than 3

projectors.

Do not place heavy objects on top

of the projector chassis. Only the

chassis corners and the rigging

frame are capable of withstanding

the weight of another projector.

Do not place the projector with its

front panel down on a surface, as

this may damage the lens or the

lens release lever.

Backup safety chains or wires

should always be used with

ceiling mount installations.

Do not tilt the projector more

than ±12° in either direction, in

desktop or ceiling mode, when in

use, as this may cause serious

lamp failure, damage the lamp

module and cause extra cost on

replacement.

±12°±12°

±12°±12° Ceiling

Desktop

Positioning the Screen and Projector

• Install the screen, ensuring that it is in the best position for viewing by your audience.

• Position the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen.

Chassis adjustment

• If the projector is to be operated from a at surface such as a projector table, then adjustment of projector level should be made by

turning the four feet under the chassis. Set the adjustable feet so that the projector is level, and perpendicular to the sceen.

Fitting and adjusting the optional Rigging Frame

• Remove the four adjustable feet.

• Secure the rigging frame to the projector, as shown below, making sure that the cable

attachments are at the top. Three screws secure each of the adjuster brackets to a

corner handle.

• To adjust the pitch, turn either the front pair or the rear pair of vertical adjusters, taking

care to turn both adjusters by the same amount.

• To adjust the roll, turn either the left pair or the right pair of vertical adjusters, taking care

to turn both adjusters by the same amount.

• To adjust the yaw, turn the single horizontal adjuster at the front.

Fixing

screws

Pitch Roll Yaw

Horizontal

adjuster

Vertical

adjusters

Frame

couplings

Digital Projection Titan 800 3D series FITTING THE LENS Installation and Quick-Start Guide

Page Inst_5Rev A June 2012

Fitting the Lens

• Turn the lens release lever clockwise so

that it is pointing upwards, to open the

lock fully.

• Remove the rear lens cap from the lens.

• Insert the lens into the lens aperture,

making sure that the plug on the zoom

drive mechanism lines up with the

socket on the front of the projector, then

push the lens in rmly as far as it will go.

Notes

Always allow the lamp to cool for

5 minutes before:

- disconnecting the power

- moving the projector

The lens release lever should

always be set to the locked

position to prevent the lens from

falling out.

Do not place the projector with its

front panel down on a surface, as

this may damage the lens or the

lens release lever.

Lens

release

lever

• Turn the lens release lever anti-

clockwise to the mid-position.

• The lens can now be pushed in further.

Push the lens in rmly as far as it will

go.

• Turn the lens release lever fully

anti-clockwise so that it is pointing

downwards, to close the lock fully.

Digital Projection Titan 800 3D series OPERATING THE PROJECTOR Installation and Quick-Start Guide

Page Inst_6Rev A June 2012

Operating the Projector

Switching the Projector On

• Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.

• Wait until the self-test has completed and the standby indicator on the projector control panel shows amber. The lamp will be off and the

projector will be in STANDBY mode.

• Press on the remote control or the control panel and hold for 3 seconds, to switch the projector ON. The power indicator on the

control panel will show green, the lamp will light and the shutter will open.

Selecting an Input Signal or Test Pattern

Input signal

• Connect an image source to the projector. The signal should be automatically detected by the

projector, and should be displayed within a two or three seconds.

If more than one signal is connected, then select the image you want to display:

• Press one of the Input buttons, to on the remote control, or

• Open the Main Menu, by pressing .

• Select from the Input Selection menu, using the and buttons.

Test pattern

If you have no image source connected to the projector, then you can display a test pattern instead:

• Open the Main Menu, by pressing .

• Select Test Pattern from the Input Selection menu, using the and buttons.

• Select a pattern from the Test Pattern menu, using the and buttons.

• Close the Main Menu, by pressing again.

Notes

For full details of how to use the

controls and the menu system, see

the Operating Guide.

Table des matières

Autres manuels Digital Projection Projecteur

Digital Projection

Digital Projection HIGHlite Laser 4K Series Manuel utilisateur

Digital Projection

Digital Projection MERCURY 5000HD Manuel utilisateur

Digital Projection

Digital Projection iVision50-series Manuel utilisateur

Digital Projection

Digital Projection Titan Pro Series III Manuel utilisateur

Digital Projection

Digital Projection M-Vision Cine 320 Series Manuel utilisateur

Digital Projection

Digital Projection TITAN sx+-500 Manuel utilisateur

Digital Projection

Digital Projection TITAN sx+600 Manuel utilisateur

Digital Projection

Digital Projection TITAN WUXGADual3 D Manuel utilisateur

Digital Projection

Digital Projection M-Vision Cine 3D series Manuel utilisateur

Digital Projection

Digital Projection dVision 30 Manuel utilisateur

Digital Projection

Digital Projection MERCURY 5000gv Manuel utilisateur

Digital Projection

Digital Projection E-Vision Series Manuel utilisateur

Digital Projection

Digital Projection E-Vision Laser 15000 Series Fiche technique

Digital Projection

Digital Projection 119-712B Manuel utilisateur

Digital Projection

Digital Projection M-Vision Laser 21000 WU Manuel d'utilisation

Digital Projection

Digital Projection HIGHlite Cine 330 3D Series Manuel utilisateur

Digital Projection

Digital Projection 8K Series Manuel utilisateur

Digital Projection

Digital Projection TITAN sx+-500 Manuel utilisateur

Digital Projection

Digital Projection Titan 930 Manuel utilisateur

Digital Projection

Digital Projection E-Vision 6900 Series Manuel utilisateur

Digital Projection

Digital Projection dVision 30sx+ Manuel utilisateur

Digital Projection

Digital Projection TITAN WUXGA Quad 3D Manuel utilisateur

Digital Projection

Digital Projection HIGHlite 660 Series Manuel utilisateur

Digital Projection

Digital Projection MERCURY 5000HD Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur