Digital Projection IVision50-series Manuel utilisateur

an introducon to

the projector

iVision50-series

User Manual

english

Contents of this User Manual

1 Introduction 7

1.1 Thank you

1.2 Training

1.3 Symbols used in this documentation

2 Safety and compliance 9

2.1 General safety considerations

2.2 Information/Warning - Potential Mercury Vapour Health Issues

2.3 FCC compliance

2.4 Disposal information

2.4.1 Statement WEEE (Waste Electrical and Electronic Equipment)

2.4.2 Disposal of batteries in the product

2.4.3 Turkey RoHS compliance

2.5 Service

3 What’s in the box? 13

4 Installation 15

4.1 System considerations

4.2 Ventilation

4.2.1 Ventilation accessories

4.3 Ceiling and rig mounting

4.4 Locking the projector

4.5 Projector angle (tilt)

4.6 Selecting a lens

4.6.1 Inserting a lens

4.6.2 Changing/removing a lens

4.6.3 Lens range

4.7 Lens lock

4.8 Lens shift

4.9 Lens planarity (Scheimpﬂug adjustment)

4.10 Zoom, focus and iris

4.11 Making the connections

4.12 Connecting video and data sources

4.13 Connecting control interfaces

4.14 Source format integrity – EDID

4.15 Image sizes

4iVision50-series

User Manual - Introduction

english

5 Overview 25

5.1 Keypad and indicator

5.2 Wireless remote control

5.3 Connectors

5.3.1 Signal connectors

5.3.2 Control connectors

5.4 Menu system

5.4.1 Top menu

5.5 3D main menu

5.5.1 3D > Dual head setup sub menu

5.6 Picture main menu

5.6.1 Picture > ColorMax sub menu

5.6.2 Picture > Advanced sub menu

5.7 Installation main menu

5.7.1 Installation > EDID sub menu

5.7.2 Installation > Synchronization sub menu

5.8 Settings menu

5.8.1 Settings > Pin Code sub menu

5.8.2 Settings > Network sub menu

5.8.3 Settings > Factory Reset sub menu

5.8.4 Settings > Service sub menu

5.9 Languages menu

5.10 Status menu

5.10.1 Status > Source Information sub menu

5.10.2 Status > Source Information > Advanced sub menu

5.10.3 Status > Source Synchronisation sub menu

6 Functionality 49

6.1 Powering On and Off

6.1.1 Manual power control

6.1.2 DPMS - power down

6.2 Image alignment

6.2.1 Image orientation

6.3 Language

6.4 System status

6.5 Lamp power

6.6 Source selection, source scan

6.7 On screen display (OSD) messages

6.7.1 Disabling the STATUS indicator

6.7.2 Setting the background color

6.7.3 Setting OSD menu timeout

6.7.4 Selecting the startup logo

6.8 PIN code

6.9 Disabling the wireless remote control (IR) receivers

6.10 Software upgrades

english

7 Optimising the image 53

7.1 Calibration data

7.1.1 Updating ColorMax calibration data

7.1.2 ColorMax modes

7.2 Setting a white point or color temperature

7.2.1 Deﬁning the system color gamut

7.3 Gamma

8 Technical speciﬁcations 61

9 Lamp change 63

6iVision50-series

User Manual - Introduction

english

1 Introduction

1.1 Thank you

Thank you for purchasing this projector.

When referring to the term xVision50 in this document,iit means that the content is applicable

for the following DPI products:

• iVision50 HD (1920x1080)

• iVision50 WUXGA (1920x1200)

• iVision50 PN (2560x1080)

The iVision50 series projectors set an industry benchmark for projectors in its size and

performance category. Featuring high resolution DLP-technology, high performance optics

and lenses, updated signal processing and built-in frame-lock synchronisation makes it the

ideal projector for multi-channel visualisation and simulation applications, where realism and

reliability are key criteria. In addition the excellent image performance it is capable of Active

Stereo 3D.

1.2 Training

To get the best performance out of the projector as well as the system, training is highly

advised, in addition to studying this user guide. Various courses are available. At the

Academy, skilled trainers will teach you basic projector use as well as more advanced set-up

and conﬁguration across multiple application areas. Go to www.digitalprojection.com.

1.3 Symbols used in this documentation

WARNING: Used to point out potential danger to people or equipment when using this

product or peripheral equipment under certain circumstances.

NOTE: Used to point out essential handling requirements for the projector, which if not

followed may cause product malfunctioning.

TIP: Used to give advice which beneﬁts the projector usage or conditions related to

projector performance.

The speciﬁcations and functionality of this projector may change without prior notice.

Features in the user guide pictures/drawings or text may be different from your

projector depending on model/version.

8iVision50-series

User Manual - Introduction

english

2 Safety and compliance

2.1 General safety considerations

• Use only the cables and cords supplied with the projector or original replacement

cables. Using other cables or cords may lead to malfunction and permanent damage to

the unit.

• Always use 3-prong (grounded) power cord to ensure proper grounding of the unit.

Never use 2-prong power cords, as this is dangerous and could lead to electrical shock.

• Never open the unit. The projector contains no user serviceable parts. Refer all repairs to

qualiﬁed personnel only. Make sure that no objects enter into the vents and openings of

the set.

• Do not spill any liquids on the projector or into the vents or openings of the unit.

• Always remove lens cap before switching on the projector. If the lens cap is not re-

moved, it may melt due to the high energy light emitted through the lens. Melting the

lens cap may permanently damage the surface of the projection lens.

• Do not look into the projection lens when the projector is switched on. The strong light

may permanently damage sight.

• Only place the projector on a stable surface, or mount it securely using an approved

ceiling-mount.

• Do not drop the projector.

• Always operate the projector according to the rotation guidelines. Operating the unit in

other positions may reduce lamp life signiﬁcantly, and may lead to overheating, resulting

in malfunctioning.

• Always allow ample airﬂow through the projector. Never block any of the air vents. Never

cover the unit in any way while running. Allow for sufﬁcient distance to walls and ceilings

to avoid overheating.

• Minimum safety distance to any side of the unit is 50cm / 20” in any direction (15 cm/ 6”

to ceiling).

• Hot air is exhausted from the rear vent. Do not place objects that are sensitive to heat

nearer than 50cm / 20” to the exhaust vent.

• The projector is designed for indoor use only. Never operate the unit outdoors.

• Do not operate the projector outside its temperature and humidity speciﬁcations, as this

may result in overheating and malfunctioning.

• Only connect the projector to signal sources and voltages as described in the technical

speciﬁcation. Connecting to unspeciﬁed signal sources or voltages may lead to malfunc-

tion and permanent damage of the unit.

• In order to prevent damage to the projector caused by over-voltages (e.g. lightning), we

recommend connection to a line (mains) circuit which has over voltage protection.

• Allow lamp to cool down for at least 60 minutes before changing.

USE ONLY ORIGINAL LAMPS.

• Connecting sources to a powered projector may result in product failure. It is recom-

mended that the power cable connector (projector-end) or the mains power socket is

accessible whilst the product is in use to enable mains power to be disconnected or

switched off when connecting source devices. This should be considered during product

installation.

10iVision50-series

User Manual - Safety and compliance

english

2.2 Information/Warning - Potential Mercury Vapour Health Issues

This projector uses a very powerful UHP™ lamp for illumination to produce an extremely

bright image.

This technology is similar to other high-pressure discharge lamps that are extensively used in

cars, street lights and other lighting appliances today. These lamps, like ﬂuorescent lighting,

contain small amounts of mercury. The amount of mercury present in a lamp is far below the

limits of danger set by the authorities. It is very important that lamps containing mercury are

treated properly to minimize potential health hazards.

The UHP™ lamp, like any other high brightness projector lamp, is under high-pressure when

operating. While the lamp and the projector are carefully designed to minimize the probability

of lamp rupture, the lamp may break while operating and small amounts of mercury va-

pour may be emitted from the projector. The probability of rupture increases when the lamp

reaches its nominal life. It is therefore highly recommended that the lamp is replaced when

the rated lifetime is reached.

As a general precaution, secure good ventilation in the room when operating the projector. If

lamp rupture occurs, evacuate the room and secure good ventilation. Children and pregnant

women in particular should leave the room.

When replacing a worn lamp, dispose of the used lamp carefully by proper recycling.

Mercury is a naturally occurring, stable metallic element that may pose a safety risk to people

under certain conditions. According to the Public Health Statement for Mercury published by

the Agency for Toxic Substances and Disease Registry (“ATSDR”, part of the United States

Public Health Service), the brain, central nervous system and kidneys are sensitive to the

effects of mercury, and permanent damage can occur at sufﬁciently high levels of exposure.

Acute exposure to high concentrations of mercury vapour can cause conditions such as

lung and airway irritation, tightness in the chest, a burning sensation in the lungs, coughing,

nausea, vomiting and diarrhoea. Children and fetuses are particularly sensitive to the harmful

effects of metallic mercury to the nervous system.

Seek medical attention if any of the above symptoms are experienced or if other unusual

conditions are experienced following lamp rupture.

This product contains chemicals, including lead, known to the State of California to

cause birth defects or other reproductive harm. Recycle properly; do not dispose of in

ordinary waste!

2.3 FCC compliance

FCC regulations state that changes or modiﬁcations not expressly approved by the party

responsible manufacturer could void your authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digi-

tal device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

CANADA

This Class A digital apparatus complies with Canadian ICES-003. / Cet appareil numérique

de la classe A est conforme à la norme NMB- 003 du Canada.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Digital Projection Projecteur

Digital Projection

Digital Projection Titan series Manuel utilisateur

Digital Projection

Digital Projection Vision 30 Series Manuel utilisateur

Digital Projection

Digital Projection Titan HD-500 Manuel utilisateur

Digital Projection

Digital Projection dVision 30sx+ Manuel utilisateur

Digital Projection

Digital Projection SHOWlite 6000gv Manuel utilisateur

Digital Projection

Digital Projection 8K Series Manuel utilisateur

Digital Projection

Digital Projection Titan 930 Manuel utilisateur

Digital Projection

Digital Projection LIGHTNING 35HD Manuel utilisateur

Digital Projection

Digital Projection E-Vision 6000 Series Manuel utilisateur

Digital Projection

Digital Projection E-Vision Laser WQ120 Series Manuel utilisateur

Digital Projection

Digital Projection TITAN SX+ 500 Manuel utilisateur

Digital Projection

Digital Projection THUNDER 9000gv Manuel utilisateur

Digital Projection

Digital Projection Lightning 30sx+m Manuel utilisateur

Digital Projection

Digital Projection Mercury HD Manuel utilisateur

Digital Projection

Digital Projection Highlite Cine 260 Manuel utilisateur

Digital Projection

Digital Projection morpheus 7000hdi Manuel utilisateur

Digital Projection

Digital Projection iVision Manuel utilisateur

Digital Projection

Digital Projection M-Vision Cine 230 Manuel utilisateur

Digital Projection

Digital Projection E-Vision Laser 5000 XGA Manuel utilisateur

Digital Projection

Digital Projection E-Vision Laser 6500 Series Manuel utilisateur

Digital Projection

Digital Projection Insight Laser 4K Manuel utilisateur

Digital Projection

Digital Projection HIGHlite 12000Dsx+ Manuel utilisateur

Digital Projection

Digital Projection dVision Scope 1080p Manuel utilisateur

Digital Projection

Digital Projection M-Vision 1080p-260 series Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Digital Projection iVision50-series Manuel utilisateur

Manuels Projecteur populaires d'autres marques