Digikeijs DR5052 DIGITURN Manuel utilisateur

DR5052 DIGITURN

P 1

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06 DR5052

DIGITURN

instrucon manual

rights reserved. No informaon, images or any part of

this document may be copied without the prior wrien

permission of Digikeijs.

Firmware 1.2.0

(2021-07-06)

DR5052 DIGITURN

P 2

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

1 Index

1.0 General information 2

1.1 Index 2

1.2 Guarantee and warranty provisions 3

1.3 Legal information 3

2.0 Product overview 4

2.1 General product information 4

2.2 Technical Specifications 5

2.3.0 Hardware overview DR5052 6

2.3.1 Hardware Overview DR5052-M7

2.3.2 Hardware Overview DR5052-R7

2.3.3 Hardware Overview DR4188-DC 8

3.0 Configuration Software 9

3.1 Introduction 10

3.2 Download software 11

3.3 Installing the configuration software 12

3.4 Connecting the DR5052 to the PC14 via USB 14

4.0 Programming 15

4.1 Overview Configuration Software 16

4.2 USB Features 17

4.3 Restoring the factory settings 18

4.4 Updating the Soft- and Firmware 19

4.5 Firmware Versions 20

4.6 LocoNet® Features 21

4.6.0 Module Properties Part 1 22

4.6.1 Module Properties Part 2 23

4.7 Scripting with DR. script 24

4.8 Configuring the turntable 25

4.8.1 Settings that can be used with all decoder types

(Basic, Plus and Profi) are available. 25

4.8.2 Settings for speed etc. for the Professional Decoder 26

4.8.3 Settings Profi decoder of the bridge for

Lighting and signal control. 27

4.8.4 Settings to display the DR5052 in the tool

the DR5052 to synchronize with the real Turntable 28 Please note!

This manual currently contains only the basic informaon and will be extended step by step. Suggesons,

improvements, addions, comments or suggesons are always welcome.

support@digikeijs.com

1.0 General Informaon

4.9 Adding track sidings 29

4.10 Parameterise track connections Basic Version 30

4.11 Parameterise track connections Plus and Profi version 31

4.12 Properties Global Detector 32

4.13 S88N® IN Settings

(only for plus and professional version) 33

4.13.1 ext88N for controlling the turntable 34

5.0 Control turntable 35

5.1 Turntable with the tool Control

(Fleischmann® protocol) 36

5.1 Turntable with the tool Control

(Märklin® protocol) 37

6.0 Connection examples 38

6.1 DR5052 Basic for Fleischmann® H0,N and Roco® TT

2-wire track 39

6.2 DR5052 Basic for Märklin® H0, 3-wire Track 40

6.3 DR5052 Basic for Roco® H0, 2-wire track 41

6.4 DR5052 Basic-Plus for Fleischmann® H0,N and Roco® TT

2-wire track 42

6.5 DR5052 Basic-Plus for Märklin® H0, 3-wire track 43

6.6 DR5052 Basic-Plus for Roco® H0 2-wire track 44

6.7 DR5052 Basic for Arnold N Turntable 45

6.8 DR5052 Basic for Märklin Z-turntable 46

7.0 Appendix 47

7.1 Comparison of Märklin® protocol and

Functions in the DR5052 47

7.2 Comparison Fleischmann® protocol and

Functions in the DR5052 48

DR5052 DIGITURN

P 3

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

1.2 Warranty and warranty condions

All our products come with a 24-month manufacturer's warranty. Please read these operang instrucons carefully.

Damage to the product caused by non-compliance with these instrucons will invalidate the warranty.

ATTENTION: The warranty is void if the housing of the product is opened.

1.3 Legal informaon

Prinng errors and mistakes, technical or other changes as well as changes in the availability of individual products are expressly reserved.

Data and illustraons are non-binding. All changes to hardware, rmware and soware are reserved.

We reserve the right to change the design of the product, the soware and / or the rmware without prior noce.

All Digikeijs operang instrucons and other wrien instrucons supplied and/or downloadable are protected by copyright.

Reproducon is not permied without the wrien permission of Digikeijs.

DR5052 DIGITURN

P 4

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

2.0 Product overview

2.1 General product informaon

The DR5052 is a turntable decoder that can control almost all turntables. All common control protocols are supported. When using the DR5052 in the Basic or Basic Plus ver-

sion, no modicaons to the turntable are necessary, the turntable can be connected and operated "Out of the Box". For the turntables of Roco® and Märklin® corresponding

adapters are available, so that also here a conversion of the turntable is omied, when using the Basic or Basic Plus version. For the professional version we oer a complete

conversion kit including an adapter board for a Plux22 decoder (The decoder must be purchased separately.). The polarity of the bridge track is reversed directly in the

DR5052, so no addional hardware is required. Of course, a RailCom® detector and a "normal" occupancy signal for the bridge track are also integrated.

Features of the individual versions:

DR5052 Basic The posion is detected by the latch of the turntable plaorm, so there is a "click" to be heard at every exit. Slow braking at the selected siding is

possible. The motor control is carried out directly via the DR5052. The speed can be set individually in the tool.

DR5052 Basic-Plus Posion detecon is carried out via addional feedback sensors on the track connecons. The un-latching of the turntable plaorm is performed once

and remains unlocked unl the DR5052 detects the selected siding. Now the DR5052 brakes down and drives slowly into posion. Aer reaching the

posion, the turntable plaorm latches safely again. The motor is controlled directly via the DR5052. The speed can be set individually in the tool.

DR5052 Professional Posion detecon is carried out via addional feedback sensors on the track connecons. The motor control is carried out via a separate

Locomove decoder (PluX22). Depending on the decoder used, load control is also available. Of course you can also use sound (at decoder) can be

played back. The light of the bridge house and the entrance and exit signals can also be controlled if the locomove decoder used provides sucient

funcon outputs. The maximum speed (CV5), the acceleraon ramp (CV3) and the deceleraon ramp (CV4) are programmed directly in the tool of the

DR5052.

Basic requirements for the use of the DR5052:

The turntable must be mechanically in order and funcon absolutely problem-free!

It is important that the latch-magnet coil (Fleischmann® or similar) of the turntable drive opens completely. There must be no clicking noises when turning when the locking

device is pulled out!

The DR5052 is directly supplied with track voltage and can also be operated via a separate DC power supply. The separate power supply must always be used when the track

voltage is below 16V. A voltage below 16V is not sucient to safely control the turntable!

! Aenon!

In principle, the track connecons of the turntable must be insulated from the shed tracks on both sides! This must be observed in order to avoid a short circuit. The connu-

ing tracks can then be normally supplied with track voltage again or monitored with a feedback signal. The polarity of the sidings can be set in the conguraon program.

DR5052 DIGITURN

P 5

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

2.2 Technical Specicaons

The terminals are designed for a cross-secon of 0.25mm² (Turntable and Sense) and 0.5mm² (Track Input). For the 0.25mm² terminals, a screwdriver should be used with a

blade size of 0.3×1.8mm (e.g. Wera® 118004) Other sizes can damage the terminals.

Supply voltage Track voltage

Oponal by an addional separate power supply DC min. 16V/2A max. 19V/2A.

(A separate power supply unit must be used for track voltages below 16V!) Digikeij's power supply DR60710-M recommended.

Maximum load bridge track 2A

Maximum load bridge motor 1A

RailCom RailCom® detector for the turntable plaorm.

feedback unit Feedback for occupancy indicaon of the turntable plaorm.

Bridge rotates / posion reached / Emergency stop acve.

Supported turntables Fleischmann® H0 and N all* (operaon as Basic, Basic-Plus, Pro version possible).

Märklin® H0 all* with adapter board DR5052-M (operaon as Basic. BasicPlus and Professional version not possible at the moment)

Märklin® Z (operaon only as basic version possible). A separate power supply DR60710-M is required! (Firmware Ver. 1.2.x)

Roco® H0 with adapter board DR5052-R (operaon as Basic. Basic-Plus and Professional version not possible at the moment!).

Roco® TT The connecon is the same as for the Fleischmann® H0 and N (operaon as Basic, Basic-Plus, Pro version possible).

Arnold® N only as basic version possible, an addional bridge recer is required. (Firmware Ver. 1.2.x)

stepper motor with adapter board DR5052-Step, max. phase current 1A (Firmware Ver. 1.2.x)

Available Product Sets** DR5052-BASIC Set contents: DR5052, USB cable, LocoNet cable 3m

DR5052-EXT Set contents: DR4088-OPTO, DR4188-DC adapter for posion feedback, 1m STP cable

(Required for the Basic-Plus and Pro versions. Note the number of rail sidings! )

DR5052-R Set contents: DR5052-ROCO adapter, 25 cm STP cable

(Required for operang a Roco® H0 turntable)

DR5052-M Set contents: DR5052-MARKLIN adapter, 25 cm STP cable

(Required for the operaon of a Märklin® H0 turntable)

DR5052-PRO Set contents: DR5052-PRO Adapter, DR5052-PLuX

*) The very old sheet metal discs cannot be controlled for the me being

**) Depending on the desired design, the corresponding installaon sets must be put together.

Fleischmann® H0 turntable with 16 track connecons should be operated as Basic-Plus variant:

1x DR5052-BASIC , 2x DR5052-EXT

Roco® H0 turntable with 16 track connecons is to be operated as Basic-Plus version:

Aenon! The DR5052 can only be operated as Basic Version and without LocoNet® on a digital system that operates according to the "Common Ground"

principle (for example Uhlenbrock®). Failure to do so may result in damage to the DR5052 and/or the control unit.

DR5052 DIGITURN

P 6

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

2.3.0 Hardware Overview DR5052

1S88N IN Connecon S88 Feedback modules

2L R Measuring voltage connecon Track connecons (see connec-

on examples)

3Turntable connecon Motor control

Y = yellow cable (colour code Fleischmann turntable)

G = grey cable (colour code Fleischmann turntable)

R = red cable (colour code Fleischmann turntable)

4Connecon turntable plaorm (bridge track)

Y = yellow cable (colour code Fleischmann turntable)

5LocoNet® connecon 1

6LocoNet® connecon 2

7red LED (three ashing cycles when turning le)

fast ashing cycle rotate fast speed

middle ashing cycle turn slow speed

stop slow ashing cycle (move pos. slowly)

8push buon Step Le

Turn the turntable one rail siding to the le

9push buon Rotate

Rotate turntable plaorm by 180 degrees

10 push buon Step Right

Turn the turntable one rail siding to the le

11 red LED (three ashing cycles when turning right)

fast ashing cycle rotate fast speed

middle ashing cycle turn slow speed

stop slow ashing cycle (move pos. slowly)

12 green LED

lights up Turntable bridge stands sll

turns out of turntable plaorm

lightning short Track siding was actuated

13 Track Input K and J

123456

14 USB Status LED

green RX

red TX

15 USB 2.0 connecon

16 External power supply

DC 16-19V 2A min.

17 green LED status (two ashing cycles)

Slow ashing rate Supply voltage present

fast ashing cycle no track voltage or no external

power supply available

79810 1211 15

13 14

DR5052 DIGITURN

P 7

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

2.3.1 Hardware Overview DR5052-M

This adapter is required to connect a Märklin® turntable to the DR5052 in the Basic, Basic-Plus and Pro

versions. (Please note the connecon example in points 6.2 and 6.5.) Corresponding installaon sets are

available in the online shop.

2.3.2 Hardware Overview DR5052-R

This adapter is used to connect a Roco® H0 turntable to the DR5052 in Basic, Basic-Plus and

Professional version required. (Please note the connecon example in points 6.3 and 6.6.) Correspon-

ding installaon sets are available in the online shop.

1Male connector for connecon to DR5052

(The pin header has 9 poles, i.e. 2 poles more than the DR5052, which is producon-

related and has no inuence on the funcon.)

2L R Connecon Measuring voltage Track sidings (see connecon examples)

3S88N® OUT connecon

Connecon to feedback module, bridge track occupied signal "ground detecon" (see

connecon examples)

4Male connector for connecng the turntable

5Jumper for determining whether 2-wire or 3-wire turntable.

1Male connector for connecon to DR5052

(The pin header has 9 poles, i.e. 2 poles more than the DR5052, which is producon-

related and has no inuence on the funcon.)

2L R Connecon Measuring voltage Track sidings (see connecon examples)

3S88N® OUT connecon

Connecon to the feedback modules, posion feedback (see connecon examples)

4Boards Connector for connecng the turntable

5Jumper Posion message internal or external.

(see Roco® operang instrucons)

DR5052 DIGITURN

P 8

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

2.3.3 Hardware Overview DR4188-DC

This adapter is required for the Basic-Plus and Pro versions. With this adapter an exact posion monito-

ring of the sidings in connecon with a DR4088OPTO is possible. (Please note the connecon example in

points 6.4, 6.5 and 6.6.) Corresponding installaon sets are available in the online shop.

1Male connector for connecon to DR4088-OPTO

2Terminal block for the connecon of the feedback units

Please note the connecon example in points 6.4, 6.5 and 6.6.

2.3.4 Hardware Overview DR5052-Step

This adapter is required to connect a stepper motor to the DR5052 for all versions.

1Male connector for connecon to DR5052

(The pin header has 9 poles, i.e. 2 poles more than the DR5052, which is producon-

related and has no inuence on the funcon.)

2Terminal block for connecng the stepper motor

Please note the following connecon example

3Bridge-track Connecon

DR5052 DIGITURN

P 9

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

3.0 CONFIGURATION

SOFTWARE

ATTENTION!!!! It may happen that the USB connecon to the PC is lost if the DR5052 remains permanently

connected via USB and the track input of the DR5052 is supplied with power. For this reason we recommend the use

of a USB isolator.

DR5052 DIGITURN

P 10

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

3.1 introductory remarks

A USB connecon to the PC is required to congure the DR5052.

Please use the supplied USB cable (a so-called USB A to USB mini cable).

System requirements:

• Intel Penum or AMD Athlon 64 processor

• Microso Windows 7 with Service Pack 1, Windows 8.1, or Windows 10

• 1 GB RAM for 32 Bit; 2 GB RAM for 64 Bit

• 100 MB free hard disk space

• Monitor with a resoluon of 1,024 x 768 (1280 x 800 recommended)

3.2 Download Soware

Do not connect the DR5052 to the PC unl the soware has been installed.