Digikeijs DR5013 DIGIREVERSE Manuel utilisateur

DR5013 DIGIREVERSE

P 1

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06 DR5013

DIGIREVERSE

Instrucon manual

(2021-07-06)

rights reserved. No informaon, images or any part of

this document may be copied without the prior wrien

permission of Digikeijs.

DR5013 DIGIREVERSE

P 2

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

1 Index

1.0 General informaon 2

1.1 Index 2

1.2 Warranty and warranty condions 3

1.3 Legal informaon 3

2.0 Product overview 4

2.1 General product informaon 4

2.2 Technical Specicaons 4

2.3 Hardware Overview 5

3.0 Conguraon soware 6

3.1 Introducon 7

3.2 Download soware 7

3.3 Installing the conguraon soware 8

3.4 Connecng the DR5013 to the PC via USB 11

4.0 Programming 12

4.1 Overview Conguraon Soware 13

4.2 USB Features 14

4.3 Restoring the factory sengs 15

4.4 Updang the So- and Firmware 16

4.5 Firmware Versions 17

4.6 LocoNet® Features 18

4.7.0 Module Properes Part 1 19

4.7.1 Module Properes Part 2 20

4.8 Scripng with DR. Script 21

4.9 Properes of sensor tracks 22

4.10 Global Detector Features 23

5.0 Connecon examples 24

5.1 DR5013 Connecon for short-circuit detecon 25

5.2 DR5013 Connecon for short-circuit detecon with

LocoNet® 26

5.3 DR5013 Connecon with sensor track (S0,S1,S2,S3)

and LocoNet® 27

Please note this manual!

This manual currently contains only the basic information and will be extended

step by step. Suggestions, improvements, additions, comments or suggestions

are always welcome.

suppor[email protected]

1 General Informaon

5.4 DR5013 Connecon with sensor tracks (S1,S2) with

LocoNet 28

5.5 DR5013 Connecon with sensor tracks (S1,S2) without

LocoNet® 29

5.6 External feedback connecon 30

DR5013 DIGIREVERSE

P 3

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

1.2 Warranty and warranty condions

All our products come with a 24-month manufacturer's warranty. Please read these operang instrucons carefully.

Damage to the product caused by non-compliance with these instrucons will invalidate the warranty.

ATTENTION: The warranty is void if the housing of the product is opened.

1.3 Legal informaon

Prinng errors and mistakes, technical or other changes as well as changes in the availability of individual products are expressly reserved.

Data and illustraons are non-binding. All changes to hardware, rmware and soware are reserved.

We reserve the right to change the design of the product, the soware and / or the rmware without prior noce.

All Digikeijs operang instrucons and other wrien instrucons supplied and/or downloadable are protected by copyright.

Reproducon is not permied without the wrien permission of Digikeijs.

DR5013 DIGIREVERSE

P 4

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

2.0 Product overview

2.1 General product informaon

The DR5013 operates either with sensor tracks (short-circuit-free) or via "short-circuit detecon" to switch over the reversing loop. The polarity of the reversing

loop can also be changed via a switch command. The busy signal of the secons (T, S1, S2) can be done via LocoNet® or external output (for GND or CS feed-

back). A short-circuit message can be output via LocoNet or via the SHORT output of the module. An integrated Railcom® detector for address evaluaon and

POM reading is also included. An electronic high-speed MOSFET relay with 3 ampere load capacity for switching over ensures absolutely trouble-free and wear-

free reversing of polarity of the reversing loop. There is also a USB port for conguraon and rmware updates.

2.2 Technical specicaons

The terminals are designed for a cross-secon of 0.5mm².

Outputs Loading capacity of

the reversing loop

Inputs

DR5013 External Short-circuit Message

External feedback Reverse loop

(CS current sensor)

External feedback Reverse loop

(GND Ground switching)

3A Sensor track 1

Sensor track 2

Feedback unit Reverse loop occupied

Railcom® Detector reversing loop

DR5013 DIGIREVERSE

P 5

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

2.3 Hardware Overview

1Sensor track 2

2Sensor track 1

3Track C (Railcom® Detector and Feedback Reverse Loop)

4Track T (Railcom® Detector and Feedback Reverse Loop)

5 Short Feedback

6Short Feedback external

Short circuit detected

7 FB-CS Track "Ground" brown

8FB-CS Feedback external (current sensor)

Connecon of feedback 1-16 to DR4088CS

loop track

9FB-GND Feedback external (switches to GND)

loop track

10 FB GND Connecon "C" on DR4088GND

11 LocoNet® connecon 1

12 LocoNet® connecon 2

13 Track Input K

14 Track Input J

15 USB Status LED

green RX

red TX

16 USB 2.0 connecon

345678

12 13 14

910

15 16 17 18

17 Status LED

blue Phase posion reversing loop rotated

red Short circuit

green Operang voltage available

18 Reversing switch

(When the buon is pressed, the DR5013

changes the polarity of the reversing loop.)

DR5013 DIGIREVERSE

P 6

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

3.0 CONFIGURATION

SOFTWARE

ATTENTION!!!! NEVER connect the DR5013 to the PC via USB when the TRACK INPUT of the DR5013 is connected

to the TrackOut (main track or programming track) of the central unit!

This can destroy the DR5013, the central unit and/or the USB interface in the PC.

The USB connecon to the PC must only be used to congure the DR5013!

DR5013 DIGIREVERSE

P 7

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

3.1 introductory remarks

A USB connecon to the PC is required to congure the DR5013.

To do this, you will need the supplied USB cable (a so-called USB A to USB mini cable).

System requirements:

• Intel Penum or AMD Athlon 64 processor

• Microso Windows 7 with Service Pack 1, Windows 8.1, or Windows 10

• 1 GB RAM for 32 Bit; 2 GB RAM for 64 Bit

• 100 MB free hard disk space

• Monitor with a resoluon of 1,024 x 768 (1280 x 800 recommended)

3.2 Download Soware

Do not connect the DR5013 to the PC unl the soware has been installed.

The soware can be downloaded from the DIGIKEIJS website.

DR5013 DIGIREVERSE

P 8

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

Important !!!

Do not connect the DR5013 to the PC unl the soware and driver ha-

ve been successfully installed.

3.3 Install soware

Aer you have successfully downloaded the soware, the installaon can be started by double-clicking on the DR5013xx.exe le.

Make sure that you have administrator rights on your PC.

DR5013 DIGIREVERSE

P 9

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

The following screen appears aer a few seconds. Click "Next".

If you want to change the locaon of the soware, you can do so on the next screen.

However, it is recommended to leave the sengs as they are and click "Next".

DR5013 DIGIREVERSE

P 10

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

Now follows a short overview of the sengs. Click on "Install" if you agree.