Digi One SP Manuel utilisateur

February 5, 2004

Using the Digi One SP to Network Doppler Systems

DDF6001s using an Ethernet

A Technical Application Note from Doppler Systems Inc.

Introduction

The Digi One SP allows a device with a serial port to be connected to an Ethernet. This

application note describes the connections and setup required to use the Digi One SP with

the Doppler DDF6001 direction finders. (Note that this application note also applies to

older DDF6001 direction finders).

Network Configuration

The figure below shows the configuration of the network when using the Digi One SP.

Each Digi One device is a terminal server that allows one connection. Therefore, only

one computer connected to the network can control and monitor the direction finder sites.

If it necessary to have multiple computers monitor the DF network, then BearingTrack

Server (see BearingTrack manual) must be used instead of the Digi One SP.

Ethernet

Computer

DF RX

Digi One

SP

Digi One

SP

DF RX

DF RX

Digi One

SP

Programming the Digi One SP

The Digi One SP comes with a CD that contains the software necessary to set it up. First

connect the Digi One SP to its power supply and then connect it to the network using a

standard category 5 networking cable. Insert the CD and wait for the set up program to

launch. The Digi Device Setup wizard should also automatically start. Press Next on the

first page of the wizard. The wizard will locate the Digi One device. Select the device

and press Next. Set the IP address and subnet mask of the device consistent with your

network. Each Digi One SP device must have a unique IP address in order to work with

the BearingTrack software. Set the IP address and make a note of the address you set.

Press the next button and select Incoming Connection. Press the Next button and select

Incoming Network Connection. Press Next and select TCP Sockets. Press Next and

set the serial port parameters to Baud Rate 2400, Data bits 8, Parity None, Stop Bits 1,

and Flow Control None. Press Next and verify the settings you’ve entered and then press

Next again and wait for the Digi One SP to reboot (takes about 1 minute).

If you want to modify any of the settings, the Digi One comes with a built in web server

so you can use a web browser (e.g. Internet Explorer) to modify the settings. Refer to the

Digi One SP manual for instructions on how to use a web browser to modify its settings.

Configuring the DDF6001

During the normal setup of the DDF6001 WinRDFCommand is used to set the CIV

address of the DF and to change other settings if needed. To use WinRDF Command

first connect J1 on the DDF6001 to the computer using a serial RS232 cable. Launch the

WinRDFCommand program. Set up the DDF6001 as you desire and then press the Auto

Output On radio button to switch the DF into the automatic output mode. Automatic

output must be enabled to use the DF6001 with the Digi One SP.

Configuring Bearing Track

When setting up the sites in Bearing Track (see manual or help file) select the Enable

Internet Connection checkbox for each site and enter the IP address of the Digi One SP

device at that site location. Enter 2101 for the port number.

Installing the Digi One SP

Connect the serial connector on the Digi One SP to J1 of the DF600. Connect a category

5 cable from the Digi One SP to your network connection. Connect the power supply

included with the Digi One SP to the unit.

Operation

Use BearingTrack as described in the BearingTrack manual or help files.

Autres manuels pour One SP

6

Table des matières

Autres manuels Digi Serveur

Digi

Digi ConnectPort LTS 8 Manuel utilisateur

Digi

Digi One TS W Manuel utilisateur

Digi

Digi Connect EZ Mini Manuel utilisateur

Digi

Digi Connect IT 16 Manuel utilisateur

Digi

Digi PortServer/8 Manuel utilisateur

Digi

Digi Connect IT 16 Manuel utilisateur

Digi

Digi Passport 48 Manuel utilisateur

Digi

Digi Connect IT 4 Manuel utilisateur

Digi

Digi PortServer TS Series Manuel utilisateur

Digi

Digi PortServer TS 1 M MEI Manuel utilisateur

Digi

Digi PortServer TS M MEI Manuel utilisateur

Digi

Digi TS 4 MEI Manuel utilisateur

Digi

Digi One IAP Haz Manuel utilisateur

Digi

Digi Connect Wi-SP Manuel utilisateur

Digi

Digi DIGI CONNECT ES Manuel utilisateur

Digi

Digi PortServer TS 8 Mode d’emploi

Digi

Digi ConnectPort TS 8 MEI Manuel utilisateur

Digi

Digi Connectware Digi CM 16 Manuel utilisateur

Digi

Digi 1002 Manuel

Digi

Digi Connectware PortServer TS 1 + Modem Manuel utilisateur

Digi

Digi ConnectPort LTS 8 Manuel d'installation

Digi

Digi LTS 32 Manuel utilisateur

Digi

Digi DC-ES-4SB Manuel utilisateur

Digi

Digi DIGI CONNECT ES Manuel d'exploitation

Manuels Serveur populaires d'autres marques

HP

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur