Dickey-John INTELLIAG ISO6 Manuel utilisateur

INTELLIAG®

ISO6

™

PLANTER DRILL CONTROL

VERSION 4 QUICK START GUIDE

Quick Start Guide

Add ISO6 WSMT Module

here (from spec sheet 2nd page)

SINCE 1966

OPERATOR’S MANUAL

ISO6Version 4 Quick Start Guide / I

6011662 Rev B

Safety Notices.....................................................................................................3

Disclaimer..................................................................................................................................3

Basic Setup.........................................................................................................4

User Level 2 (Dealer) ................................................................................................................4

Basic Setup Steps .....................................................................................................................5

Modules...............................................................................................................7

Harness Select....................................................................................................8

Identify Harness Style................................................................................................................8

Selecting a Harness:...........................................................................................................8

Row Setup...........................................................................................................9

To Access Row Setup: ..............................................................................................................9

Controls.............................................................................................................10

Assign a Control Channel........................................................................................................10

To Create a Control Channel:...........................................................................................10

Enter Channel Parameters......................................................................................................11

Valve Calibration .....................................................................................................................12

Perform a Valve Calibration (Figure 9) .............................................................................13

Limit Output (Granular)............................................................................................................14

To Perform a Limit Output:................................................................................................14

Granular Spreader Calibration.................................................................................................15

Perform a Spreader Calibration ........................................................................................15

Spreader Constants Defined...................................................................................................17

Density ..............................................................................................................................17

Spreader Constant............................................................................................................17

Target Meter RPM.............................................................................................................18

Number (#) Meter Revs ....................................................................................................18

Pulse Count.......................................................................................................................18

New Spreader Constant....................................................................................................18

Amount Dispensed............................................................................................................18

Shaft Turn .........................................................................................................................18

Liquid Flow Calibration............................................................................................................18

Perform a Valve Calibration..............................................................................................18

Limit Output.......................................................................................................................19

K-Factor Calibration.................................................................................................................20

Method 1: 100% Catch Test .............................................................................................20

Perform a Liquid Flow Catch Test...........................................................................................21

Operations.........................................................................................................22

To Edit an Operation: ..............................................................................................................22

Configurations..........................................................................................................................23

To Activate/Change a Configuration:................................................................................23

To Edit a Configuration: ....................................................................................................24

To Change the Operation Product Class:.........................................................................25

To Change an Assigned Material:.....................................................................................25

To Change the Row Pattern: ............................................................................................25

Materials............................................................................................................26

To Create a Material:...............................................................................................................26

Setup Parameters For Planter Control....................................................................................27

Setup Parameters For Liquid Control......................................................................................28

Setup Parameters For Granular Control .................................................................................29

OPERATOR’S MANUAL

II / ISO6Version 4 Quick Start Guide

6011662 Rev B

Clutch Sections ................................................................................................30

Identify Sections and Outputs..................................................................................................30

Multiple Output Module Assignment.................................................................................30

To Enter # of Outputs per Module:....................................................................................30

Assign Channels/Rows/ Outputs/Switches....................................................31

To Assign Clutch Sections:......................................................................................................31

Geometry...........................................................................................................32

To Enter X/Y Coordinates:.......................................................................................................32

X and Y Coordinate Example..................................................................................................33

Row Sensors.....................................................................................................35

To Assign Sensors: .................................................................................................................35

Accessories ......................................................................................................39

Accessory Summary................................................................................................................39

Accessory Setup......................................................................................................................39

Accessory Alarm Setup...........................................................................................................41

Sensor Name....................................................................................................................41

High/Low Alarm Level.......................................................................................................41

High/Low Alarm Delay.......................................................................................................41

High/Low Alarm Gating.....................................................................................................41

High/Low Alarm Behavior .................................................................................................42

Pressure Sensor Setup ...........................................................................................................42

Hopper Sensor Setup..............................................................................................................43

RPM Sensor Setup..................................................................................................................44

Digital Sensor Setup................................................................................................................45

Task Controller.................................................................................................47

Task Controller Compatibility...................................................................................................47

To Disconnect Task Controller:.........................................................................................47

To Reconnect to the Task Controller:...............................................................................47

To Refine an Operation:....................................................................................................48

Ground Speed...................................................................................................49

To Select a Ground Speed Type:............................................................................................49

User Levels .......................................................................................................50

Lock To User Level 1 (Operator).............................................................................................50

To Set User Level 1 Mode: ...............................................................................................50

User Level 2 (Dealer) ..............................................................................................................50

To Unlock a Controller into User Level 2 (Dealer):...........................................................50

Frame Fold/Working Hydraulics......................................................................51

Fame Fold/Working Hydraulics ...............................................................................................51

Setting Up Frame Fold Controls: ......................................................................................51

Setting Up Working Hydraulics Functions:..............................................................................54

Adding Work Functions to the Work Screen: ..........................................................................55

Virtual Section Switches..................................................................................56

Setting Up Virtual Section Switches:.......................................................................................56

OPERATOR’S MANUAL

ISO6Version 4 Quick Start Guide SAFETY NOTICES / 3

6011662 Rev B

SAFETY NOTICES

Safety notices are one of the primary ways to call attention to

potential hazards.

This Safety Alert Symbol identifies important safety messages

in this manual. When you see this symbol, carefully read the

message that follows. Be alert to the possibility of personal

injury or death.

WARNING

Use of the word WARNING indicates a potentially hazardous

situation which, if not avoided, could result in death or

serious injury.

CAUTION

Use of the word CAUTION with the Safety Alert Symbol

indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

CAUTION

Use of the word CAUTION without the Safety Alert Symbol

indicates a potentially hazardous situation which, if not

avoided, may result in equipment damage.

DANGER

Use of the word DANGER indicates a potentially hazardous

situation which, if not avoided, could result in death or

serious injury.

DISCLAIMER

DICKEY-john reserves the right to make engineering refinements

or procedural changes that may not be reflected in this manual.

Material included in this manual is for informational purposes and

is subject to change without notice.

DANGER

OPERATOR’S MANUAL

4 / BASIC SETUP ISO6Version 4 Quick Start Guide

6011662 Rev B

BASIC SETUP

The ISO6Quick Start Guide provides the basic steps for user

level 2 and 3 administrators to setup a system.

The IntelliAg system is accessed by pressing the ISO6button in

the UT object pool selection box (location will vary with UT mfg).

Figure 1

Accessing IntelliAg IS06 Screens

USER LEVEL 2 (DEALER)

User Level 2 provides open access to all setup/configuration

screens excluding Factory Reset and the Alarm Log (User Level

3 access). To change from operator level to dealer level, a 6-digit

password is required. Password includes the five-digit serial

number found on the label of the ISO6module or on the

Version screen.

OPERATOR’S MANUAL

ISO6Version 4 Quick Start Guide BASIC SETUP / 5

6011662 Rev B

To Unlock to Dealer Access:

1. At the Version screen,

-Record the serial number of the ISO6module.

-Press the PASSWORD button.

2. On the Password screen, enter the 6-digit password as

follows:

-Enter the first digit as 2.

-For the next five digits, enter the last five digits of the

serial number taken from the ISO6module found on the

label or

-The last five digits found at the Version Information

screen (example: S/N 163210044 - use 10044).

3. Press the check button to accept password. At the Password

screen, text at screen bottom states “Dealer screens on” in

the User Level 2 (Full Access) mode.

Figure 2

Enter Password for User Level 3 Access

BASIC SETUP STEPS

The basic steps below are recommended in the listed order for

initial system setup:

1. Module Configuration (set module addresses)

2. System screen (select harness)

3. Rows (assign) Controls (define control channels)

4. Operations (define control/application configuration)

5. Materials (specify material type)

6. Row Clutch Setup (if applicable)

7. Liquid Section Setup (if applicable)

8. Geometry (implement layout)

OPERATOR’S MANUAL

6 / BASIC SETUP ISO6Version 4 Quick Start Guide

6011662 Rev B

9. Sensors (assign sensor type)

10. Accessory sensors

11. Work Screen layout setup

NOTE

Recommended Setup order is using the System Setup buttons

from left to right.

Figure 3

Home Menu Screen

OPERATOR’S MANUAL

ISO6Version 4 Quick Start Guide BASIC SETUP / 7

6011662 Rev B

MODULES

The Modules screen displays what modules are currently

detected on the CAN bus. When a new module is added to the

system, the module appears as the last module and must be

placed in its correct position as installed on the implement.

To Add a New Module:

1. Press the Module Address input box of the new module.

2. Manually enter the correct module address location.

-The module location automatically adjusts to the correct

position and proceeding modules change to the new

module address.

Figure 4

Modules Screen

OPERATOR’S MANUAL

8 / HARNESS SELECT ISO6Version 4 Quick Start Guide

6011662 Rev B

HARNESS SELECT

IDENTIFY HARNESS STYLE

IM PORTANT

A harness style must be selected prior to channel setup.

The system default is set to “Monitor Only” with no control

channels enabled.

IM PORTANT

Harness selection changes the system configuration and

should only be done when changing physical harnesses.

It is recommended to perform a complete system setup after

changing the harness type.

SELECTING A HARNESS:

1. Press the SYSTEM button.

2. Press the Harness drop down box and select the

appropriate harness.

3. Press the SAVE button.

-Press the Cancel ‘X’ button to cancel the

selected changes.

4. A power cycle is required to reboot the system.

Figure 5

Select the Harness Type

OPERATOR’S MANUAL

ISO6Version 4 Quick Start Guide ROW SETUP / 9

6011662 Rev B

ROW SETUP

Row Setup will allow the user to define the number of rows on

the implement and also set the row spacing. Total implement

width is calculated from these parameters.

TO ACCESS ROW SETUP:

1. Press the ROWS button to access the Row Setup screen.

2. Enter parameters on the setup screen shown in Figure 6.

NOTE

Applies to planter, granular, liquid, RPM, and Monitor

Only applications.

Figure 6

Row Setup

Table des matières

Autres manuels Dickey-John Unité de contrôle

Dickey-John

Dickey-John Land Manager SE Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur