Dialogic BorderNet 2020 Mode d’emploi

Dialogic®BorderNet™ 2020 Integrated Multimedia

Gateway Quick Start Installation Guide

This document provides a high-level overview of how to connect power and network cabling

for the BorderNet 2020 IMG. For detailed information about installation and setup, refer to

the online documentation at http://www.dialogic.com/manuals/bordernet2020img1.0/default.htm.

Before you begin, review the packing list to verify that you received all items listed. If there

are any discrepancies, contact your Dialogic representative.

Locating the Base MAC Address

The base MAC address is printed on the identification label located on the underside rear of

the 2020 IMG. The base MAC address is assigned to the CTRL ports. The other MAC

addresses are under software control.

Use this base MAC address when configuring the IP address. Because of its location, we

recommend that you obtain the base MAC address before you install the system. The

identification label is similar to this example:

Connecting AC power

AC power modules must be plugged into three-prong grounded outlets. Do not use the

external grounding points on the rear of an AC 2020 IMG to ground the system. These

grounding points are for DC system grounding only.

AC input power:

100 - 240 V AC, 60 - 50 Hz, 2 A - 1 A

115 V AC @ 2 A, or 230 V AC @ 1 A

Redundant, hot-swappable AC power modules are located at the rear of the docking station.

Note: When connecting a second power supply, you do not need to turn off power to the

primary AC power module.

Connecting DC power

You must connect the DC 2020 IMG to earth ground before connecting power. To connect a

ground to the DC 2020 IMG, use 10, 12, or 14 AWG machine tool wire (MTW) (green/yellow

for earth ground). Dialogic supplies a two-hole #10 solderless crimp grounding lug that is

attached to the grounding screws on the rear of the 2020 IMG.

Caution: Do not daisy-chain two or more systems. Do not wire the 2020 IMG directly to

other equipment or to a common bus bar.

DC input power:

-40 to -60 V DC (-48 V DC nominal) @ 6 A

Redundant, hot-swappable DC power modules are located at the rear of the docking station.

Warning! You must connect the 2020 IMG to a true earth ground to maintain

signaling integrity and to prevent electrical shock. Do not connect ground to -48 V.

Dialogic® BorderNet™ 2020 Integrated Multimedia Gateway Quick Start Installation Guide

Connecting to a Single DC Power Source

To connect a single external DC power source to the 2020 IMG:

1. Turn OFF the existing external power source and disconnect it from the power

supply.

Warning! Failure to turn the power OFF at the source may result in electrical

shock.

2. Attach the wires from the external power source to the DC power module plug.

3. Insert the plug into the DC power module.

4. Reconnect the external power source and turn the power ON.

5. Press the ON button on the front of the server.

Connecting to a Redundant DC Power Source

To connect a redundant DC power source to the 2020 IMG, follow the Connecting to a Single

Power Source procedure.

Note: Do not turn off power to the primary -48 V DC module or the unit will shut down.

DC power cables

A 500 mm DC power pigtail cable is included with DC systems. If you require a longer cable,

the 4 m cable is available for order (P/N BDN-CBL-1000).

Caution: The color specifications for the DC power cables are not identical. Be sure to

review the specifications that are shipped with your cable before installation.

DC power cable (500 mm)

DC power pigtail 4 m cable (P/N BDN-CBL-1000)

Dialogic® BorderNet™ 2020 Integrated Multimedia Gateway Quick Start Installation Guide

Connecting to the Network

Complete the following steps to connect the 2020 IMG to the network:

1. Access the Dialogic®BorderNet™ 2020 Integrated Multimedia Gateway WebHelp at

http://www.dialogic.com/webhelp/BorderNet2020/1.0.0/WebHelp/default.htm.

2. Refer to the Installing the Software section in the Dialogic®BorderNet™ 2020

Integrated Multimedia Gateway WebHelp.

3. Review the options for installing the software and choose the appropriate installation

method for your site.

4. Install the software.

5. Follow the instructions for configuring the IP address and setting the system software

file name as described in the Dialogic®BorderNet™ 2020 Integrated Multimedia

Gateway WebHelp.

6. Using a shielded Ethernet cable, connect CTRL 0 or CTRL 1 to your network Ethernet

switch. Use the CTRL Ethernet connectors on the rear of the 2020 IMG for network

management.

Depending on the configuration, the binary downloads from either an SD card or from an

FTP server that you configured. Once the binary downloads, you can begin the configuration

as described in the Dialogic®BorderNet™ 2020 Integrated Multimedia Gateway WebHelp.

You will connect the remaining cables as you configure the system.

Document P/N: 64-1103-02

Autres manuels pour BorderNet 2020

Table des matières

Autres manuels Dialogic Porte

Dialogic

Dialogic 4000 Series Manuel utilisateur

Dialogic

Dialogic 1000 Series Manuel utilisateur

Dialogic

Dialogic IMG 1010 Manuel utilisateur

Dialogic

Dialogic 4000 Series Manuel utilisateur

Dialogic

Dialogic Mitel SX-2000 Guide de démarrage rapide

Dialogic

Dialogic DMG1004LSW Manuel utilisateur

Dialogic

Dialogic IMG 2020 Mode d’emploi

Dialogic

Dialogic 2000 Series Manuel utilisateur

Dialogic

Dialogic 2000 Series Manuel utilisateur

Dialogic

Dialogic 4000 Series SU4.1 Manuel utilisateur

Dialogic

Dialogic 1000Series Manuel utilisateur

Dialogic

Dialogic IMG 1004 Instructions de montage

Dialogic

Dialogic IMG 1004 Manuel utilisateur

Dialogic

Dialogic Vision CX Video Mode d’emploi

Dialogic

Dialogic IMG 1004 Manuel utilisateur

Dialogic

Dialogic IMG 1010 Manuel utilisateur

Dialogic

Dialogic IMG 1010 Manuel utilisateur

Dialogic

Dialogic 3000 Series Manuel utilisateur

Dialogic

Dialogic BorderNet 500 Manuel de l'opérateur

Dialogic

Dialogic IMG 1010 Manuel utilisateur

Dialogic

Dialogic Integrated Media Gateways IMG 1010 Guide de configuration

Dialogic

Dialogic IMG 1010 Manuel utilisateur

Dialogic

Dialogic BorderNet 2020 Instructions d'installation

Dialogic

Dialogic IMG 1010 Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur