DFI Q7-951 Manuel utilisateur

Q7-951

Qseven Carrier Board

User’s Manual

A14720205

This publication contains information that is protected by copyright. No part of it

may be reproduced in any form or by any means or used to make any transfor-

mation/adaptation without the prior written permission from the copyright hold-

ers.

This publication is provided for informational purposes only. The manufacturer

makes no representations or warranties with respect to the contents or use

of this manual and specifically disclaims any express or implied warranties of

merchantability or fitness for any particular purpose. The user will assume the

entire risk of the use or the results of the use of this document. Further, the

manufacturer reserves the right to revise this publication and make changes to

its contents at any time, without obligation to notify any person or entity of such

revisions or changes.

Trademarks

All trademarks and registered trademarks of products appearing in this manual

are the properties of their respective holders.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandthereceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhich

the receiver is connected.

• ConsultthedealeroranexperiencedradioTVtechnicianforhelp.

Notice:

1. The changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission

limits.

Table of Contents

Trademarks�� 2

FCC and DOC Statement on Class B�� 3

About this Manual �� 6

Warranty �� 6

Static Electricity Precautions �� 7

Safety Measures�� 7

About the Package �� 8

Before Using the System Board �� 8

Chapter 1 - Introduction �� 9

Specifications�� 9

Chapter 2 - Hardware Installation�� 11

System Board Layout �� 11

Jumper Settings�� 12

COM2 RS232/RS422/RS485 Select �� 12

USB Power Select�� 13

Panel Power Select �� 14

Super IO Select �� 15

Power-on Select �� 16

Backlight Control Level Select�� 17

AT Mode Select �� 18

Rear Panel I/O Ports�� 19

DC-in 12V �� 20

Serial (COM) Ports �� 21

VGA Port�� 22

RJ45 LAN Port �� 23

Universal Serial Bus Connectors�� 24

Audio�� 25

Internal I/O Connectors................................................................ 26

S/PDIF Connector..................................................................... 26

LVDS LCD Panel Connector and LCD/Inverter Power Connector...... 27

Digital I/O Connector and Digital I/O Power Connector ................. 29

Mini PCIe ................................................................................ 30

SATA (Serial ATA) Connectors .................................................... 31

Cooling Fan Connectors............................................................. 32

Chassis Intrusion Connector ...................................................... 33

Standby Power LED .................................................................. 34

WAN LED, LAN LED, PAN LED .................................................... 35

Front Panel Connectors ............................................................. 36

Battery ................................................................................... 37

MXM Connector........................................................................ 38

I2C Connector .......................................................................... 41

Can-bus Connector................................................................... 42

USB Client Connector ............................................................... 43

SM bus ................................................................................... 44

LPC Connector ......................................................................... 45

External Power......................................................................... 46

Introduction

About this Manual

An electronic file of this manual is included in the CD. To view the user’s manual

in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board

Utility CD) will appear. Click “User’s Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the

product, inability to use the product, unauthorized replacement or alteration

of components and product specifications.

2. The warranty is void if the product has been subjected to physical abuse,

improper installation, modification, accidents or unauthorized repair of the

product.

3. Unless otherwise instructed in this user’s manual, the user may not, under

any circumstances, attempt to perform service, adjustments or repairs on the

product, whether in or out of warranty. It must be returned to the purchase

point, factory or authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial

damages to the product that has been modified or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components

or devices even before installing them in your system unit. Static electrical dis-

charge can damage computer components without causing any signs of physical

damage. You must take extra care in handling them to ensure against electro-

static build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag

until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the compo-

nents, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold

modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and

other components. Perform the upgrade instruction procedures described

at an ESD workstation only. If such a station is not available, you can

provide some ESD protection by wearing an antistatic wrist strap and

attaching it to a metal part of the system chassis. If a wrist strap is

unavailable, establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Safety Measures

To avoid damage to the system:

• UsethecorrectACinputvoltagerange.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for instal-

lation or servicing. After installation or servicing, cover the system chassis

before plugging the power cord.

Battery:

• Dangerofexplosionifbatteryincorrectlyreplaced.

• Replace only with the same or equivalent type recommend by the manufac-

turer.

• Disposeofusedbatteriesaccordingtolocalordinance.

Introduction

About the Package

The system board package contains the following items. If any of these items are

missing or damaged, please contact your dealer or sales representative for as-

sistance.

One motherboard

One Serial ATA data cable

One power cable

One COM cable

One DVD

One QR (Quick Reference)

The system board and accessories in the package may not come similar to the

information listed above. This may differ in accordance to the sales region or

models in which it was sold. For more information about the standard package in

your region, please contact your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need at least the

following internal components.

• A CPU

• Memory module

• Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use which will nor-

mally include at least a keyboard, a mouse and a video display monitor.

Introduction

Chapter 1 - Introduction

Specifications

Graphics

Audio

Serial ATA

TPM

I/O Chip

Damage Free

Intelligence

Temperature

Humidity

Rear Panel I/O

Ports

• Chrontel CH7317B (SDVO to RGB DAC)

• Realtek ALC262 audio codec

• 2-channel audio output

• Two Serial ATA ports

• SATA speed up to 3Gb/s (SATA 2.0)

• Inneon SLB9635TT12

• Winbond 83627DHG-P controller

• LPC interface

• Supports system fan

• Default I/O port address “2Eh”

• Monitors system temperature and overheat alarm

• Monitors system fan speed and failure alarm

• 0oC to 60oC

• Operating: 10% to 90%

• 1 12V DC-in jack

• 1 DB-15 VGA port

• 1 DB-9 RS232 serial port

• 2 USB 2.0/1.1 ports

• 1 RJ45 LAN port

• 1 line-out jack

Introduction

I/O Connectors

Expansion Slots

Board to board

Connectors

PCB

• 2connectorsfor4externalUSB2.0/1.1ports

• 1connectorforanexternalRS232/422/485serialport

• 1LPCconnector

• 1I2C connector

• 1CAN-busconnector

• 1USBclientconnector

• 1LVDSLCDpanelconnector

 -18/24-bitsinglechannel

• 1LCD/inverterpowerconnector

• 18-bitDigitalI/Oconnector

• 1DigitalI/Opowerconnector

• 1audioconnectorforline-in,line-outandmic-injacks

• 1S/PDIFconnector

• 2SerialATAconnectors

• 14-pin12V/5Vpowerconnector

• 1chassisintrusionconnector

• 1frontpanelconnector

• 1fanconnector

• 1SD/SDIO/MMCsocket

• 1miniPCIesocket

• OneMXMconnector

• 3.5”formfactor

• 102mm(4.02”)x147mm(5.79”)

Table des matières

Autres manuels DFI Carte mère

DFI

DFI 586IHX Manuel utilisateur

DFI

DFI 915P-TAL Manuel utilisateur

DFI

DFI SD100-H110/Q170 Manuel utilisateur

DFI

DFI CS30-TC Manuel utilisateur

DFI

DFI LANPARTY DK X58-T3EH6 Manuel utilisateur

DFI

DFI G586IPBS Manuel utilisateur

DFI

DFI LanParty UT NF4 SLI EXPERT Venus Manuel utilisateur

DFI

DFI LanParty nF4 Manuel utilisateur

DFI

DFI RNO171 Manuel utilisateur

DFI

DFI AD76 RAID Manuel utilisateur

DFI

DFI SB300-C Manuel utilisateur

DFI

DFI 486-OCV Plus Manuel utilisateur

DFI

DFI CW35-TC Manuel utilisateur

DFI

DFI PB61-V3 Manuel utilisateur

DFI

DFI RNO171 Manuel utilisateur

DFI

DFI OT951-D Series Manuel utilisateur

DFI

DFI Blood-Iron G41-T33 Manuel utilisateur

DFI

DFI PT332-DRM Manuel utilisateur

DFI

DFI G7S620-N Manuel utilisateur

DFI

DFI G7V600-B Manuel utilisateur

DFI

DFI NFII ULTRA-AL Manuel utilisateur

DFI

DFI KD631-C236/Q170 Manuel utilisateur

DFI

DFI PR810-C622 Manuel utilisateur

DFI

DFI Infinity NF series Manuel utilisateur

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur