DFI CA61 Manuel utilisateur

CA61

Rev. B+

System Board

Users Manual

41730039

This publication contains information that is protected by copyright. No

part of it may be reproduced in any form or by any means or used to

make any transformation/adaptation without the prior written permission

from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any express

or implied warranties of merchantability or fitness for any particular purpose.

The user will assume the entire risk of the use or the results of the use of

this document.Further,the manufacturer reserves the right to revise this

publication and make changes to its contents at any time, without obligation

to notify any person or entity of such revisions or changes.

Trademarks

Microsoft®MS-DOS®, WindowsTM, Windows®95, Windows®98,

Windows®2000 and Windows NT®are registered trademarks of

Microsoft Corporation. Intel®,Pentium®IIIand CeleronTM are registered

trademarks of Intel Corporation.VIA Cyrix®IIIis a registered trademark

of VIA Technologies, Inc. Award is a registered trademark of Award

Software,Inc.Other trademarks and registered trademarks of products

appearing in this manual are the properties of their respective holders.

Caution:

Danger of explosion if battery incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Dispose of used batteries according to the battery manufacturers

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications ...................................................................

1.2 Package Checklist ........................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ...............................................................................

2.2 System Memory ..........................................................................................

2.3 Frequency Ratio Settings for Processors ....................................

2.4 Factory Testing Jumper ..............................................................................

2.5 Jumper Settings for Selecting the CPUs Front Side Bus......

2.6 Jumper Settings for Clearing CMOS Data ................................

2.7 Jumper Settings for Wake-On-Keyboard/Mouse.......................

2.8 Ports and Connectors ............................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System .......................................................

3.1.1 Standard CMOS Setup ..........................................................

3.1.2 BIOS Features Setup................................................................

3.1.3 Chipset Features Setup ..........................................................

3.1.4 Power Management Setup ...................................................

3.1.5 PNP/PCI Configuration ..........................................................

3.1.6 Load Fail-Safe Settings .............................................................

3.1.7 Load Optimal Settings ............................................................

3.1.8 Integrated Peripherals ..............................................................

3.1.9 Supervisor Password ...............................................................

3.1.10 User Password .............................................................................

3.1.11 IDE HDD Auto Detection ..................................................

3.1.12 Save & Exit Setup ......................................................................

3.1.13 Exit Without Saving ....................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface .........................................................

4.2 Hardware Doctor Utility ..........................................................................

4.3 VIA®Service Pack .......................................................................................

4.4 Drivers and Utilities Installation Notes ...........................................

Appendix A - System Error Messages

A.1 POST Beep.......................................................................................................................

A.2 Error Messages..............................................................................................................

Appendix B - Troubleshooting

B.1 Troubleshooting Checklist ......................................................................

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• VIA82C693A and 82C596B (PC-133)

Processor

The system board is equipped with Socket 370 for installing an Intel

CeleronTM FCPGA/PPGA, Pentium®III FCPGA or VIA Cyrix®III

processor. The system board is also equipped with a switching

voltage regulator that supports 1.30V to 2.05V core voltage for

various processors.

• Pentium®III FCPGA: 133MHz FSB (533EB-733EB) or 100MHz

FSB (500E-700E) processor

• CeleronTM 66MHz FSB: FCPGA (566MHz-600MHz) or PPGA

(300A-533MHz) processor

• VIA CyrixIII processor

System Memory

• 16MB to 640MB using VCM (Virtual Channel Memory) or PC

SDRAM DIMM (unbuffered or registered)

• Three 168-pin DIMM sockets

• Uses x64 or x72 PC SDRAM, 3.3V

- PC-66 SDRAM DIMM for 66MHz FSB processors

- PC-100 SDRAM DIMM for 100MHz FSB processors

- PC-133 SDRAM DIMM for 133MHz FSB processors

• ECC supported (uses x72 PC SDRAM DIMM)

Chapter 1 - Introduction

DIMMs

2MBx64/x72

4MBx64/x72

8MBx64/x72

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64/x72

32MBx64/x72

Memory Size

128MB

256MB

Introduction

Expansion Slots

The system board is equipped with 1 dedicated AGP slot, 3

dedicated PCI slots, 2 dedicated 16-bit ISA slot and 1 shared PCI/

ISA slot. All PCI and ISA slots are bus masters.

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to Chapter 4 for instructions on

using the DMI utility.

ATX double deck ports

 2 USB ports

 2 DB-9 serial ports

 1 DB-25 parallel port

 1 mini-DIN-6 PS/2 keyboard port

 1 mini-DIN-6 PS/2 mouse port

Connectors

 1 connector for IrDA interface

 2 IDE connectors

 1 floppy connector

 1 20-pin ATX power supply connector

 1 Wake-On-LAN connector

 1 SB-LINK connector

 2 fan connectors for CPU and chassis fans

Note:

If you are using more than one DIMM, make sure you insert

the same type of DIMMs into the DIMM sockets. Using

different types (VCM and PC SDRAM) of DIMMs may cause

problems.

Introduction

PCI Bus Master IDE Controller

 Two PCI IDE interfaces support up to four IDE devices

 Supports ATA/33 or ATA/66 hard drives

 PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up

to 16.6MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 ATAPI CD-ROM, LS-120 and ZIP supported

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. It

supports peripheral devices that meet the IrDA or ASKIR standard.

USB Ports

The system board is equipped with two USB ports. USB allows

data exchange between your computer and a wide range of

simultaneously accessible external Plug and Play peripherals.

BIOS

 Award BIOS, Windows95/98 Plug and Play compatible

 Supports SCSI sequential boot-up

 Flash EPROM for easy BIOS upgrades

 Includes Symbios Logic SCSI BIOS

 2MBit flash memory

1.1.2 System Health Monitor Functions

The system board is capable of monitoring the following system

health conditions.

 Monitors processor/system temperature and processor overheat

alarm

 Monitors 1.5V/3.3V/±5V/±12V/VCORE voltages and failure

alarm

 Monitors processor/chassis fan speed and failure alarm

 Automatic processor/chassis fan control

 Read back capability that displays temperature, voltage and fan

speed

Introduction

1.1.3 Intelligence

Automatic CPU/Chassis Fan Off

The CPU and chassis fans will automatically turn off once the

system enters the Suspend mode.

Dual Function Power Button

Depending on the setting in the BIOS setup, this switch will allow

the system to enter the Soft-Off or Suspend mode.

External Modem Ring-on

The Modem Ring-on feature allows the system that is in the

Suspend mode or Soft Power Off mode to wake-up/power-on to

respond to incoming calls.

Note:

This feature supports external modem only.

RTC Timer to Power-on the System

The RTC installed on the system board allows your system to

automatically power-on on the set date and time.

Wake-On-LAN Ready

The Wake-On-LAN function allows the network to remotely wake

up a Soft Power Down (Soft-Off) PC.Your LAN card must support

the remote wakeup function.

Important:

The 5VSB power source of your power supply must support

≥

720mA (minimum).

Wake-On-Keyboard/Wake-On-Mouse

This function allows you to use the keyboard or PS/2 mouse to

power-on the system. Refer to Jumper Settings for Wake-On-

Keyboard/Wake-On-Mouse in chapter 2 and Keyboard/Mouse

Power On in the Integrated Peripherals setup of the Award BIOS

in chapter 3 for more information.

Introduction

Important:

 The power button will not function once a keyboard

password has been set in the KB Power On Password

field of the Integrated Peripherals setup. You must type

the correct password to power-on the system.

 The 5VSB power source of your power supply must

support

≥

720mA (minimum).

ACPI

The system board is designed to meet the ACPI (Advanced

Configuration and Power Interface) specification. ACPI has energy

saving features that enable PCs to implement Power Management

and Plug-and-Play with operating systems that support OS Direct

Power Management.

Virus Protection

Most viruses today destroy data stored in hard drives. The system

board is designed to protect the boot sector and partition table of

your hard disk drive.

1.2 Package Checklist

The system board package contains the following items:

þThe system board

þA users manual

þOne IDE cable for ATA/33 or ATA/66 hard disk drives

þOne 34-pin floppy disk drive cable

þOne CD

If any of these items are missing or damaged, please contact your

dealer or sales representative for assistance.

Autres manuels pour CA61

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DFI Carte mère

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur