DFI AL051 Manuel utilisateur

AL051

Embedded SBC 2.5”

User’s Manual

A- 1469-M-2002

This publication contains information that is protected by copyright. No part of it may be re-

produced in any form or by any means or used to make any transformation/adaptation without

the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The manufacturer makes no

representations or warranties with respect to the contents or use of this manual and specifi-

cally disclaims any express or implied warranties of merchantability or fitness for any particular

purpose. The user will assume the entire risk of the use or the results of the use of this docu-

ment. Further, the manufacturer reserves the right to revise this publication and make changes

to its contents at any time, without obligation to notify any person or entity of such revisions

or changes.

Changes after the publication’s first release will be based on the product’s revision. The website

will always provide the most updated information.

Trademarks

Product names or trademarks appearing in this manual are for identification purpose only and

are the properties of the respective owners.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-

able protection against harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encour-

aged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission limits.

Table of Contents

Trademarks................................................ 2

FCC and DOC Statement on Class B ........... 2

Warranty ................................................... 4

Static Electricity Precautions ....................... 4

Safety Measures......................................... 4

About the Package..................................... 5

Optional Items........................................... 5

Before Using the System Board .................. 5

Chapter 1 - Introduction............................. 6

Specifications .................................................................. 6

Features ......................................................................... 7

Chapter 2 - Hardware Installation ............... 8

Board Layout .................................................................. 8

Block Diagram................................................................. 9

Mechanical Drawing......................................................... 9

System Memory .............................................................10

Installing the SODIMM Module ........................................ 10

Jumper Settings .............................................................11

Panel Power Select ........................................................ 11

M.2 Signal Select .......................................................... 12

Heat Spreader Assembly.................................................13

Rear Panel I/O Ports.......................................................15

2-Pin Terminal Block (DC 12V) ........................................ 15

Graphics Interfaces........................................................ 16

RJ45 LAN Ports ............................................................. 16

USB Ports ..................................................................... 17

I/O Connectors ..............................................................18

Digital I/O Connector ..................................................... 18

Front Audio Connector ................................................... 18

COM (Serial) Port .......................................................... 19

SATA (Serial ATA) Connector........................................... 20

Expansion Slots............................................................. 20

SMBus Connector .......................................................... 21

Front Panel Connector.................................................... 21

LVDS LCD Panel Connector ............................................. 22

LCD/Inverter & SATA Power Connector............................. 22

Battery......................................................................... 23

Chapter 3 - BIOS Setup.............................24

Overview .......................................................................24

Insyde BIOS Setup Utility ...............................................25

Main ............................................................................ 25

Advanced ..................................................................... 25

Security ....................................................................... 33

Boot ............................................................................ 33

Exit.............................................................................. 34

Updating the BIOS .........................................................35

Notice: BIOS SPI ROM....................................................35

Chapter 4 - Supported Software.................36

Appendix A - Troubleshooting Checklist.......42

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the product, in-

ability to use the product, unauthorized replacement or alteration of components and prod-

uct specifications.

2. The warranty is void if the product has been subjected to physical abuse, improper instal-

lation, modification, accidents or unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-

stances, attempt to perform service, adjustments or repairs on the product, whether in or

out of warranty. It must be returned to the purchase point, factory or authorized service

agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial damages to the

product that has been modified or altered.

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components or devices even

before installing them in your system unit. Static electrical discharge can damage computer

components without causing any signs of physical damage. You must take extra care in han-

dling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are

ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components, contacts

or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con-

nectors by their ends.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for installation or servic-

ing. After installation or servicing, cover the system chassis before plugging the power

cord.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and other com-

ponents. Perform the upgrade instruction procedures described at an ESD worksta-

tion only. If such a station is not available, you can provide some ESD protection by

wearing an antistatic wrist strap and attaching it to a metal part of the system chas-

sis. If a wrist strap is unavailable, establish and maintain contact with the system

chassis throughout any procedures requiring ESD protection.

About the Package

The package contains the following items. If any of these items are missing or damaged,

please contact your dealer or sales representative for assistance.

• One AL051 board

• One Serial ATA data cable (Length: 155mm)

• One Y cable for SATA and inverter power (Length: 155mm)

• One Heat spreader (Height: 11mm)

Optional Items

• USB port cable (Length: 200mm)

• COM port cable (Length: 300mm)

• Power adapter (60W, 12V, DC Jack)

• 2-pole terminal to DC Jack cable

• Audio cable (Length: 160mm)

• Heat sink for E series CPU 0 to 60°C/wide temp (Height: 22.6mm)

• Heat sink for N series CPU 0 to 60°C (Height: 19mm)

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance to the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need at least the following

internal components.

• Storage devices such as hard disk drive, etc.

You will also need external system peripherals you intend to use which will normally include at

least a keyboard, a mouse and a video display monitor.

Chapter 1 - Introduction

Specications

Chapter 1

Chapter 1 Introduction www.d.com

SYSTEM Processor Intel Atom®Processor E3900 Family, BGA 1296

Intel Atom®x7-E3950 Processor, Quad Core, 2M Cache, 1.6GHz (2.0GHz), 12W

Intel Atom®x5-E3940 Processor, Quad Core, 2M Cache, 1.6GHz (1.8GHz), 9.5W

Intel Atom®x5-E3930 Processor, Dual Core, 2M Cache, 1.3GHz (1.8GHz), 6.5W

Intel®Pentium®Processor N4200, Quad Core, 2M Cache, 1.1GHz (2.5GHz), 6W

Intel®Celeron®Processor N3350, Dual Core, 2M Cache, 1.1GHz (2.4GHz), 6W

Memory One 204-pin SODIMM up to 8GB

Single Channel DDR3L 1866MHz

BIOS Insyde SPI 64Mbit (supports UEFI boot only)

GRAPHICS Controller Intel®HD Graphics

Feature OpenGL 4.2, Direct X 11.1, OpenCL 1.2, OGL ES 3.0

HW Decode: H.264, MPEG2, VC1, VP8, H.265, MPEG4

HW Encode: H.264, MPEG2, MPEG4

Display 1 x Mini DP++

1 x VGA

1 x LVDS

Mini DP++: resolution up to 4096x2160 @ 60Hz

VGA: resolution up to 1920x1200 @ 60Hz

LVDS: dual channel 18/24-bit, resolution up to 1920x1200 @ 60Hz

Triple

Displays

VGA + Mini DP++ + LVDS

EXPANSION Interface 1 x Full-size Mini PCIe (PCIe/USB 2.0, optional USB 3.1 Gen 1/USB 2.0)

1 x M.2 B key 2242 (PCIe/USB 2.0/SATA 3.0)

AUDIO Audio

Codec

Realtek ALC888S-VC2-GR

ETHERNET Controller 2 x Intel®I211AT PCIe (10/100/1000Mbps)

2 x Intel®I210IT PCIe (10/100/1000Mbps) (available upon request)

REAR I/O Ethernet 2 x GbE (RJ-45)

USB 2 x USB 3.1 Gen 1

Display 1 x Mini DP++

1 x VGA

1 x LVDS

INTERNAL I/O Serial 1 x RS-232/422/485 (1.27mm pitch)

USB 2 x USB 2.0 (1.27mm pitch)

Display 1 x LVDS LCD Panel Connector

Audio 1 x Audio (Line-out/Mic-in)

SATA 1 x SATA 3.0 (up to 6Gb/s)

DIO 1 x 8-bit DIO

SMBus 1 x SMBus

WATCHDOG

TIMER

Output &

Interval

System Reset, Programmable via Software from 1 to 255 Seconds

SECURITY TPM fTPM2.0

POWER Type Single 12V +/-10% DC

Connector 2-pin Terminal Block

2-pin Vertical Type Connector (opt.)

RTC Battery CR2032 Coin Cell

Consumption Typical: E3950:12V @ 0.51A (6.12Watt)

Max.: E3950:12V @ 2.00A (24.00Watt)

OS SUPPORT

(UEFI ONLY)

Microsoft/Linux Windows 10 IoT Enterprise (64-bit)

Ubuntu 16.04

ENVIRONMENT Temperature Operating: 0 to 60°C, Option: -20 to 70°C/-40 to 85°C

Storage: -40 to 85°C

Humidity Operating: 5 to 90% RH

Storage: 5 to 90% RH

MTBF 497,857 hrs @ 25°C; 318,774 hrs @ 45°C; 213,436 hrs @ 60°C

MECHANICAL Dimensions 2.5" Pico-ITX Form Factor

100mm (3.94") x 72mm (2.83")

Height PCB: 1.6mm

Top Side: 15mm, Bottom Side: 8mm

CERTIFICATIONS CE, FCC, RoHS

Chapter 1

Chapter 1 Introduction www.d.com

Features

•Watchdog Timer

The Watchdog Timer function allows your application to regularly “clear” the system at the set

time interval. If the system hangs or fails to function, it will reset at the set time interval so

that your system will continue to operate.

• DDR3L

DDR3L SDRAM provides backward compatibility to DDR3 memory modules but can operate at

the same or at a lower power level.

• Graphics

The integrated Intel®HD graphics engine delivers an excellent blend of graphics performance

and features to meet business needs. It provides excellent video and 3D graphics with out-

standing graphics responsiveness. These enhancements deliver the performance and compat-

ibility needed for today’s and tomorrow’s business applications. Supports 1 x Mini DP++, 1 x

VGA and 1 x LVDS interfaces for triple display outputs.

•Serial ATA

Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of

up to 6Gb/s (SATA 3.0), it improves hard drive performance faster than the standard parallel

ATA whose data transfer rate is 100MB/s.

•Gigabit LAN

Two Intel®I211AT PCI Express Gigabit Ethernet controllers or two optional Intel®I210IT PCI

Express Gigabit Ethernet controllers support up to 1Gbps data transmission.

• Audio

The Realtek ALC888S-VC2-GR audio codec provides 2.1-channel High Definition audio output.

•Power Failure Recovery

When power returns after an AC power failure, you may choose to either power-on the system

manually or let the system power-on automatically.

• USB

The system board supports the USB 3.1 Gen 1. It is capable of running at a maximum trans-

mission speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60

MB/s) and USB 1.1 (12Mb/s). USB 3.1 Gen 1 reduces the time required for data transmission,

reduces power consumption, and is backward compatible with USB 2.0. It is a marked im-

provement in device transfer speeds between your computer and a wide range of simultane-

ously accessible external Plug and Play peripherals.

• Wake-On-LAN

This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is

supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Man-

agement Event) signal. However, if your system is in the Suspend mode, you can power-on

the system only through an IRQ or DMA interrupt.

•ACPI STR

The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)

specification. ACPI has energy saving features that enable PCs to implement power manage-

ment and plug-and-play with operating systems that support power management features.

With ACPI, the system can further utilize the Ethernet adapter’s wake-on-LAN (WOL) capability

that enables remote wake-up if the Ethernet adapter supports such feature.

www.dﬁ.com

Chapter 2 Hardware Installation

Chapter 2

Chapter 2 - Hardware Installation

Board Layout

Top View Bottom View

PTN3460

USB 0-1

USB 3.1 Gen 1 Mini DP++

SPI

Flash

BIOS

Mini PCIe

SATA 3.0

SATA 0

10 2

LAN 1

M.2 B Key

39 40

USB 2-3

USB 2.0

Realtek

ALC888S

LAN 2

VGA

2-Pin Terminal Block

(DC 12V)

LCD/Inverter

& SATA Power

Panel Power

Select (JP2)

LVDS

LCD

Panel

Front

Audio

SMBus

COM 1

M.2 Signal

Select (JP5)

Battery

Intel I211AT

I210IT (opt.)

Intel I211AT

I210IT (opt.)

Front

Panel

210

DIO

DDR3L_ SODIMM

Intel

Atom

E3900 Series

F81803

Buzzer

Standby

Power LED

www.dﬁ.com

Chapter 2 Hardware Installation

Chapter 2

Block Diagram

Intel Atom

Processor

E3900 Series

Super IO

with WDT

Digital I/O 8-bit

DDR3L 1866MHz

SODIMM

Channel A

M.2 1x

PCIe x1

(USB 3.1 Gen1 x1 opt.)

DDI

LPC Bus

SMBus

SPI

Full-size

Mini PCIe

SATA 3.0

USB 2.0

USB 3.1 Gen 1/2.0 2x

USB 3.1 Gen 1

USB 2.0

USB 2.0 2x USB 2.0

SATA 3.0 SATA 1x

HD Audio

(Line-out, Mic-in)

PCIe x1

USB 2.0

I211AT PCIe x1

GLAN 1

Mini DP++

VGA IT6516

I210 IT

(opt.)

I211AT PCIe x1

GLAN 2

I210 IT

(opt.)

RS232/422/485 1x

PTN3460

eDP LVDS

Mechanical Drawing

2.97

13.45

31.13

58.50

85.13

97.05

100

3.04

22.22

69.08

www.dﬁ.com

Chapter 2 Hardware Installation

Chapter 2

System Memory

Important:

Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in

boards, and other components. Perform installation procedures at an ESD workstation

only. If such a station is not available, you can provide some ESD protection by wear-

ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If

a wrist strap is unavailable, establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Important:

When the Standby Power LED lights red, it indicates that there is power on the sys-

tem board. Power-off the PC then unplug the power cord prior to installing any de-

vices. Failure to do so will cause severe damage to the motherboard and components.

• One 204-pin SODIMM up to 8GB

• Single Channel DDR3L 1866MHz

Features

DDR3L

Standby Power LED

Installing the SODIMM Module

1. Make sure the PC and all other peripheral devices connected to it has been powered down.

2. Disconnect all power cords and cables.

3. Locate the SODIMM socket on the system board.

4. Note the key on the socket. The key ensures the module can be plugged into the socket in

only one direction.

Note:

The system board used in the following illustrations may not resemble the actual

board. These illustrations are for reference only.

Table des matières

Autres manuels DFI Carte mère

DFI

DFI PR611-C621 Manuel utilisateur

DFI

DFI HD310-Q87 Manuel utilisateur

DFI

DFI BW171 Manuel utilisateur

DFI

DFI CS650-C246 Manuel utilisateur

DFI

DFI G586IPV Manuel utilisateur

DFI

DFI NS70-EC Manuel utilisateur

DFI

DFI KD600-H110/Q170 Manuel utilisateur

DFI

DFI CS100-Q370 Manuel utilisateur

DFI

DFI 686IPK Manuel utilisateur

DFI

DFI GIC68-D Manuel utilisateur

DFI

DFI CS101-H310 Manuel utilisateur

DFI

DFI SR100-N Manuel utilisateur

DFI

DFI ADS310-R680E Series Manuel utilisateur

DFI

DFI 845GV-MLV Manuel utilisateur

DFI

DFI AD75 Manuel utilisateur

DFI

DFI CA63-SC Manuel utilisateur

DFI

DFI 845PE-ML Manuel utilisateur

DFI

DFI G7L330-B Manuel utilisateur

DFI

DFI CA63-SN Manuel utilisateur

DFI

DFI ADS310-R680E/Q670E Manuel utilisateur

DFI

DFI PB61-V3 Manuel utilisateur

DFI

DFI G4H875-P Manuel utilisateur

DFI

DFI OT951-D Series Manuel utilisateur

DFI

DFI CS331-C246 Manuel utilisateur

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur