DFI ES220F-CS Manuel utilisateur

© May 12, 2023 DFI Inc.

www.dfi.com

ES220F-CS

Compact Fanless Embedded System

Quick Installation Guide

Package Contents

• 1 ES220F-CS system unit with wallmount

• Adapter 12V 60W (optional)

• Power Cord 1830mm (optional)

• VESA mounting kit (optional)

Quick Reference | ES220F-CS 1

Product Overview

Front View - 1 storage

Front View - 3 storage

1

2

3

4

5

Power Button

Status LED, Reset Button

HDMI 2.0

USB 3.1

LAN 1 & LAN 2

2

1345

2

1345

Quick Reference | ES220F-CS 2

Rear View - 1 storage

Rear View - 3 storage

6

78910

6

78910

8

9

10

Grounding Hole

COM 1

COM 2

USB 2.0

DC-in

6

7

Removing the Chassis Cover

Please observe the following guidelines and follow the instructions to open the system.

1.

Make sure the system and all other peripheral devices connected to it have been

powered off.

2. Disconnect all power cords and cables.

Step 1:

To remove the top cover - The 8 screws on the top of the system

are used to secure the

cover

to

the

chassis. Remove the screws and put them in a safe place for later use. And then lift up

the cover to remove it.

To remove the bottom cover - The 2 screws on the bottom of the system

are used to secure

the

cover

to

the

chassis. Remove the screws and put them in a safe place for later use. And

then tilt up the cover to remove it.

Bottom ViewTop View

Step 2:

Lift the cover to open the system.

Quick Reference | ES220F-CS 3

Step 3:

The board can be easily accessed after the chassis cover is removed.

Bottom View

Top View

Quick Reference | ES220F-CS 4

Installing an M.2 Card

Please observe the following guidelines and follow the instructions to open the system.

1.

Make sure the system and all other peripheral devices connected to it have been

powered off.

2. Disconnect all power cords and cables.

Step 1:

The 2 screws on the bottom of the system

are used to secure the

cover

to

the

chassis.

Remove the screws and put them in a safe place for later use.

Lift the cover to open the system. M.2 card slots can be easily accessed after the chassis

cover is removed.

M.2-M

M.2-E

Quick Reference | ES220F-CS 5

M.2 Module M.2 Socket

Key

Stand-off

Notch

Step 4:

Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap

between the card and the stand-off closes up. The card should be lying parallel to the board

when it’s correctly mounted.

Step 3:

Press the end of the card far from the socket down until against the stand-off.

M.2 Module M.2 Socket

Key

Stand-off

Notch

M.2 Module M.2 Socket

Key

Stand-off

Notch

Step 2:

Please follow the steps below to install the card into the socket.

Insert the card into the socket at an angle while making sure the notch and key are perfectly

aligned.

Quick Reference | ES220F-CS 6

Before installing the antenna, please make sure that the following safety cautions are

wellattended

.

1. Make sure the PC and all other peripheral devices connected to it have been

powered

down

.

2. Disconnect all power cords and cables.

Step 1:

There are antenna holes reserved on the front and back side of the system and covered by 4

knockout tabs. Please remove the knockout tabs prior to installing an antenna.

Knockout tabs for Antenna Hole

Knockout tabs for Antenna Hole

Installing an Antenna

Quick Reference | ES220F-CS 7

Step 2:

Use a flathead screwdriver and apply a little extra force to detach a knockout tab until it breaks

off from the system.

Once the knockout tab is mostly detached, it will pretty quickly snap off, leaving you a nice hole

for installing an antenna.

Step 3:

Connect the internal cable to the board's antenna connector, screw the antenna connector

through the antenna hole with washers and nuts, and screw on the antenna as illustrated

below.

Antenna ConnectorCableModule Connector NutWasher

Chassis Wall Antenna

Quick Reference | ES220F-CS 8

Wall Mount

The wall mount kit containing two mounting brackets — purchased as optional items — can

be attached to the bottom of the system for mounting onto desired locations, such as walls,

stands, or shelves. Locate the mounting holes on the bottom of the system as shown in the

photo. Screw on the two brackets onto the system with four screws as illustrated below.

Wall Mount Bracket

Wall Mount Bracket

ES220F-CS 1 storage as an example:

Quick Reference | ES220F-CS 9

Autres manuels pour ES220F-CS

1

Table des matières

Autres manuels DFI PC industriel

Manuels PC industriel populaires d'autres marques

Chipsee

Chipsee PPC-A72-101 Manuel utilisateur

Advantech

Advantech UNO-2184G Manuel utilisateur

MSI

MSI MS-9A76 Manuel utilisateur

Stackrack

Stackrack THOR200 Manuel utilisateur

Moxa Technologies

Moxa Technologies DA-682C Series Manuel utilisateur

Nodka

Nodka eBOX-3000-ETC Manuel utilisateur

Siemens

Siemens SIMATIC IPC627E Manuel utilisateur

MSI

MSI MS-9A89 Manuel utilisateur

Artila

Artila Matrix-516 Manuel utilisateur

Siemens

Siemens SIMATIC Rack PC 840 V2 Manuel utilisateur

Advantech

Advantech IPPC-6152A Manuel utilisateur

Beckhoff

Beckhoff CX9020 Manuel utilisateur

Dell

Dell Embedded Box PC 5000 Manuel utilisateur

IBASE Technology

IBASE Technology ASB200-918 Series Manuel utilisateur

Lenovo

Lenovo ThinkCentre M90q Manuel du propriétaire

IXXAT

IXXAT Econ 100 Manuel utilisateur

Kontron

Kontron KBox A-151-TGL Manuel utilisateur

AXIOMTEK

AXIOMTEK ICO500-518 Series Manuel utilisateur