DFI EC500-KH Manuel utilisateur

1

EC500-KH Installation Guide

Package Contents

DFI reserves the right to change the specications at any time prior to the product's release. For the latest revision and details of the

installation procedure, please refer to the user's manual.

www.d.com

•

One EC500-KH system unit

• Mounting screws for SATA drive

•

Mounting screws for Mini PCIe and M.2 modules

•

1 Quick Installation Guide

•

1 CD disk includes:

- Drivers / Manual

Panel

Rear View

Front View

COM 2

Power Button

Reset Button

USB 2.0 COM 3

Status LED (Orange)

HDD LED (Red)

COM 1

Extended Power

on/off Switch

COM 4

Antenna holesAntenna holes Antenna holes

Note:

This port can be in HDMI or DP++ (DP++ available upon request).

DC-in USB 3.0

DVI-D

(DVI-I connector)

CFast LAN 1

LAN 2 VGA

Line-out

HDMI*

Microphone

2

Removing the Chassis Cover

Please observe the following guidelines before starting any installation procedures.

1. Make sure the system and all other peripherals connected to it have been

powered off.

2. Disconnect all power cords and cables.

To open the system, remove the 6 mounting screws on the on the left side, right

side and bottom of the system. Put them in a safe place for later use.

Mounting Screw

Mounting Screw

3

4. The SODIMM sockets, Mini PCIe and M.2 slots and SATA drive bay can be

easily accessed after the chassis cover is removed.

3. Lift the cover upward to open the system.

SODIMM socket

Mini PCIe slot

SATA drive bay

M.2 slot

SIM card slot

4

Installing a SODIMM

Grasp the memory module by its edges and align the module’s notch with

the socket’s notch; then insert the memory into the socket at an angle and

push it down until you feel a click.

SODIMM module

installed into the

socket

Notes:

1. The system supports dual-channel conguration. To enable dual-channel,

populate both SODIMM sockets.

2. If installing only one memory module, please install it on the memory socket

labeled DIMM 1 (the one closer to the center of the board).

3. The SODIMM sockets can only accept DDR4 memory modules. Please do not

install other types of memory modules. The SKUs with Intel® CM238 Chipset

support ECC memory.

Insert the memory

at an angle

5

Installing an M.2 Card

To install an M.2 card, insert the bottom edge of the M.2 card into the

connector, and then secure the card to the standoff with the provided

mounting screw.

Mounting Screw

The onboard M.2 Type 2280 connector (M Key) supports PCIe NVMe modules

up to PCIe Gen 3.0 x4 bandwidth. Note that only SKUs with Intel®QM175

Chipset support M.2 socket.

6

Installing a 2.5” SATA Drive

Mounting Screws

Mounting screws

SATA data and power cable

2. Place the SATA drive installed with the HDD bracket in the system. Align the

mounting holes on the HDD bracket with the mounting holes on the drive

bay and use the provided mounting screws to secure the drive in place.

Mounting Screws

Mounting screws

1. Before installing the SATA drive, connect the SATA data and power cable to

the SATA data connector of the SATA drive. Then install the SATA drive onto

the HDD bracket with the provided mounting screws.

The system can accommodate one SATA drive. Please use the following procedure

to install a SATA drive in the system.

7

3. Connect the other end of the SATA data and power cable to the SATA data

and power connectors on the system board respectively.

SATA data connector

SATA power connector

8

Installing a CFast Card

1.

Before installing a CFast card, take off the CFast card slot cover.

2. Gently insert the CFast card straight with the label on the CFast card facing

up until you feel it lock into place. Do not force the card into the slot if the

card is not correctly inserted.

3. Close the CFast card cover. To eject the card, push the card inward to

release the lock and pull it out.

CFast installed

The CFast slot is located on the rear panel and can be accessed without opening

the system chassis.

CFast slot cover

9

Installing a Mini PCIe Card and a SIM Card

The system board is equipped with 2 Mini PCIe slots with SIM card sockets to

support a variety of wireless LAN and mobile broadband communication modules.

Mini PCIe slot 1 provides both USB and PCIe interfaces whereas Mini PCIe slot 2

provides only USB interface.

1. Grasp the Mini PCIe card by its edges and align the notch in the connector of

the Mini PCIe card with the notch in the connector on the system board.

2. Push the Mini PCIe card down and use the provided mounting screws to

secure the card on the system board.

Mounting screws

Antenna holes

10

Installing a SIM Card

Open the SIM card socket by pushing the white latch inward.

Insert the SIM card into the slot. Please place the card with the IC facing down

and the angled corner aligning with the socket's angled corner so it will be cor-

rectly in contact with the system board.

Close the slot's cover and lock the slot by pushing the white latch outward.

Push the latch inward

to open it

Flip the cover up to open it

Close the cover the lock it

Table des matières

Autres manuels DFI PC industriel

Manuels PC industriel populaires d'autres marques

Chipsee

Chipsee PPC-A72-101 Manuel utilisateur

Advantech

Advantech UNO-2184G Manuel utilisateur

MSI

MSI MS-9A76 Manuel utilisateur

Stackrack

Stackrack THOR200 Manuel utilisateur

Moxa Technologies

Moxa Technologies DA-682C Series Manuel utilisateur

Nodka

Nodka eBOX-3000-ETC Manuel utilisateur

Siemens

Siemens SIMATIC IPC627E Manuel utilisateur

MSI

MSI MS-9A89 Manuel utilisateur

Artila

Artila Matrix-516 Manuel utilisateur

Siemens

Siemens SIMATIC Rack PC 840 V2 Manuel utilisateur

Advantech

Advantech IPPC-6152A Manuel utilisateur

Beckhoff

Beckhoff CX9020 Manuel utilisateur

Dell

Dell Embedded Box PC 5000 Manuel utilisateur

IBASE Technology

IBASE Technology ASB200-918 Series Manuel utilisateur

Lenovo

Lenovo ThinkCentre M90q Manuel du propriétaire

IXXAT

IXXAT Econ 100 Manuel utilisateur

Kontron

Kontron KBox A-151-TGL Manuel utilisateur

AXIOMTEK

AXIOMTEK ICO500-518 Series Manuel utilisateur