DFI PCSF51 Manuel utilisateur

G2 G1

M2 M1

10 2

L1 L3L2 L4

3 1

S3 S4

11 6

1 2 3 7 8 9

M2CN1-G3

U314

U312

CN7

CN6

J11

SW1

SW2

J12

CN10

CN1

J3000

Q28

Q26

U135

SC110

U303

U333

U121

CN3

U334

LC804

U307

SC10

SYS_FAN

M.2-E

BAT

SPI

LAN1

USB-C_1/2

M.2 E Key

DDR

10 2

1 2

345

Top View

Board Layout

www.dfi.com

PCSF51

Quick Reference

410

511

Reset Button

Power Button

HDMI

LAN

USB3.1 Type A

CMOS Battery

SPI

System Fan

DC Power Connector

DIO Header

UART Debug

DDR

eMMC

Bottom View

Quick Reference | PCSF51 1

Led Indicator

Buzzer

PIN Assignment

XUART Debug

XDC Power Connector

XSystem Fan

Pin Assignment

1GND

2UART_TX

Pin Assignment

1DC-IN

2GND

Pin Assignment

1NC

212VSB

3GND

XDIO Header

Pin Assignment

1GND

25VSB

3DIO0

4DIO1

5DIO2

6DIO3

7DIO4

8DIO5

9DIO6

10 DIO7

Quick Reference | PCSF51 2

Assembly

A heat spreader is included in the standard package. The heat spreader and components

required for mounting are illustrated below.

The heat spreader is designed to be mounted onto the module as illustrated below. Please

make sure the contacting sides of the heat spreader and the module are correct — the CPU

side of the module shall be facing the interface metal side and legs of the heat spreader.

Rotate horozontally so the interface metal sits right on top of the CPU. Remove any plastic

cover on the interface metal and apply thermal paste/adhesive if it is required.

Screw * 4

Interface Metal

Interface Metal Side Down

CPU Side Up

Quick Reference | PCSF51 3

Module side to chassis Heat spreader side to chassis

Rotate the module and heat spreader combo so that the I/O is facing the desired side, and

place the combo in the position of the chassis reserved for your module.

Align the screw holes of the combo to those on the chassis. The combo can be mounted

onto the chassis in two manners — 1) module side to the chassis, or 2) heat spreader side to

the chassis as illustrated below. This shall depend entirely on the design of the chassis with

regard to interior spacing, thermal, and I/O.

Place the screws that come with the standard package into the screw holes, and use a screw

driver to fasten the screws until the combo is securely fixed onto the chassis.

To Chassis

Chassis

To Chassis

Chassis

DFI reserves the right to change the specifications at any

time prior to the product's release. This QR may be based

on the product’s revision. For more documentation and

drivers, please visit the download page at www.dfi.com/

downloadcenter, or via the QR codes to the right.

Quick Reference | PCSF51 4

Autres manuels pour PCSF51

Table des matières

Autres manuels DFI Matériel informatique

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur