DFI-ITOX SR330-L Manuel utilisateur

SR330-L

SR330-L20C

System Board

User’s Manual

935-SR3301-500G

A07010026

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior writ-

ten permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any ex-

press or implied warranties of merchantability or fitness for any par-

ticular purpose.The user will assume the entire risk of the use or the

results of the use of this document. Further, the manufacturer re-

serves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or en-

tity of such revisions or changes.

Trademarks

Product names or trademarks appearing in this manual are for iden-

tification purpose only and are the properties of the respective own-

ers.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation.This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following meas-

ures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

About this Manual................................................................................

Warranty.................................................................................................

Static Electricity Precaution................................................................

Safety Measures.....................................................................................

About the Package...............................................................................

Before Using the System Board.........................................................

Chapter 1 - Introduction....................................................................

Specifications...................................................................................................................................

Features..............................................................................................................................................

Chapter 2 - Hardware Installation....................................................

System Board Layout ..........................................................................................................

System Memory..........................................................................................................................

CPU.......................................................................................................................................................

Jumper Settings............................................................................................................................

Rear Panel I/O Ports.............................................................................................................

I/O Connectors..........................................................................................................................

SPI Flash ROM Socket.........................................................................................................

Chapter 3 - BIOS Setup......................................................................

Overview...........................................................................................................................................

Updating the BIOS..................................................................................................................

Chapter 4 - Supported Softwares.....................................................

Drivers for Windows 7 / Windows Vista System.....................................

Drivers for Windows XP System..............................................................................

Appendix A - NLITE and AHCI Installation Guide..........................

Appendix B - Watchdog Timer.............................................................

Appendix C - Troubleshooting..........................................................

Appendix D - Frequently Asked Questions...................................

Appendix E - Hot Keys for Graphics Displays..............................

114

129

141

143

147

149

About this Manual

An electronic file of this manual is included in the CD. To view the

user’s manual in the CD, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product specifica-

tions.

2. The warranty is void if the product has been subjected to physi-

cal abuse, improper installation, modification, accidents or unau-

thorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service, adjust-

ments or repairs on the product, whether in or out of warranty.

It must be returned to the purchase point, factory or authorized

service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board,

components or devices even before installing them in your system

unit. Static electrical discharge can damage computer components

without causing any signs of physical damage. You must take extra

care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its

anti-static bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of

the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connec-

tors. Hold modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor,

disk drive and other components. Perform the upgrade in-

struction procedures described at an ESD workstation

only. If such a station is not available, you can provide

some ESD protection by wearing an antistatic wrist strap

and attaching it to a metal part of the system chassis. If a

wrist strap is unavailable, establish and maintain contact

with the system chassis throughout any procedures requir-

ing ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to local ordinance.

Introduction

About the Package

The system board package contains the following items. If any of

these items are missing or damaged, please contact your dealer or

sales representative for assistance.

;The system board

;A user’s manual

;One IDE cable

;One FDD cable

;One USB cable

;One Serial ATA data cable

;One Serial ATA power cable

;One “Main Board Utility” CD

;Two floppy diskettes

;One I/O shield

;One QR (Quick Reference)

The system board and accessories in the package may not come

similar to the information listed above.This may differ in accordance

to the sales region or models in which it was sold. For more infor-

mation about the standard package in your region, please contact

your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need

at least the following internal components.

•A CPU

•Memory module

•Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use

which will normally include at least a keyboard, a mouse and a video

display monitor.

Introduction

Processor

Chipset

System Memory

Expansion Slots

Graphics

Audio

LAN

Serial ATA

IDE

Chapter 1 - Introduction

Specifications

• SR330-L20C

- Intel®Celeron®M 550 2.0GHz 1MB cache mobile processor

(bundled with board)

• SR330-L

- Intel®Celeron®M 500 series processor

• 533MHz system data bus

• Processor socket: mPGA478P

• Intel®chipset

- Intel®GLE960 Express chipset

- Intel®ICH8M

• Two 240-pin DDR2 DIMM sockets

• Supports 533MHz DDR2 SDRAM

• Supports maximum of 2GB system memory

• 1 PCI Express x4 slot

• 2 PCI slots

• Internal graphics feature

- Mobile Intel®Graphics Media Accelerator X3100

- Dynamic Video Memory Technology 4.0

- Microsoft DirectX 9x

- OpenGL 1.5

• Integrated graphics interface

- Analog CRT

- 400MHz core render clock

- Analog monitor supports up to QXGA (2048x1536@60Hz)

- DVI (supports DVI-D signal only)

- DVI 1.0 support for external digital monitor

• Realtek ALC262 2-channel High Definition Audio

• Two 24-bit stereo DACs and three 20-bit stereo ADCs

• S/PDIF input/output interface

• One Realtek RTL8111C PCI Express Gigabit controller

• Supports 10Mbps, 100Mbps and 1Gbps data transmission

• IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) compliant

• Three Serial ATA ports, compliant with SATA 1.0a

specification

• Data transfer rate up to 3Gb/s

• Supports Advanced Host Controller Interface (AHCI)

• Supports up to two IDE devices

• Supports Ultra ATA 100/66/33

Introduction

Rear Panel I/O

Ports

I/O Connectors

BIOS

Energy Efficient

Design

Damage Free

Intelligence

Temperature

Humidity

PCB

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 2 DB-9 serial ports

• 1 DB-15 VGA port

• 1 DVI-I port (DVI-D signal only)

• 1 RJ45 LAN port

• 4 USB 2.0/1.1 ports

• Mic-in, line-in and line out jacks

• 3 connectors for 6 additional external USB 2.0/1.1 ports

• 1 front audio connector for line-out and mic-in jacks

• 1 CD-in internal audio connector

• 1 S/PDIF connector

• 3 Serial ATA connectors

• 1 40-pin IDE connector

• 1 FDD connector

• 1 parallel connector

• 1 IrDA connector

• 1 24-pin ATX power connector

• 1 front panel connector

• 1 chassis intrusion connector

• 3 fan connectors

• Award BIOS

• 8Mbit SPI flash memory

• Supports ACPI specification 2.0/1.0

• Wake-On-Events include:

- Wake-On-PS/2 Keyboard/Mouse

- Wake-On-USB Keyboard/Mouse

- PCI Express PME

- Wake up by PCI card

- Wake-On-Ring

- RTC timer to power-on the system

• Enhanced Intel®SpeedStep Technology

• AC power failure recovery

• Monitors CPU/system temperature and overheat alarm

• Monitors CPU(V)/3.3V/5V/12V/VBAT(V)/5VSB(V) voltages and

failure alarm

• Monitors CPU/system/2nd fan speed and failure alarm

• Read back capability that displays temperature, voltage and fan

speed

• Watchdog timer function

•0

oC to 60oC

• 10% to 90%

• 6-layers, microATX form factor

• 24.4cm (9.6") x 24.4cm (9.6")

Introduction

Features

The Watchdog Timer function allows your

application to regularly “clear” the system at

the set time interval. If the system hangs or fails to function, it will

reset at the set time interval so that your system will continue to

operate.

DDR2 is a higher performance DDR technology

whose data transfer rate delivers bandwidth of 4.3

GB per second and beyond. That is twice the speed of the conven-

tional DDR without increasing its power consumption. DDR2

SDRAM modules work at 1.8V supply compared to 2.6V memory

voltage for DDR modules. DDR2 also incorporates new innovations

such as the On-Die Termination (ODT) as well as larger 4-bit pre-

fetch against DDR which fetches 2 bits per clock cycle.

The Intel northbridge chip comes integrated with the

Intel Graphics Media Accelerator X3100 delivering

exceptional 3D graphics performance. It supports analog CRT and

DVI interfaces.

DVI (Digital Visual Interface) is a form of video inter-

face technology made to maximize the quality of flat

panel LCD monitors and modern video graphics cards. Data is

transmitted using the TMDS (Transition Minimized Differential

Signaling) protocol, providing a digital signal from the PC’s graphics

subsystem to the display.

S/PDIF is a standard audio file transfer format that

transfers digital audio signals to a device without

having to be converted first to an analog format. This prevents the

quality of the audio signal from degrading whenever it is converted

to analog. S/PDIF is usually found on digital audio equipment such as

a DAT machine or audio processing device.The S/PDIF connector on

the system board sends surround sound and 3D audio signal out-

puts to amplifiers and speakers and to digital recording devices like

CD recorders.

watchdog timer

DDR2

graphics

DVI

S/PDIF

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DFI-ITOX Carte mère

DFI-ITOX

DFI-ITOX EL330-DR Manuel utilisateur

DFI-ITOX

DFI-ITOX G4C600-R Manuel utilisateur

DFI-ITOX

DFI-ITOX SR100-N Manuel utilisateur

DFI-ITOX

DFI-ITOX CB60-ZX Manuel utilisateur

DFI-ITOX

DFI-ITOX G7VP2 Manuel utilisateur

DFI-ITOX

DFI-ITOX LR101 SERIES Manuel utilisateur

DFI-ITOX

DFI-ITOX G7VP2 Manuel utilisateur

DFI-ITOX

DFI-ITOX EL332-IP Manuel utilisateur

DFI-ITOX

DFI-ITOX NP100-N16C Manuel utilisateur

DFI-ITOX

DFI-ITOX SB100-NRM Manuel utilisateur

DFI-ITOX

DFI-ITOX G4S600-B Manuel utilisateur

DFI-ITOX

DFI-ITOX G4V300-D Manuel utilisateur

DFI-ITOX

DFI-ITOX EL109-N Manuel utilisateur

DFI-ITOX

DFI-ITOX G4M300-M12 Manuel utilisateur

DFI-ITOX

DFI-ITOX G7B630-B Manuel utilisateur

DFI-ITOX

DFI-ITOX CA61 Manuel utilisateur

DFI-ITOX

DFI-ITOX G4V620-N Manuel utilisateur

DFI-ITOX

DFI-ITOX G7V300-P Manuel utilisateur

DFI-ITOX

DFI-ITOX G4S300-B Manuel utilisateur

DFI-ITOX

DFI-ITOX G5G100-P Manuel utilisateur

DFI-ITOX

DFI-ITOX EL330-DR Manuel utilisateur

DFI-ITOX

DFI-ITOX G4H875-N Manuel utilisateur

DFI-ITOX

DFI-ITOX 586ITOX Manuel utilisateur

DFI-ITOX

DFI-ITOX LT600-DR Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur