Denver CR-718 Manuel utilisateur
INSTRUCTION MANUAL
BRUKSANVISNING
BETJENINGSVEJLEDNING
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUAL DE INSTRUÇÕES
INSTRUCCIONES DE U SO
KÄYTTÖOHJEET
GEBRUIKERSHANDLEIDING
INSTRUKCJA OBSŁUGI
PRIRUČNIK ZA RUKOVANJE
www.denver-electronics.com
www.facebook.com/denverelectronics
CR-718
ENGLISH
FUNCTION AND CONTROLS
1. SNOOZE / SLEEP / DIMMER
2. DISPLAY
3. PM INDICATOR
4. STANDBY INDICATOR
5. ALARM 1 INDICATOR
6. ALARM 1 ON / OFF SET
7. ALARM 2 ON / OFF SET
8. << / TUNE - / YEAR/MONTH/DAY / C-F
9. >> / TUNE + / DST
10. VOLUME DOWN / DISPLAY LIGHT AUTO ON-OFF
11. VOLUME UP / TOGGLE BETWEEN DISPLAY CONTENTS ON-
OFF
12. CLOCK ADJ. / MEM.SET / M+ / NAP
13. ON / OFF RADIO / ALARM OFF
14. WEATHER FORECAST
15. ALARM 2 INDICATOR
16. TEMPERATURE SENSOR (IN DOOR) / HUMIDITY SENSOR
17. AC POWER CORD
18. FM ANTENNA
19. SPEAKER
20. BATTERY COMPARTMENT
21. RATING LABEL
LED DISPLAY MODE
POWER CONNECTION
Plug the AC power cord to a household outlet AC source. This unit
is equipped with a battery back up system, it requires a 3V CR2032
at lithium battery (not included). Insert the battery in the battery
compartment, making certain that the positive and negative (+ and -)
battery terminals are attached to the corresponding terminals on the
plate in the battery compartment. If an AC power failure occurs, the
clock automatically switches to the battery power supply, the clock and
timer memory continue running. When the AC power resumes, the
clock switches back to AC again.
TIME
TIME AND CALENDAR MANUAL SETTING
Setting Time and Calendar
Press Clock ADJ. (12) button in standby mode and keep depress over
2 seconds to enter time set mode, after enter the setting mode, press
Clock ADJ. button (12) to change the mode cycle as follows:
Normal → Year → Month → Day → 12/24 H format → Real time Hour
→ Real time Min → Normal
Action (during data adjustment):
- Press << / Tune - button (8) to adjust data backward.
- Press >> / Tune + button (9) to adjust data forward.
- Keep depressed << or >> button for 2 seconds to enable auto
forward.
- Use Clock ADJ. (12) button to conrm each setting.
ALARM SETTING
Setting Alarm 1 and Alarm 2
Press the alarm set button (6/7) during normal mode to show
the alarm time. Afterwards keep depress the alarm set button
(6/7) over 2 seconds to enter the alarm set mode. After enter
the setting mode, press the alarm set button (6/7) to change the
mode cycle as follows :
Normal → ALARM 1 Hour → ALARM 1 Min → ALARM 1 weekday
Alarm → ALARM 1 wake beep → ALARM 1 wake radio → ALARM 1
wake radio volume →Normal.
Normal → ALARM 2 Hour → ALARM 2 Min → ALARM 2 weekday
Alarm → ALARM 2 wake beep → ALARM 2 wake radio → ALARM 2
wake radio volume →Normal.
Select alarm weekday mode as follows:
1-5: Monday to Friday
1-7: Whole week
6-7: Saturday & Sunday
1-1: One day of week
Action (during data adjustment):
- Press << / Tune - (8) button to adjust data backward.
- Press >> / Tune + (9) button to adjust data forward.
- Keep depressed << or >> button for 2 seconds to enable auto
forward.
- Use ALARM 1 / ALARM 2 set button to conrm each setting.
ALARM
Beep alarm or radio alarm will ring for 30 minutes if no key is pressed,
then it will stop automatically and wait for same alarm time on next
day.
Enable / disable the Alarm
Press and hold the “ALARM 1” (6) / “ALARM 2” (7) button to enable or
disable the alarm. Once the alarm is activated, the bell symbol will be
appeared on the display.
SNOOZE FUNCTION
When Alarm rings, press Snooze button (1) to suspend the alarm & to
activate the snooze function, Beep or Radio alarm will stop. 9 minutes
later the alarm will ring again. Press SNOOZE button (1) again, alarm
will be suspended again, another 9 minutes later the alarm will ring
again and so on until the next alarm rings.
Note: The interval time of the Snooze function is 9 minutes.
- If you want to disable the SNOOZE function and stop alarm
completely, press Radio ON/OFF button (13). If you don’t press any
button, the alarm will ring during 30 minutes & stop automatically.
- Icon of ALARM 1 and ALARM 2 will blink as long as Snooze
function is still operating. Once Snooze is turned off icon of ALARM
1 / ALARM 2 stop blinking and lights on the display.
SLEEP OPERATION
When you listen to the radio, press the SNOOZE/SLEEP/DIMMER
(1) button to enter into the sleep mode. You can adjust the sleep timer
from 90 minutes to 15 minutes by pressing repeatedly the SNOOZE/
SLEEP/DIMMER button (1). When sleep timer is selected, the unit will
automatically turn off once time is up.
.
DIMMER CONTROL
The dimmer button (1) allows you to set the brightness of the LED
display to high, medium and low 3 levels.
DISPLAY LIGHT AUTO ON/OFF FUNCTION
1. Press display light auto on-off button (10) for 3 seconds, the LED
display indicator will light on, the LED display will turn off after 15
seconds automatically.
Press any button to maintain the LED display for 15 seconds.
2. Press display light auto on-off (10) button for 3 seconds, the LED
display indicator will light off to cancel this function.
NAP timer function (count down timer)
During radio off mode, press MEM.SET / M+ / NAP button (12) to turn
on NAP mode, the NAP time will keep by 5 seconds, within 5 seconds
and press MEM.SET / M+ / NAP button (12) button can change the
duration from 90 min – 10 min.
The alarm buzzer will sound for 30 min and then shut off automatically.
To stop the alarm buzzer, press the ON/OFF button (13).
Press the MEM.SET / M+ / NAP button (12) has no effect during alarm
operation. Press ON/OFF button (13) to cancel NAP function.
DAYLIGHT SAVING TIME (DST) MODE
For countries with daylight saving time (DST) (one hour of difference
between summer time and winter time), this clock radio offers you DST
option to adjust summer time.
In standby mode press and hold for 2 seconds the >>/TUNE+/DST
button (9).
The clock advances by one hour. To exit DST mode, repeat the above
operation.
AUTO TOGGLING BETWEEN DISPLAY CONTENTS
In clock mode, press and hold DISPLAY button (11) for 3 seconds.
“ON” appears on the display. Then the display automatically shows
below contents in 5-10 second intervals.
Current time > Month, Day > Temperature > Humidity
To deactivate this function, press and hold DISPLAY button (11) for 3
seconds. “OFF” appears on the display, then the display switches back
to the clock mode.
Contents in 10-second intervals
Contents in 5-second intervals
Contents in 5-second intervals
Contents in 5-second intervals
RADIO MODE
Note: Ensure that the FM antenna is completely unrolled and
extended to have the best FM reception.
1. Press the Radio ON/OFF button (13) to turn the unit on.
2. Use the Tune - (8) or Tune + (9) button to select the desired radio
station. If you press and hold the Tune – (8) or Tune + (9) button for
one second, then release, the unit will automatically scan to the next
broadcasting station.
3. Press the ON/OFF button (13) to turn the radio OFF.
To set / recall the radio presets
1. Press the ON/OFF button (13) to turn the unit ON.
2. Use the Tune + or Tune - button to select the desired radio station.
3. Press and hold the memory / memory + button; “P01” will blink in the
display.
TIME
4. Use the Tune+ or Tune- button to select the desired preset station
(P01-P10)
5. Press the memory / memory + button again to set the preset.
6. Repeat steps 2 through 5 to set more presets.
7. The unit can preset 10 stations totally for FM.
8. When “P01-P10” is blinking, press the Tune+ or Tune- button to
select the preset number.
9. When recalling preset stations, press memory / memory + button to
select the preset number.
TO USE THE WEATHER FORECASTER
There is a built-in humidity sensor in your unit to make the weather
forecast. There are four types of weather display in your weather
station (please note that the weather graphics may look a little different
to those on your unit)
Remarks: for better use of your weather station, place your unit at
a location with open air circulation e.g. close by an open window.
Placing it at an air-conditioned environment will affect its accuracy.
After your weather station is powered up, it will take around 3 hour to
get stable. The weather icons on the display give a reference to the
next 12-24 hours weather conditions. It may not match with the current
weather condition outside.
Predictions accuracy: 70%; prediction of the considerable weather
changes (for example, from sunny weather to rain) is more accurate
then prediction of negligible weather changes (from partly cloudy to
cloudiness).
Weather station predicts possible weather, thus symbols could
not agree with current weather. Forecast: SUNNY for night means
cloudless sky.
Humidity sensor specication:
Operating temperature range : 10 ~ 50ºC
Operating humidity range : 30 ~ 95%
If temperature is below 10ºC or higher than 50ºC, The LED display will
show - - % for humidity and not show the weather forecast.
RESETTING
If the system does not respond or exhibits erratic or intermittent
operation, you may have experienced an electrostatic discharge (ESD)
or a power surge that triggered the internal microcontroller to shut
down automatically. If this occurs, simply disconnect the ac power
cord and remove the system backup battery, wait for at least 3 minutes
and then setup the unit again as if it is a brand new unit.
SPECIFICATIONS
Frequency range : FM 87.5 – 108 MHz
Battery backup : 3V (CR2032 Flat Lithium battery x 1) not included
Power supply : AC 230V 50Hz
Temperature range for Indoor : 0 to + 50°C or 32 to 122 °F
Humidity range for indoor : 30% to 95%
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S
www.denver-electrionics.com
Electric and electronic equipment contains materials, components and
substances that can be hazardous to your health and the environment,
if the waste material (discarded electric and electronic equipment) is
not handled correctly.
Electric and electronic equipment is marked with the crossed out
trash can symbol, seen below. This symbol signies that electric and
electronic equipment should not be disposed of with other household
waste, but should be disposed of separately.
All cities have established collection points, where electric and
electronic equipment can either be submitted free of charge at
recycling stations and other collection sites, or be collected from
the households. Additional information is available at the technical
department of your city.
Fill in the blank with the model number of this player, so you can nd it
again later.
Imported by:
DENVER ELECTRONICS A/S
Stavneagervej 22, DK-8250 EGAA, DENMARK
www.facebook.com/denverelectronics
Table des matières
Langues :
Autres manuels Denver Radio-réveil
Denver
Denver CR-323 Manuel utilisateur
Denver
Denver CRL-330 Manuel utilisateur
Denver
Denver CR-421 Manuel utilisateur
Denver
Denver CRLB-400 Manuel utilisateur
Denver
Denver CRL-330 Manuel utilisateur
Denver
Denver DAB-36 Manuel utilisateur
Denver
Denver IFM-90 Manuel utilisateur
Denver
Denver CRL-330 Manuel utilisateur
Denver
Denver CRL-330 Manuel utilisateur
Denver
Denver CRP-210 Manuel utilisateur
Denver
Denver CRP-514 Manuel utilisateur
Denver
Denver CRL-330 Manuel utilisateur
Denver
Denver CRQ-110 Manuel utilisateur
Denver
Denver TR-52 Fiche technique
Denver
Denver CR-414 Manuel utilisateur
Denver
Denver CRP-514 Manuel utilisateur
Denver
Denver CRP-912 Manuel utilisateur
Denver
Denver REC-34 Manuel utilisateur
Denver
Denver CRP-717 Manuel utilisateur
Denver
Denver CRP-717 Manuel utilisateur
