Demig DE-BT 1000 Manuel utilisateur

demig Prozessautomatisierung GmbH

Manual

Terminal DE-BT 1000

By demig Prozessautomatisierung GmbH

from version 12.1.1 (2017)

demig Prozessautomatisierung GmbH

Manual Terminal DE-BT 1000

This manual was produced using ComponentOne Doc-To-Help.™

demig Prozessautomatisierung GmbH

Manual Terminal DE-BT 1000 Content • i

Content

1. Cha ter: Introduction ....................................................................................... 1

1.1 Basic Information ............................................................................................. 1

1.1.1. General Handling .........................................................................................1

1.1.2. CE-Conformity .............................................................................................1

1.1.3. Installation Instructions ................................................................................1

1.1. . Structure of the Operating Instructions .........................................................2

1.1.5. Security Symbols .........................................................................................2

1.1.6. Disclaimer....................................................................................................2

1.2 Brief Explanation of the Industrial Terminal DE-BT 1000 ................................. 3

1.2.1. General Explanation ....................................................................................3

1.3 General Handling of the DE-BT 1000 .............................................................. 3

1.3.1. Commands ..................................................................................................

1.3.2. Status Line ..................................................................................................7

1.3.3. Menu ...........................................................................................................8

1.3. . Service Menu ..............................................................................................9

2. Cha ter: Service and Technical Data ............................................................ 11

2.1 General maintenance .................................................................................... 11

2.1.1. Cleaning and care of the keypad and of the screen .................................... 11

2.1.2. Direct Support............................................................................................ 11

2.2 Update of the System Software ..................................................................... 13

2.2.1. Necessary Material .................................................................................... 13

2.2.2. Starting the Update .................................................................................... 13

2.2.3. Update History ........................................................................................... 1

2.3 Technical Data .............................................................................................. 15

2.3.1. Control System Unit ................................................................................... 15

2.3.2. Installation and mounting ........................................................................... 15

2.3.3. PIN Assignments ....................................................................................... 16

2. Installation Dimensions and Measurements of Rack-Housing ........................ 17

2. .2. Connections .............................................................................................. 18

3. Cha ter: A endix .......................................................................................... 19

3.1 License Note ................................................................................................. 19

Index ......................................................................................................................... 21

demig Prozessautomatisierung GmbH

Manual Terminal DE-BT 1000 Cha ter: Introduction • 1

1. Cha ter: Introduction

1.1 Basic Information

1.1.1. General Handling

Please read the operating instruction carefully before installing or handling the

industrial terminal DE-BT 1000, in order to avoid dangerous situations and damages

due to operating errors. This operating manual is limited to the handling of the

DE-BT 1000 and does not include all different applications.

1.1.2. CE-Conformity

The industrial terminal DE-BT 1000 corresponds to the standards and guidelines

named in the conformity declaration. To make sure these are observed, please pay

attention to the following:

• It is the responsibility of the installing person to observe all the standards and

guidelines for the usage and installation of the industrial terminal DE-BT 1000.

• Make sure that only qualified staff installs the industrial terminal DE-BT 1000.

• Make sure that all the precautions stated in the chapter "Information for the

installation" are observed.

• Reparations of the industrial terminal DE-BT 1000 by the customer are not

allowed.

• By using the industrial terminal DE-BT 1000 for unintended purposes as well

violating the regulations mentioned above, demig Prozessautomatisierung GmbH

assumes no responsibility. The conformity declaration then loses its validity.

1.1.3. Installation Instructions

Please check the process control system immediately upon receipt. In case of any

damages, the device must not be installed. Pay attention to the terms of installation in

chapter service and technical data.

demig Prozessautomatisierung GmbH

2 • Cha ter: Introduction Manual Terminal DE-BT 1000

1.1.4. Structure of the O erating Instructions

All security advices in this operating manual are marked with this symbol:

Further information is shown in a frame with the headline information. Security

functions are marked with the following symbol:

1.1.5. Security Symbols

The following security symbols are shown on the terminal:

Attention! An incorrect connection of the device may lead to system

disturbances, - damages, quality losses as well as danger to persons

and environment. The connections not marked directly at the

controller are explained in the corresponding documentation

(Operating Instructions, Pin Assignment Cards).

Protective ground wire (min. 6mm² cross section!)

1.1.6. Disclaimer

Possible errors cannot be excluded. demig Prozessautomatisierung GmbH

assumes neither a legal res onsibility nor the liability for mis rints, wrong

information and/or omissions or the resultant damages. Suggestions for

im rovement and advice are always welcome.

W ar ni ng :

Notice:

demig Prozessautomatisierung GmbH

Manual Terminal DE-BT 1000 Cha ter: Introduction • 3

1.2 Brief Ex lanation of the Industrial

Terminal DE-BT 1000

1.2.1. General Ex lanation

The industrial terminal DE-BT 1000 is a display and input terminal. As it is only a

terminal, a further host system for the control is needed (e.g.: process supervisory

system prosys/2). The host system transmits the messages/commands via different

communication systems to the DE-BT 1000.

After receiving a message, the display is updated for the user. In case of an input mask

on the screen, the keypad can be used to enter the data which then will be requested

by the host system.

1.3 General Handling of the DE-BT 1000

The DE-BT 1000 has a main display, which is shown immediately after the start. This

is also the range for masks and texts. Furthermore, it has a status line in which different

information can be shown. From this main display, different instructions can be carried

out by key shortcuts. The instructions and the corresponding key shortcuts are

described in the menu point „Commands“.

Use the tab keys and to switch between the different input parts in a menu.

The entry can be selected with the arrow keys after marking a selection field. Buttons

can be confirmed by „ENTER“ and selections change the status with the space bar

„



“. Inputs in a text field are done by the keypad.

demig Prozessautomatisierung GmbH

4 • Cha ter: Introduction Manual Terminal DE-BT 1000

1.3.1. Commands

1.3.1.1. Delete Messages

Messages or errors in the status line can be blanked out by mouse click or by key

shortcut [SHIFT] + [F7] ausgeblendet werden.

1.3.1.2. Configuration Menu

By the shortcut [SHIFT] + [F8] the configuration menu of the DE-BT 1000 is reached.

First you have to answer the security request „Do you really want to open the DE-BT

1000 configuration?“ with „ es“. In case of „No“ as answer, the user returns to the main

display.

Different settings can be done in the configuration menu. The following list gives a

short overview of the setting possibilities. In case of a selection field, the possible

options are shown in the square brackets.

• GID (device ID) [0-9]

• UID (user ID) [0-9]

• Baud rate RS 85 [300, 600, 1200, 2 00, 800, 9600, 19200, 38 00]

• Parity RS 85 [o=Odd, e=Even, n=None]

• Stop bits RS 85 [1, 2]

• Baud rate RS232 [300, 600, 1200, 2 00, 800, 9600, 19200, 38 00]

• Parity RS232 [o=Odd, e=Even, n=None]

• Stop bits RS232 [1, 2]

• Active [RS232, RS485, NET]

• Port number [102 -65535]

• DHCP

• IP address

• Subnet mask

• Default gateway

The GID and UID are used for the device addressing. Furthermore, the interface

configuration can be determined. That includes the serial interfaces RS232 and

RS 85, as well as the IP configuration. Moreover, the interface, which should be used

for the communication with the host system, can be selected in the selection field

„Active“. For a communication via network (NET) the selected Port is used.

demig Prozessautomatisierung GmbH

Manual Terminal DE-BT 1000 Cha ter: Introduction • 5

1.3.1.3. Factory Settings

To set the terminal back to factory setting, use the shortcut [SHIFT] + [F1] in the

configuration menu. In case the security request is answered with „ es“ the DE-BT

1000 is set back to factory settings. The factory settings are as follows:

• GID = 1

• UID = 1

• Baud rate RS 85 = 9600

• Parity RS 85 = o

• Stop bits RS 85 = 2

• Baud rate RS232 = 9600

• Parity RS232 = o

• Stop bits RS232 = 2

• Active = RS 85

• Port number = 50000

• DHCP = Yes

• IP address = 0.0.0.0

• Subnet mask = 255.255.255.0

• Default gateway = 0.0.0.0

1.3.1.4. Information Dis lay

Information about the preset configuration can be displayed by [SHIFT] + [F2] in the

configuration menu in case, the request was confirmed with „ es“. Besides this

information, also the current network configuration is shown.

demig Prozessautomatisierung GmbH

6 • Cha ter: Introduction Manual Terminal DE-BT 1000

1.3.1.5. Keyboard Test

The keyboard test can be called by [SHIFT] + [F4] and the following confirming with

„ es”. In the now appearing window the keys to be pressed on the softkeyboard are

highlighted in color. After the successful pressing of a key, it will be deleted in the

display. The keyboard test is closed automatically when no further key is shown.

highlighted key

1.3.1.6. Exit terminal mode

To exit the terminal mode and go to the menu (see chapter 1.3.3) use the key

combination [SHIFT] + [F8] in the configuration menu. You only reach the service

menu after confirming the following request with „ es“.

1.3.1.7. U date

The update program is started with [SHIFT] + [F9] from the configuration menu and by

confirming the appearing request with „ es“. After that the update can be installed by

the File Transfer Manager (FTM).

Table des matières

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur

demig DE-BT 1000 Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques