Dell E03T Manuel utilisateur

Dell SC7020 and SC7020F Storage

Systems

Getting Started Guide

Regulatory Model: E03T

Regulatory Type: E03T001

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make

better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or

loss of data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be

trademarks of their respective owners.

2017–10

Rev. A01

Setting Up the Storage System

Consider the following best practices when setting up an SC7020 series storage

system.

• Dell recommends that you use a dedicated SAN network for data transmission

when using a Fibre Channel or iSCSI storage system.

• Always congure redundant data paths to provide alternate paths to and from the

host server should one of the data paths become disabled.

• Before connecting any cables between the storage system and host server or

expansion enclosure, physically label each port and connector.

• Always follow proper power-up and power-down procedures when cycling power

across the network. Verify that critical network components are on separate

power circuits.

NOTE: This product is intended for restricted access locations, such as a

dedicated equipment room or equipment closet.

WARNING: If installed in a closed or multi-unit rack assembly, the operating

ambient temperature of the rack environment may be greater than room

ambient temperature. Therefore, consideration should be given to installing

the equipment in an environment compatible with the maximum ambient

temperature (Tma) specied by the manufacturer.

Safety Warnings

Two person lift required

A fully congured SC7020 series storage system

weighs approximately 45 kg (100 lb). Use appropriate

lifting methods when installing the storage system.

Laser Radiation for Fibre Channel Storage Systems

CAUTION: Class I laser radiation when open, avoid exposure

to beam.

WARNING: Laser radiation, avoid direct exposure to beam.

The unit is certied in the U.S. to conform to the requirements of DHHS 21 CFR,

chapter 1 Subchapter J for Class I (1) laser products, and elsewhere is certied as a

Class I laser product conforming to the requirements of IEC 60825-1:2007.

Class I laser products are not considered to be hazardous. The laser system and unit

are designed so there is never any human access to laser radiation above a Class I

level during normal operation, user maintenance or prescribed service condition.

Locating Your Service Tag

Your storage system is identied by a unique service tag and Express Service Code.

The service tag and Express Service Code are found on the front of the system by

pulling out the information tag. Alternatively, the information might be on a sticker on

the back of the storage system chassis. This information is used by Dell to route

support calls to the appropriate personnel.

NOTE: The Quick Resource Locator (QRL) code on the information tag is

unique to your system. Scan the QRL to get immediate access to your

system information using your smart phone or tablet.

Other Information You May Need

To install the storage system, you may need the following additional information:

•Dell SC7020 and SC7020F Storage Systems Owner’s Manual

Provides information about an SC7020 series storage system, such as hardware

features, replacing hardware components, and technical specications.

•Dell Storage Manager Administrator’s Guide

Provides instructions for using the Data Collector Manager and the Dell Storage

Manager Client.

Installation and Conguration

Before you begin installation, make sure that the site where you plan to install the

storage system has standard power from an independent source or a rack power

distribution unit with a UPS.

In addition, verify that there is a 3U space in the lower 20U of the rack to install the

storage system. If you plan to install the storage system above the lower 20U of a

rack, a customer-provided mechanical lift must be used to avoid injury.

Unpacking Storage Center Equipment

Unpack the storage system and identify the items in your shipment.

Figure 1. SC7020 Series Storage System Components

1. Documentation 2. Storage system

3. Rack rails 4. USB cables (2)

5. Power cables (2) 6. Front bezel

Install the Storage System in a Rack

Install the storage system and other Storage Center system components in a rack.

About this task

Mount the storage system and expansion enclosures in a manner that allows for

expansion in the rack and prevents the rack from becoming top‐heavy.

The SC7020 series storage system ships with a ReadyRails II kit. The rails come in two

dierent styles: tool-less and tooled. Follow the detailed installation instructions

located in the rail kit box for your particular style of rails.

NOTE: Dell recommends using two people to install the rails, one at the

front of the rack and one at the back.

Steps

1. Position the left and right rail end pieces labeled FRONT facing inward.

2. Align each end piece with the top and bottom holes of the appropriate U space.

Figure 2. Attach the Rails to the Rack

3. Engage the back end of the rail until it fully seats and the latch locks into place.

4. Engage the front end of the rail until it fully seats and the latch locks into place.

5. Align the system with the rails and slide the storage system into the rack.

Figure 3. Slide the Storage System Onto the Rails

6. Lift the latches on each side of the front panel and tighten the screws to the

rack.

Figure 4. Tighten the Screws

If the Storage Center system includes expansion enclosures, mount the expansion

enclosures in the rack. See the instructions included with the expansion enclosure for

detailed steps.

Install the Front Bezel

Install the bezel on the front of the storage system.

1. Hook the right end of the bezel onto the storage system.

Figure 5. Front Bezel

2. Insert the left end of the bezel into the securing slot until the release latch snaps

into place.

3. Secure the bezel with the keylock.

Connect the Power Cables

Connect power cables to the storage system.

1. Make sure that the power switches are in the OFF position before connecting

the power cables.

2. Connect the power cables securely to both power supply/cooling fan modules in

the storage system chassis.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dell Stockage

Dell

Dell PowerVault 51F Manuel utilisateur

Dell

Dell Express Flash NVMe PCIe SSD U.2 Manuel utilisateur

Dell

Dell EqualLogic FS7610 Instructions de montage

Dell

Dell PowerVault TL2000 Manuel utilisateur

Dell

Dell PowerVault MD3200 Series Instructions d'installation

Dell

Dell PowerVault LTO 8 Manuel utilisateur

Dell

Dell PowerVault 110T DLT4000 Manuel utilisateur

Dell

Dell PowerVault 220S Manuel utilisateur

Dell

Dell PowerVault NX300 Manuel utilisateur

Dell

Dell PowerVault MD3800f series Guide de référence rapide

Dell

Dell PowerVault MD3200i Series Manuel utilisateur

Dell

Dell PowerVault 220S Manuel utilisateur

Dell

Dell PowerVault MD3000i Manuel utilisateur

Dell

Dell EqualLogic PS4000 Manuel utilisateur

Dell

Dell PowerVault 200S Instructions d'installation et d'entretien

Dell

Dell PowerVault 220S Manuel utilisateur

Dell

Dell PowerVault LTO4-120 Manuel utilisateur

Dell

Dell PowerVault NX200 Manuel utilisateur

Dell

Dell PowerVault 725N Manuel d'utilisation et d'entretien

Dell

Dell EMS01 Manuel utilisateur

Dell

Dell PowerVault 2385P Manuel utilisateur

Dell

Dell PowerVault LTO Manuel utilisateur

Dell

Dell EqualLogic FS7600 Instructions de montage

Dell

Dell PowerProtect DD6900 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur