Dell PowerEdge C6220 II Manuel utilisateur
Dell PowerEdge
C6220 II
Getting Started
With Your System
Začínáme se systémem
Mise en route du système
Handbuch zum Einstieg
mit dem System
Τα πρώτα βήματα με το σύστημά σας
Instrukcja uruchomienia systemu
Руководство по началу
работы с сервером
Pasos iniciales para su sistema
Sisteminizi Kullanmaya Başlarken
Dell PowerEdge
C6220 II
Getting Started
With Your System
Notes, Cautions, and Warnings
NOTE:
A NOTE indicates important information that helps you make better use of
your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of
data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
______________
Information in this document is subject to change without notice.
© 2013 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission
of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of
Dell Inc. Intel® and Intel® Xeon® are registered trademarks of Intel Corporation in the
U.S. and other countries. Red Hat Enterprise Linux® and Enterprise Linux® are
registered trademarks of Red Hat, Inc. in the United States and/or other countries.
Novell® is a registered trademark and SUSE™ is a trademark of Novell Inc. in the United
States and other countries. Citrix® and XenServer® are either registered trademarks or
trademarks of Citrix Systems, Inc. in the United States and/or other countries. VMware®
is a registered trademarks or trademarks of VMWare, Inc. in the United States or other
countries.
Other trademarks and trade names may be used in this publication to refer to either the
entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
Regulatory Model B08S
May 2013 P/N MYF2N Rev. A00
Getting Started With Your System | 3
CAUTION: Restricted Access Location
This server is intended for installation only in restricted access locations as
defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions apply:
•
Access can only be gained by service persons or by users
who have been
instructed about the reasons for the restrictions applied to the location and
about any precautions that shall be taken.
•
Access is through the use of a tool or lock and key, or other means of
security, and is controlled by the authority responsible for the location.
Installation and Configuration
WARNING: Before performing the following procedure, review and follow the
safety instructions that came with the system.
Installing the Tool-Less Rail Solution
WARNING: Whenever you need to lift the system, get others to assist you.
To avoid injury, do not attempt to lift the system by yourself.
WARNING: The system is not fixed to the rack or mounted on the rails. To
avoid personal injury or damage to the system, you must adequately
support the system during installation and removal.
WARNING: To avoid a potential electrical shock hazard, a third wire safety
grounding conductor is necessary for the rack installation. The rack
equipment must provide sufficient airflow to the system to maintain proper
cooling.
CAUTION: When installing rails in a square-hole rack it is important to
ensure that the square peg slides through the square holes.
Getting Started With Your System | 4
1
Push on the latch release buttons on the midpoints of the end piece to
open the rail latches. See Figure 1.
2
Align the end pieces of the rails on the vertical rack flanges to seat the
pegs in the bottom hole of the first U and the top hole of the second
U.
NOTE:
The rails can be used in both square-hole (item 1 in the following figure)
and round-hole racks (item 2 in the following figure).
Figure 1. Pushing the Latch Release Buttons
NOTE:
To remove the rails, push on the latch release button on the midpoints
of the end piece and unseat each rail.
Getting Started With Your System | 6
4
On each vertical rack flange on the back, put two screw bases into the
two square holes right above the rail. See Figure 3.
5
Install the chassis stabilizer shipping brackets (optional) on the back
rack flanges.
6
Install and tighten the screws.
NOTE:
To transport systems already installed in the rack, ensure that the two
chassis stabilizer shipping brackets (optional) are in place.
Figure 3. Installing the Chassis Stabilizer Shipping Brackets
Getting Started With Your System | 8
Optional—Connecting the Keyboard, Mouse, and Monitor
Figure 5. Optional—Connecting the Keyboard, Mouse and Monitor
Connect the keyboard, mouse, and monitor (optional).
The connectors on the back of your system have icons indicating which cable to
plug into each connector. Be sure to tighten the screws (if any) on the monitor’s
cable connector.
Autres manuels pour PowerEdge C6220 II
5
Table des matières
Langues :
Autres manuels Dell Serveur
Dell
Dell PowerEdge 2400 Instructions générales
Dell
Dell 100 Series Manuel
Dell
Dell EMC PowerEdge R6525 Manuel
Dell
Dell PowerEdge R415 Manuel utilisateur
Dell
Dell PowerEdge 7150 Manuel utilisateur
Dell
Dell PowerEdge R620 Guide de démarrage rapide
Dell
Dell PowerEdge R300 Manuel utilisateur
Dell
Dell EMC PowerEdge R740 Manuel
Dell
Dell PowerEdge PDU Managed LED Manuel utilisateur
Dell
Dell PowerEdge T630 Manuel utilisateur
Dell
Dell PowerEdge 4600 Manuel utilisateur
Dell
Dell POWEREDGE M905 Manuel utilisateur
Dell
Dell PowerEdge 2500 Manuel utilisateur
Dell
Dell PowerEdge 6600 Manuel utilisateur
Dell
Dell PowerEdge M630 Manuel utilisateur
Dell
Dell Wyse ThinOS T10 Manuel utilisateur
Dell
Dell PowerEdge R410 Manuel utilisateur
Dell
Dell PowerVault MD3600i Series Manuel utilisateur
Dell
Dell Force10 S2410-01-10GE-24P Manuel d'installation
Dell
Dell Wyse ThinOS T10 Manuel utilisateur
