Dell Networking C9010 Manuel utilisateur

Dell Networking C9010

Installation Guide

Regulatory Model: C9010

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2015 - 10

Rev. A00

About This Guide

This document provides information about how to install a C9010 switch with the base configuration in a

rack. For complete information about C9010 installation and configuration, refer to these documents:

Table 1. C9010 Documentation

Information Documentation

Hardware installation, power-up, and initial

software configuration instructions

Dell Networking C9010 Getting Started Guide

Software configuration Dell Networking Configuration Guide for the

C9000 Series

Command-line interface Dell Networking Command-Line Reference Guide

for the C9000 Series

Latest updates Dell Networking C9010 and C1048P Release Notes

About This Guide 3

C9010 Hardware Description

The C9010 switch is part of Dell Networking's next-generation LAN solution, providing a scalable switch

that offers a path to higher density 10GbE and 40GbE capability. You can deploy the C9010 switch as an

access or aggregation/core switch for installations in which a modular switch is preferred. For larger port

requirements, you can also connect C1048P port extenders (PEs) as access devices.

The C9010 switch supports up to two hundred and forty-eight 1GbE, two hundred and forty-eight

10GbE, or sixty 40GbE ports with a combination of port speeds and media types, such as copper, fiber,

and direct attach copper (DAC). It is an 8U chassis (18”/45.72 cm depth) that fits into a standard 19”/48.26

cm rack or cabinet. The C9010 chassis supports the following components:

• Two full-width route processor modules (RPMs) with four 1/10GbE SFP+ uplinks per module

• Ten half-width Ethernet line cards of the following types:

– 6-Port 40 Gigabit Ethernet QSFP+

– 24-Port 1/10 Gigabit Ethernet SFP+

– 24-Port 1/10 Gigabit Ethernet Base-T RJ-45

• Three hot-swappable fan modules with side-to-side airflow (draws air through ventilation holes on

the right side of the chassis and expels air through ventilation holes on the left side)

• Four 1450/2900 watt AC power supply units (PSUs)

The slot numbers of all installed components are shown in the following figure.

4C9010 Hardware Description

Figure 1. C9010 Chassis — Installed Components with Slot Numbers

Unpacking the Switch

The switch and its accessories ship in a single container. Before unpacking the switch, inspect the

container and immediately report any evidence of damage. Verify that you have received your ordered

items. If any item is missing or damaged, contact your Dell Networking representative or reseller for

assistance.

CAUTION: Always wear an electrostatic discharge (ESD)-preventive wrist or heel ground strap

when handling the switch and its components. Ground yourself by using an antistatic wrist strap

or other device and connect it to the ESD grounding jack on the chassis. As with all electrical

devices of this type, take all necessary safety precautions to prevent injury when installing this

system.

CAUTION: Use an equipment lift or pallet jack to lift the shipping container with the chassis.

Lifting the system by its shelves causes damage to the chassis.

Unpack the C9010 by carefully removing the device from the container and place it on a secure and

clean surface.

C9010 Hardware Description 5

The base C9010 configuration package consists of:

• One C9010 chassis

• One full-width C9000 Series RPM

–C9000-RPM-2.56T displays in SW output.

–07KPC3 or 0N90RW is on the HW label.

• Three C9000 Series fan modules

–C9000-FAN displays in SW output.

–0C94MF is on the HW label.

• One AC PSU (110-230V switching)

–C9000-PWR-AC displays in SW output.

–D3000E-S0 is on the HW label.

• AC power cord (IEC 60320 C19 cable)

• One DB-9 to RJ-45 serial console cable

• One rack bar with four screws and washers

• Eight cage nuts (four for the rack bar; four for the chassis thumb screws)

• Blank panels: one RPM, three PSU, and nine half-width line card blanks

• Two cable management brackets

•C9010 Getting Started Guide

•Safety and Regulatory Information

•Warranty and Support Information

•Software License Agreement

In addition, you can order the following items:

• Up to three additional PSUs for redundancy or additional power

• Half-width line cards:

– 6-Port 40 Gigabit Ethernet QSFP+ (C9000LC0640 displays in SW output.)

– 24-Port 1/10 Gigabit Ethernet SFP+ (C9000LC2410G displays in SW output.)

– 24-Port 1/10 Gigabit Ethernet Base-T RJ-45 (C9000LC2410T displays in SW output.)

• SFP+ optics

• QSFP+ optics

• SFP+ direct attach copper (DAC) cables

• QSFP+ DAC cables

• DB-9 adapter

• Dell ReadyRails™ kit (#1 and #2 Phillips and flat-tipped screwdrivers required) with four cage nuts

• Rack mount tray

• C1048P port extenders for use with the C9010

Before You Start: Site Preparation

Before installing the C9010 switch, make sure that your installation site meets these requirements:

•Clearance: Ensure there is adequate space in front of the switch so you can read the light-emitting

diodes (LEDs) and adequate space around and behind the chassis for cabling, power connections,

6C9010 Hardware Description

airflow, and ventilation. Make sure that the AC power cord can reach the power connector on the

front panel of a power supply unit from the power outlet.

•Airflow: On the C9010, airflow is from the right to the left side as you face the switch. Hot air is

expelled from the left side. Ensure that airflow around the switch and through the side vents is

unobstructed and that hot exhaust is not used as air intake on the right side.

•Temperature: The ambient temperature around the operating switch should not exceed 113°F (45°C).

If the switch is in a closed or multi-rack assembly, the temperature might be higher than normal room

temperature.

•Cabling: Route the cabling to avoid sources of electrical noise, such as radio transmitters, broadcast

amplifiers, power lines, and fluorescent lighting fixtures. Make sure that the cabling is safely away from

other devices that might damage the cables. If needed, allow 1 RU between devices to provide room

for cabling.

•Altitude: Altitude at the installation site is below 10,000 feet (3048 m).

•Humidity: The relative humidity around the operating switch is between 5% and 95% (non-

condensing) with 91°F (33°C) maximum dew point.

•Dust: Install the switch in an environment as free as possible from dust and foreign conductive

material (such as metal flakes from construction activities). Cooling mechanisms, such as fans in the

switch, can draw dust and other particles inside the chassis, which can result in system malfunction.

C9010 Hardware Description 7

Installing the Hardware

To install the C9010 chassis and power up the switch:

1. Install the C9010 chassis in a 2- or 4-post rack using the rack bar and mounting brackets shipped

with the chassis, or use an optional rack mount tray or Dell ReadyRails kit.

2. Secure the chassis ground.

3. Install the fan modules.

4. Install RPMs and line cards.

5. Install the power supplies and power cables.

6. Install the cable management system.

7. Install the QSFP+ and SFP+ optics.

8. Connect the power and power up the system.

WARNING: Due to the weight of a fully populated C9010 chassis, remove each component before

you install or remove the chassis.

After you install the switch in a rack and power it up, perform the initial software configuration and

connect the switch to a network as described in the Dell Networking C9010 Getting Started Guide.

Installing the Chassis in a Two-Post Threaded-Hole Rack

You can install the chassis in a 2-post threaded-hole rack by following the tooled procedure in this

section. A flat-head and a Philips screwdriver are necessary.

WARNING: Use two people, an equipment lift, or pallet jack when lifting or moving the chassis.

Install the chassis into the rack before inserting the chassis components. Lift the C9010 chassis

only from the bottom. Lifting by the chassis shelves or power supply openings might damage the

chassis.

WARNING: To prevent bodily injury when mounting or servicing this unit in a rack, take special

precautions to ensure that the system remains stable. The following guidelines are provided to

ensure your safety:

• If your chassis is the only unit in the rack, mount it at the bottom of the rack.

• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with

the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing

the unit in the rack.

• If the chassis is shipped with blanks, remove the blanks from each RPM, line card, fan module

and PSU slot before lifting the chassis.

1. (Optional) The C9010 chassis is designed to fit into a rack enclosure with the front door closed. If

you plan to use cable management brackets (see Installing the Cable Management System ) and

8Installing the Hardware

close the front door, re-position and fasten the front rack posts 6.5 inches (165 mm) back towards

the rear of the rack to leave space for the brackets.

2. Determine the height at which you want to mount the chassis in the equipment rack.

3. Install the rack bar on the front posts just below the desired height of the bottom of the chassis. The

rack bar requires 1 RU below the chassis.

Use the rack bar as a guide to mount the chassis. It is not required to support the weight of the

chassis; you can remove it when the chassis is securely mounted in the rack.

Hold the rack bar (item 1 in Figure 2) so that the smooth side faces outward and the arrows point

upward. Attach the bar to the front-rack posts using the mounting screws and washers provided with

the rack bar (items 2 and 3 in Figure 2).

NOTE: The installation procedure in this section describes how to install the C9010 in a 2-post

rack using the rack bar provided in the base configuration package. For information about how

to use Dell ReadyRails or a rack mount tray to install the C9010, follow the instructions in

Installing Dell ReadyRails or Installing a Rack Mount Tray. Then continue with Step 4.

Figure 2. Installing a Rack Bar in a 2-Post Rack

Installing the Hardware 9

4. Using a flat-head screwdriver, remove the bracket screws (item 1 in Figure 3) and unscrew the thumb

screws to remove the bracket (item 2 in Figure 3) attached to each chassis flange.

Figure 3. Removing Brackets from the Chassis

10 Installing the Hardware

Autres manuels pour Networking C9010

Table des matières

Autres manuels Dell Routeur réseau

Dell

Dell PowerConnect 3048 Manuel utilisateur

Dell

Dell PowerConnect J-8208 Mode d’emploi

Dell

Dell Z9000 Manuel utilisateur

Dell

Dell Networking S4810 Manuel utilisateur

Dell

Dell C9000 series Manuel utilisateur

Dell

Dell PowerConnect M8024-k Manuel utilisateur

Dell

Dell PowerConnect J-8216 Manuel utilisateur

Dell

Dell PowerConnect 3248 Manuel utilisateur

Dell

Dell Networking X4012 Manuel utilisateur

Dell

Dell POWERCONNECT J SERIES Manuel utilisateur

Dell

Dell PowerConnect M8024 Mode d’emploi

Dell

Dell PowerConnect J-EX4500 Instructions d'installation

Dell

Dell Networking S5000 Manuel utilisateur

Dell

Dell PowerConnect 5500 Series Manuel utilisateur

Dell

Dell PowerConnect B-MLXe Series Manuel utilisateur

Dell

Dell E1200i ExaScale Manuel utilisateur

Dell

Dell Networking S5000 Manuel utilisateur

Dell

Dell PowerConnect M8024 Manuel utilisateur

Dell

Dell PowerConnect J-8208 Manuel utilisateur

Dell

Dell PowerConnect 7000 Series Manuel utilisateur

Dell

Dell Precision 5750 Guide de l'utilisateur

Dell

Dell S3100 Series Manuel utilisateur

Dell

Dell S6000-ON Manuel de la liste des pièces

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité