Dell VEP1400 Series Manuel utilisateur

VEP1400

Setup Guide

, E42W

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

may be trademarks of their respective owners.

2018 - 08

Rev. A00

Contents

1 About this guide............................................................................................................................................. 4

Related documents............................................................................................................................................................ 4

Information symbols...........................................................................................................................................................4

2 Site preparations........................................................................................................................................... 5

Site selection...................................................................................................................................................................... 5

Chassis mounting...............................................................................................................................................................5

System ground................................................................................................................................................................... 5

Fans and airow................................................................................................................................................................. 5

Power.................................................................................................................................................................................. 6

Storing components.......................................................................................................................................................... 6

3 VEP1400 installation...................................................................................................................................... 7

Unpack.................................................................................................................................................................................7

Platform power-up............................................................................................................................................................. 7

Power up sequence..................................................................................................................................................... 8

4 Specications................................................................................................................................................9

Chassis physical design..................................................................................................................................................... 9

5 Support.........................................................................................................................................................11

Contents 3

About this guide

This guide provides site preparation recommendations, step-by-step procedures for rack mounting and desk mounting, inserting modules,

and connecting to a power source.

CAUTION: To avoid electrostatic discharge (ESD) damage, wear grounding wrist straps when handling this equipment.

WARNING: Only trained and qualied personnel can install this equipment. Read this guide before you install and power up this

equipment. This equipment contains two power cords. Disconnect both power cords before servicing.

WARNING: This equipment contains optical transceivers, which comply with the limits of Class 1 laser radiation.

Figure 1. Class 1 laser product tag

WARNING: When no cable is connected, visible and invisible laser radiation may be emitted from the aperture of the optical

transceiver ports. Avoid exposure to laser radiation, and do not stare into open apertures.

Topics:

• Related documents

• Information symbols

Related documents

For more information about the Virtual Edge Platform 1400 (VEP1400), see the following documents:

•VEP1400 Installation Guide

•VEP1400 Release Notes

NOTE: For the most recent documentation, see the support site: www.dell.com/support.

Information symbols

This book uses the following information symbols:

NOTE: The Note icon signals important operational information.

CAUTION: The Caution icon signals information about situations that could result in equipment damage or loss of data.

WARNING: The Warning icon signals information about hardware handling that could result in injury.

WARNING: The ESD Warning icon requires that you take electrostatic precautions when handling the device.

4 About this guide

Site preparations

VEP1400 is universal customer premise equipment (uCPE). To connect the service provider edge or small to medium branch locations to

the cloud, use VEP1400 to host virtual network functions.

For more information on VEP1400 specications, see Chassis physical design.

NOTE: Install the platform into a rack or cabinet before installing any optional components.

Topics:

• Site selection

• Chassis mounting

• System ground

• Fans and airow

• Power

• Storing components

Site selection

Ensure that the area where you install your platform meets the following safety requirements:

• Near an adequate power source

• Environmental—platform location—continuous temperature range is from 0°C to 45°C (32–113°F)

• Operating humidity:

– 5% to 85% (RH), noncondensing continuously

– 5% to 90% (RH), noncondensing Short term (< 1% of operational hour per year)

• In a dry, clean, well-ventilated, and temperature-controlled room, away from heat sources such as hot air vents or direct sunlight

• Away from sources of severe electromagnetic noise

For more information about platform storage and environmental temperatures, see Specications.

Chassis mounting

The VEP1400 supports desktop placement (rubber feet), wall mount (using brackets) and rack-mount using a dual-unit tray.

System ground

Dell recommends grounding your system. Use VEP4600 in a CBN.

Fans and airow

Fan installation is done as part of the factory install based on stock keeping unit (SKU) type. VEP 4600 supports an AC normal fan unit

with fan airow from the I/O to the PSU.

Site preparations 5

For proper ventilation, position the platform in an equipment rack or cabinet with a minimum of 5 inches (12.7 cm) of clearance around the

exhaust vents. The fan speed varies based on internal temperature monitoring. The platform never intentionally turns o the fans.

Power

Connect the platform to the applicable power source using the appropriate power cable. The VEP1400 ships with one external AC/DC

power supply and one AC power cable.

When installing AC platforms, follow the requirements of the National Electrical Code ANSI/NFPA 70, where applicable.

ATTENTION REVIEWERS:

Verify that this comment is correct.

The platform is powered-up when the power cable is connected between the platform and the power source.

CAUTION: Always disconnect the power cable before you service the power supply slots. The platform has multiple power

cables. Before servicing, ensure that all power cables are disconnected.

CAUTION: Use the power supply cable as the main disconnect device. Ensure that the socket-outlet is located/installed near the

equipment and is easily accessible.

Storing components

If you do not install the VEP1400 and components immediately, properly store the platform and all optional components following these

guidelines:

• Storage location temperature must remain constant. The storage range is from -40°C to 70°C (-40°F to 158°F).

• Store on a dry surface or oor, away from direct sunlight, heat, and air conditioning ducts.

• Store in a dust-free environment.

NOTE: ESD damage can occur when components are mishandled. Always wear an ESD-preventive wrist or heel ground strap

when handling the platform and its accessories. After you remove the original packaging, place the VEP1400 and its components

on an antistatic surface.

6 Site preparations

VEP1400 installation

To install VEP1400, complete the installation procedures in the order presented in this section.

Always handle the platform and its components with care. Avoid dropping the platform or any eld replaceable units (FRUs).

NOTE: ESD damage can occur if components are mishandled. Always wear an ESD-preventive wrist or heel ground strap when

handling the platform and its components. As with all electrical devices of this type, take all the necessary safety precautions to

prevent injury when installing this platform.

Topics:

• Unpack

• Platform power-up

Unpack

NOTE: Before unpacking the platform, inspect the container and immediately report any evidence of damage.

When unpacking VEP1400, ensure that the following items are included:

• One VEP1400

• Mini-USB console cable

• One AC/DC power supply and AC power cable

• Wall mount hardware

•VEP1400 Setup Guide

•Safety and Regulatory Information

•Warranty and Support Information

1 Place the container on a clean, at surface.

2 Open the container.

3 Carefully remove the unit from the container and place it on a secure and clean surface.

4 Remove all packing material.

5 Inspect the product and accessories for damage.

Platform power-up

Supply power to the VEP1400 after you mount it in a rack or desktop.

Reinspect your platform before power-up. Verify the following:

• The ambient temperature around the unit, which may be higher than the room temperature, be within the limits that are specied for

the VEP1400, see Specications.

• There is sucient airow around the unit.

• The input circuits are correctly sized for the loads and that you use sucient overcurrent protection devices.

• All protective covers are in place.

CAUTION: If a fan module is not installed, do not power up the platform.

VEP1400 installation 7

NOTE: A US AC power cable is included for powering up an AC power supply. You must order all other power cables separately.

NOTE: If the components are mishandled, ESD damage can occur. Always wear an ESD-preventive wrist or heel ground strap

when handling the platform and its components.

Power up sequence

For congurations that include a fan module, the fans immediately come on at high speed when the platform powers up. The fan speed

slows as the platform continues to boot up.

8 VEP1400 installation

Specications

This section lists the VEP4600 specications.

CAUTION: Operate the product at an ambient temperature not higher than 0°C to 45°C (32°F to 113°F).

CAUTION: Lithium Battery Caution: There is a danger of explosion if the battery is incorrectly replaced. Replace only with same

or equivalent type of battery. Dispose of the batteries according to the manufacturer's instructions.

NOTE: For RoHS information, see Restricted Material Compliance.

Chassis physical design

Table 1. Chassis physical design

Parameter Specications

Height 2.0 inches (50.8 mm)

Width 8.1 inches (205.74 mm)

Depth 7.9 inches (200.66 mm)

Chassis weight with factory-installed components

ATTENTION REVIEWERS:

Need verication on the chassis weight as it is not included in the

Source book yet.

• TBD (no fan)

• TBD (1 fan)

• TBD (2 fans)

Table 2. Environmental parameters

Parameter Specications

Operating temperature 0–40°C (32°F–104°F) continuously

Operating humidity • 5% to 85% (RH), noncondensing continuously

• 5% to 90% (RH), noncondensing short-term (< 1% of

operational hour per year)

Storage temperature –40° to 70°C (–40° to 158°F)

Storage humidity 5% to 90% (RH), noncondensing

Maximum thermal output

ATTENTION REVIEWERS:

Need verication on the max thermal output as it is not included in

the Source book yet.

TBD

Maximum operational altitude No performance degradation to 5,000 ft (1,524 meters)

Maximum nonoperational altitude 35,000 ft (10,668 meters)

Specications 9

16,404

5,000

Table 3. AC power requirements

Parameter Specications

Power supply 100–240 VAC 50/60 Hz

Maximum current draw per system - AC • 100 VAC: 2.0A

• 240 VAC: 1.0A

Maximum power consumption Typical:

• 200 W (8-core, POE+)

• 70 W (16 core)

• 60 W (8 core)

• 27 W (4 core)

• 25 W (2 core)

Maximum:

• 260 W (8-core, POE+)

• 110 W (16 core)

• 94 W (8 core)

• 55 W (4 core)

• 50 W (2 core)

Typical power consumption

ATTENTION REVIEWERS:

Need verication on the total power consumption as it is not

included in the Source book yet.

TBD

NOTE: For the most current AC power requirements and power consumption specications, see the Installation Guide at

www.Dell.com/support.

10 Specications

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dell Matériel réseau

Dell

Dell E665 Manuel

Dell

Dell DD6300 Manuel utilisateur

Dell

Dell 210-APGV Manuel utilisateur

Dell

Dell EMC NX3240 Instructions d'utilisation

Dell

Dell P570 Manuel utilisateur

Dell

Dell S4048T-ON Manuel utilisateur

Dell

Dell SonicWALL NSA E8510 Manuel utilisateur

Dell

Dell VEP4600 Manuel utilisateur

Dell

Dell EMC NX3240 Instructions d'utilisation

Dell

Dell VEP4600 Guide de l'utilisateur

Dell

Dell SonicWALL NSA 5600 Manuel utilisateur

Dell

Dell EMC XC640 Series Manuel

Dell

Dell PowerProtect DM5500 Manuel utilisateur

Dell

Dell EMC NX430 System Manuel utilisateur

Dell

Dell PowerVault RD1000 Manuel utilisateur

Dell

Dell Z9000 Mode d’emploi

Dell

Dell SonicWALL SuperMassive 9600 Manuel utilisateur

Dell

Dell Safeguard 5242LR Manuel utilisateur

Dell

Dell PowerVault TL4000 Manuel utilisateur

Dell

Dell OptiPlex Small Form Factor 7010 Manuel utilisateur

Dell

Dell Broadcom NetXtreme Family of Adapters Manuel utilisateur

Dell

Dell NX430 Manuel utilisateur

Dell

Dell AX150 Guide de référence

Dell

Dell PowerVault 124T Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur