Dell S2719DM Manuel utilisateur
Take out the whole packed monitor and then remove the EPE bags which packed monitor and stand base, and then put the monitor face down on the table with protective cushion.S3 Open the pizza carton with a proper tool, then put down the pizza carton, and open the carton. 1. Disassembly Procedures:S1 Lift up the stand , then use a Philips-head screwdriver to remove 2pcs screws for unlocking the whole unit including stand and base, then remove the stand and base. Use a Philips-head screwdriver to remove 2pcs screws for release the hinge cover.(No.1~2 screw size=M3x11, Torque=7.5±0.5kgfxcm; No.3~4 screw size=M2x0.4x3.2, Torque=2~3kgfxcm)S4 Take out the QSG from the catron, and then take out the Paper-Top with other accessories including user’s manual, HDMI cable, power cable, power adapter and other packing materials from the carton.(Note: It depends on whether users returning the accessories)S2 Use a proper tool insert the gap of the rear cover top side (marked 1) as the following picture to release the rear cover, then wedge your fingers between the rear cover and the panel to release the rear cover, then use one hand to press the panel module, the other hand to pull up carefully the rear cover in order of arrow preference 1~3 for unlocking mechanisms of rear cover, and then remove the rear cover carefully.S51
DELL S2719DM12QSG132343
S72Tear off 2pcs double-faced tapes on the left and right side of the middle bezel, then tear off 2pcs aluminum foil to release the panel lamp cable and LVDS connector. S6DELL S2719DMUse a Philips-head screwdriver to remove 2pcs screws for unlocking the front bezel with the panel module, and then use a proper tool to disconnect the panel lamp cable, LVDS cable and function key board from the connector of the main board.(No.1~2 screw size=M1.6x2.2, Torque=0.5±0.1kgfxcm)2Use a Philips-head screwdriver to remove 4pcs screws for unlocking bracket, move away the bracket and then remove 1pcs screw for unlocking the front bezel from the panel module, and then remove the front bezel carefully.(No.1~5 screw size=M3x4, Torque=3±0.5kgfxcm)Use a Philips-head screwdriver to remove 3pcs screws for unlocking bracket with panel module.(No.1~3 screw size=M3x2.8, Torque=3±0.5kgfxcm)132S8S9Put the front bezel with function key board into a fixture, tear off the mylar, then use a Philips-head screwdriver to remove 3pcs screws for unlocking the function key board with front bezel.(No.1~3 screw size=M0.2x2.4, Torque=1±0.2kgfxcm)S10321152341
3
Turn over the bracket chassis module. Use a Philips-head screwdriver to remove 5pcs screws for unlocking the main board. (No.1~3 screw size=M3x7.5, Torque=7.5±0.5kgfxcm)S13DELL S2719DMPut the bracket chassis on a protector cushion, then use a Philips-head screwdriver to remove 4pcs screws for unlocking the hinge.(No.1~4 screw size=M3x5.3, Torque=7.5±0.5kgfxcm)Disconnect the panel lamp cable from the connector os the panel module, then remove bracket and put it on a protect cushion for later disassembling. Unplug the LVDS cable and panel lamp cable from the connectors of panel module. Tear off the mylar tape which is sticked on the specific position of the back of panel, and then use a Philips-head screwdriver to remove 3pcs screws for unlocking the panel module.(No.1~3 screw size=M3x2.7, Torque=3~4kgfxcm)S11312S121342Remove the main board from the disconnect all of the cables.bracket chassis module by taking out the panel lamp cable from the hole of the bracket carefully, and then S1424135
The following substances, preparations, or components should be disposed of or
recovered separately from other WEEE in compliance with Article 4 of EU Council
Directive 75/442/EEC.
Capacitors / condensers (containing
PCB/PCT)
No used
Mercury containing components
No used
Batteries
No used
Printed circuit boards (with a surface
greater than 10 square cm)
Product has printed circuit boards (with a
surface greater than 10 square cm)
Component contain toner, ink and
liquids
No used
Plastic containing BFR
No used
Component and waste contain
asbestos
No used
CRT
No used
Component contain CFC, HCFC, HFC
and HC
No used
Gas discharge lamps
No used
LCD display > 100 cm2
Product has an LCD greater than 100 cm2
External electric cable
Product has external cables
Component contain refractory
ceramic fibers
No used
Component contain radio-active
substances
No used
Electrolyte capacitors (height
> 25mm, diameter > 25mm)
Product has electrolyte capacitors (height >
25mm, diameter > 25mm)
3. Tools Required
List the type and size of the tools that would typically can be used to disassemble the
product to a point where components and materials requiring selective treatment
can be removed.
Tool Description:
- Screwdriver (Phillip head) #1
- Screwdriver (Phillip head) #2
- Penknife
- Soldering iron and absorber
2. Product material information
4DELL S2719DM
Autres manuels pour S2719DM
1
Autres manuels Dell Moniteur
Dell
Dell P2418HT Instructions d'utilisation
Dell
Dell P1913 Manuel utilisateur
Dell
Dell S2421HS Manuel utilisateur
Dell
Dell C8618QT Manuel utilisateur
Dell
Dell E156FPc Manuel utilisateur
Dell
Dell P2222H Manuel utilisateur
Dell
Dell KX7P0 Manuel utilisateur
Dell
Dell Professional P2412H Manuel de la liste des pièces
Dell
Dell E1709W Manuel utilisateur
Dell
Dell E772p Manuel utilisateur
Dell
Dell S1909WFP Manuel utilisateur
Dell
Dell ST2010 - 20" LCD Monitor Manuel utilisateur
Dell
Dell E773c Series Manuel utilisateur
Dell
Dell C5519Q Manuel
Dell
Dell S2317HWI Manuel utilisateur
Dell
Dell S2317HWI Manuel utilisateur
Dell
Dell 1708FP - UltraSharp - 17" LCD Monitor Manuel utilisateur
Dell
Dell UltraSharp UP3017 Manuel utilisateur
Dell
Dell U2212HM Manuel utilisateur
Dell
Dell P2214Hb Manuel utilisateur
