Dell E228WFP Manuel utilisateur
Manuals
Documentation
Back to Contents Page
Back to Contents Page
About Your Monitor
Dell™ E228WFP Flat Panel Monitor User's Guide
Front View
Back View
Bottom View
Side View
Monitor Specifications
Caring for your Monitor
Front View
1. Input source select button
2. OSD menu / select button
3. Brightness & Contrast / Down (-) button
4. Auto-adjust / Up (+) button
5. Power button (with power light indicator)
Back View
http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (1 of 8)8/28/2007 8:59:03 AM
Documentation
1 VESA mounting holes (100mm) (Behind
attached VESA plate) Use to mount the monitor with VESA compliance (100mm) bracket.
2 Barcode serial number label Refer to this label if you need to contact Dell for technical support.
3 Security lock slot Use a security lock with the slot to help secure your monitor.
4 Dell Soundbar mounting brackets Attach the optional Dell Soundbar.
5 Regulatory rating label List the regulatory approvals.
6 Stand removal button Press to release the stand from the monitor.
7 Cable management hole Help organize cables by placing them through the hole.
Bottom View
1 Power connector Insert the power cable.
2 DVI connector Connect your computer DVI cable.
3 VGA connector Connect your computer VGA cable.
Side View
http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (2 of 8)8/28/2007 8:59:03 AM
Documentation
Left side Right side
Monitor Specifications
Power Management Modes
If you have VESA's DPM™ compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. This is referred to as 'Power Save Mode'*. If input from keyboard, mouse, or other input devices is detected by the
computer, the monitor automatically 'wakes up'. The following table shows the power consumption and signaling of this automatic power saving feature:
VESA Modes Horizontal Sync Vertical Sync Video Power Indicator Power Consumption
Normal operation Active Active Active Green 45 W (typical)
Active-off mode Inactive Inactive Blanked Amber Less than 2 W
Switch off - - - Off Less than 1 W
NOTE: The OSD only functions in the 'normal operation' mode. One of the following messages appears when the “menu” or “plus” buttons are pressed
when in Active-off mode.
1. Analog Input
In Power Save Mode
Press Computer Power Button
or Any Key on Keyboard or Move Mouse
or
2. Digital Input
In Power Save Mode
Press Computer Power Button
or Any Key on Keyboard or Move Mouse
Activate the computer and 'wake up' the monitor to gain access to the OSD.
This monitor is ENERGY STAR-compliant as well as TCO '99 power management compatible.
http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (3 of 8)8/28/2007 8:59:03 AM
Documentation
* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.
Pin Assignments
15-pin D-Sub connector
Pin Number Monitor Side of the 15-pin Side Signal Cable
1 Video-Red
2 Video-Green
3 Video-Blue
4 GND
5 Self-test
6 GND-R
7 GND-G
8 GND-B
9 DDC +5V
10 GND-sync
11 GND
12 DDC data
13 H-sync
14 V-sync
15 DDC clock
24-pin Digital-Only DVI Connector
Note: Pin 1 is at the top right.
http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (4 of 8)8/28/2007 8:59:03 AM
Documentation
Pin Signal Assignment Pin Signal Assignment Pin Signal Assignment
1 T.M.D.S. Data 2- 9 T.M.D.S. Data 1- 17 T.M.D.S. Data 0-
2 T.M.D.S. Data 2+ 10 T.M.D.S. Data 1+ 18 T.M.D.S. Data 0+
3 T.M.D.S. Data 2 Shield 11 T.M.D.S. Data 1 Shield 19 T.M.D.S. Data 0 Shield
4 No Pin 12 No Pin 20 No Pin
5 No Pin 13 No Pin 21 No Pin
6 DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield
7 DDC Data 15 Ground (for +5V) 23 T.M.D.S. Clock +
8 No Connect 16 Hot Plug Detect 24 T.M.D.S. Clock -
Plug and Play Capability
You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so that the system can configure itself and optimize the
monitor settings. If desired, you can select different settings, but in most cases monitor installation is automatic.
General
Model number E228WFP
Screen type Active matrix - TFT LCD
Screen dimensions 22 inches (22-inch viewable image size)
Preset display area:
Horizontal 473.76 mm (18.65 inches)
Vertical 296.1 mm (11.66 inches)
Pixel pitch 0.282 mm
Viewing angle 160 (vertical) typ, 160 (horizontal) typ
Luminance output 300 CD/m (typ)
Contrast ratio 800 to 1 (typ)
Faceplate coating Antiglare with hard-coating 3H
Backlight CCFL edgelight system
Response Time 5ms typical
Resolution
Horizontal scan range 30 kHz to 83 kHz (automatic)
http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (5 of 8)8/28/2007 8:59:03 AM
Documentation
Vertical scan range 56 Hz to 75 Hz (automatic)
Optimal preset resolution 1680 x 1050 at 60 Hz
Highest preset resolution 1680 x 1050 at 60 Hz
Video display capabilities(DVI HD playback) 480p/576p/720p
Preset Display Modes
Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock
(MHz) Sync Polarity (Horizontal/
Vertical)
VESA, 720 x 400 31.5 70.0 28.3 -/+
VESA, 640 x 480 31.5 60.0 25.2 -/-
VESA, 640 x 480 37.5 75.0 31.5 -/-
VESA, 800 x 600 37.9 60.3 49.5 +/+
VESA, 800 x 600 46.9 75.0 49.5 +/+
VESA, 1024 x 768 48.4 60.0 65.0 -/-
VESA, 1024 x 768 60.0 75.0 78.8 +/+
VESA, 1152 x 864 67.5 75.0 108 +/+
VESA, 1280 x 1024 64.0 60.0 135.0 +/+
VESA, 1280 x 1024 80.0 75.0 135.0 +/+
VESA, 1680 x 1050 65.0 60.0 146.25 +/+
Electrical
Video input signals Analog RGB, 0.7 Volts +/-5%, positive polarity at 75 ohm input impedance
Digital DVI-D TMDS, 600mV for each differential line, positive polarity at 50 ohm input impedance with HDCP support
Synchronization input signals Separate horizontal and vertical synchronizations, polarity-free TTL level
AC input voltage / frequency / current 100 to 240 VAC / 50 or 60 Hz + 3 Hz / 1.5A
Inrush current 120V:30A (Max.)
240V:60A (Max.)
Physical Characteristics
Connector type 15-pin D-subminiature, blue connector; DVI-D, white connector
Signal cable type Digital: Detachable, DVI-D, Solid pins, shipped detached from the monitor
Analog: Detachable, D-Sub, 15pins, shipped attached to the monitor
Dimensions (with stand):
Height 16.10 inches (409.10 mm)
http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (6 of 8)8/28/2007 8:59:03 AM
Documentation
Width 20.12 inches (511.14 mm)
Depth 5.87 inches (149.16 mm)
Dimensions: (without stand)
Height 13.13 inches (333.54 mm)
Width 20.12 inches (511.14 mm)
Depth 2.56 inches (65.00 mm)
Stand dimensions:
Height 11.92 inches (302.83 mm)
Width 12.20 inches (309.93 mm)
Depth 5.90 inches (149.98 mm)
Weight with packaging 20.94 lbs (9.5 kg)
Weight with stand assembly and cables 15.65 lbs (7.1 kg)
Weight without stand assembly
(For wall mount or VESA mount considerations - no cables)
11.46 lbs (5.2 kg)
Weight of stand assembly 2.65 lbs (1.2 kg)
Environmental
Temperature:
Operating 5 to 35C (41 to 95F)
Nonoperating Storage: -20 to 60C (-4 to 140F)
Shipping: -20 to 60C(-4 to 140F)
Humidity:
Operating 10% to 80% (noncondensing)
Nonoperating Storage: 5% to 90% (noncondensing)
Shipping: 5% to 90%(noncondensing)
Altitude:
Operating 3,657.6m (12,000 ft) max
Nonoperating 12,192 m (40,000 ft) max
Thermal dissipation 256.08 BTU/hour (maximum)
119.5 BTU/hour (typical)
Caring for Your Monitor
CAUTION: Read and follow the safety instructions before cleaning the monitor.
CAUTION: Before cleaning the monitor, unplug the monitor power cable from the electrical outlet.
http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (7 of 8)8/28/2007 8:59:03 AM
Documentation
●To clean your antistatic screen, slightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.
●Use a slightly-dampened, warm cloth to clean the plastics. Avoid using detergent of any kind as some detergents leave a milky film on the plastics.
●If you notice a white powder when you unpack your monitor, wipe it off with a cloth. This white powder occurs during the shipping of the monitor.
●Handle your monitor with care as darker-colored plastics may scratch and show white scuff marks more than lighter-colored monitor.
●To help maintain the best image quality on your monitor, use a dynamically changing screen saver and power off your monitor when not in use.
You are here: Dell USA > Support Home Page
© 2007 Dell | About Dell | Terms of Sale | Unresolved Issues | Privacy | Contact | Site Map | Feedback Top
Large Text
sn AP24
http://support.dell.com/support/edocs/monitors/E228WFP/En/about.htm (8 of 8)8/28/2007 8:59:03 AM
Autres manuels pour E228WFP
5
Table des matières
Autres manuels Dell Moniteur
Dell
Dell U2211H Manuel utilisateur
Dell
Dell E1709W Manuel utilisateur
Dell
Dell S2721HS Manuel utilisateur
Dell
Dell P2312H Manuel utilisateur
Dell
Dell E176FP - 17" LCD Monitor Manuel utilisateur
Dell
Dell S2230MX Instructions d'utilisation
Dell
Dell SX2210WFP Manuel utilisateur
Dell
Dell E2219HN Manuel utilisateur
Dell
Dell P2422HB Instructions d'utilisation
Dell
Dell ST2421LB Manuel utilisateur
Dell
Dell D1918H Manuel utilisateur
Dell
Dell U2312HM Manuel de la liste des pièces
Dell
Dell S2230MX Mode d’emploi
Dell
Dell P2714T Manuel utilisateur
Dell
Dell UltraSharp 1907FP Manuel utilisateur
Dell
Dell S2417DG Manuel utilisateur
Dell
Dell E198FP Manuel utilisateur
Dell
Dell P2211H Manuel utilisateur
Dell
Dell E2423HN Manuel utilisateur
Dell
Dell E2414H Manuel utilisateur
