DCS RF24TR2 Manuel

RF24TR2, RF24TL2, RF24BTR2, RF24BTL2

OUTDOOR BEER DISPENSER

USER/INSTALLATION GUIDE

US CA

NOTE

!CAUTION

Contents:

Safety information ...............................................................2

Unpacking your appliance ...................................................3

Warranty registration............................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Product dimensions RF24T.................................................8

Using your Electronic control...............................................9

Using your beer dispenser.................................................10

Tap equipment and assembly.........................................10

CO2 regulator.................................................................14

Drain kit...........................................................................15

Care and cleaning ............................................................15

Cleaning the drain sump................................................15

Keg coupler cleaning.....................................................16

Faucet cleaning ............................................................16

Front grille .....................................................................16

Cabinet...........................................................................16

Interior.............................................................................16

Long term storage / winterization .......................................17

Stainless steel maintenance ............................................19

Door alignment .................................................................20

Energy saving tips .............................................................20

Troubleshooting.................................................................21

Obtaining service .............................................................21

Warranty ............................................................................22

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

!WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

CONTENTS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals

known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals

known to the State of California to cause birth defects or

other reproductive harm..

NOTE

!CAUTION

A Message To Our Customers

Thank you for selecting this DCS Outdoor Refrigerator.

Because of this appliances’ unique features we have devel-

oped this Use and Care and Installation Guide. It contains

valuable information on how to properly install, operate and

maintain your new appliance for years of safe and enjoy-

able operation.

For your convenience, product questions can be answered

by a DCS Customer Care Representative at

1-888-936-7872, or email: customer.care@sherpaykel.com

NOTE: Please write the Model, Code, and Serial Number

on this page for references (the serial plate is located on

the upper left side, inner wall).

MODEL NUMBER:

CODE:

SERIAL NUMBER:

NOTE: Inspect the product to verify that there is no ship-

ping damage. If any damage is detected, call the shipper

and initiate a damage claim. DCS by Fisher & Paykel is not

responsible for shipping damage.

DO NOT discard any packing material (box, pallet, straps)

until the unit has been inspected.

Help Prevent Tragedies

Child entrapment and suffocation are not problems of the

past. Junked or abandoned refrigerators are still dangerous

- even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please follow

the instructions below to help prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not easily

climb inside.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Dispose of the plastic bags which can be a suffocation

hazard.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

!WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

UNPACKING YOUR APPLIANCE

!CAUTION

Figure 1

Front Leveling

Legs

Front Grille,

keep this area

open.

Rear

Leveling

Legs

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specifications, the recom-

mended installation location temperature range is from 50

to 100°F (10to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unobstructed.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean (See Figure 1). The use of a custom

made grille is not recommended as it may restrict air ow.

INSTALLING YOUR APPLIANCE

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The

overall height of your appliance may be adjusted between

the minimum, 333⁄4" (85.7 cm), by turning the leveling leg in

(CW ↷) and the maximum, 343⁄4" (88.3 cm) by turning the

leveling leg out (CCW ↶).

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 2).

Figure 2

Front grille screw

Front grille

NOTE

Figure 5

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 5). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

INSTALLING YOUR APPLIANCE

Figure 3

Figure 4

Do not remove

ground prong

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

!WARNING

!CAUTION

NOTE

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

Figure 6

Bottom View of

Beer dispenser

Anti-Tip

Bracket Leveling Leg

Front of cabinet

211⁄2"

(54.6 cm)

Step by step instructions for locating the

position of the bracket:

1) Decide where you want to place the beer dispenser.

Slide it into place, being careful not to damage the oor,

leaving 1" (2.5 cm) of clearance from the rear wall to allow

room for the anti-tip bracket.

2) Raise the rear leveling legs approximately 1⁄4" (6 mm) to

allow engagement with the anti-tip bracket. Level the unit

by adjusting all the leveling legs as required. Turning the

leveling leg counterclockwise will raise the unit and clock-

wise will lower the unit.

3) Make sure the beer dispenser is in the desired location,

then mark on the oor the rear and side corner of the cabi-

net where the anti-tip bracket will be installed. If the instal-

lation does not allow marking the rear corner of the cabinet,

then make temporary lines on the oor marking the front

corner of the cabinet, excluding the door. Slide the beer

dispenser out of the way. From the temporary line extend

the sidewall line back 211⁄2" (54.6 cm) as shown in Figure 6.

4) Align the anti-tip bracket to the marks on the oor so

the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 211⁄2" (54.6 cm) line (Rear of cabinet

line).

5) Fasten the anti-tip bracket to the oor using the supplied

screw. (See Figure 7).

6) Slide the cabinet back into position, making sure the rear

cabinet leveling leg slides under the anti-tip bracket engag-

ing the slot.

Floor Mount Installation

The anti-tip bracket is to be located on the oor in the left or

right rear corner of the beer dispenser as shown in

Figure 6.

!WARNING

•ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

•FOLLOW THE INSTRUC-

TIONS BELOW

!WARNING

If your refrigerator is not located under a counter

top (free standing), you must use an anti-tip device

installed as per these instructions. If the refrigerator is

removed from its location for any reason, make sure

that the device is properly engaged with the anti-tip

bracket when you push the refrigerator back into the

original location. If the device is not properly engaged,

there is a risk of the refrigerator tipping over, with the

potential for property damage or personal injury.

If installing on a concrete oor, concrete fasteners are

required, (not included with the anti-tip kit).

Any nished ooring should be protected with appropriate

material to avoid damage when moving the unit.

NOTE

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

"V" notches

in bracket

"V" notches

in bracket

When the oor mounted anti-tip bracket is used the mini-

mum adjusted height of the cabinet is increased by

3⁄8" (9 mm).

Figure 7

Front of cabinet line

Rear of cabinet line

Figure 7a

211⁄2"

(54.6 cm)

Rear Leveling leg

Screw

Side of cabinet line

"A"

"B"

"C"

"D"

"E"

"H"

"G"

"F"

"J"

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

RF24T

RF24BT

24" (61 cm)

24 ½" (62 cm)

(with optional

DCS side trim kit)

**34" to 35"

(86.4 to 88.9 cm) *237⁄8"

(60.7 cm)

333⁄4" to 343⁄4"

(85.7 to 88.3 cm)

2323⁄32"

(60.2 cm)

261⁄4"

(66.7 cm)

4613⁄32"

(117.9 cm)

261⁄4"

(66.7 cm)

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS***

PRODUCT

WEIGHT

RF24T, RF24BT 115V/60Hz/15A 140 lbs

(63.6 kg)

Figure 9

211⁄2"

(54.6 cm)

121⁄4"

(31.1 cm)

1115⁄16"

(30.3 cm)

11"

(27.9 cm)

Figure 8

* Depth dimension of rough-in opening may vary depend-

ing on each individual installation. To recess entire door "F"

dimension plus 1" (2.5 cm) for thickness of power cord plug

is required.

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

*** A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

PRODUCT DIMENSIONS

Figure 8a

USING YOUR ELECTRONIC CONTROL

Figure 10

Electronic control

Control Function Guide

Function Command Notes

ON/OFF Press and hold for 5 seconds. Unit will immediately turn ON or OFF.

Leave Interior Light On Press and release to leave interior light on for

3 hours; press again to deactivate.

After 12 hours, factory default is restored; light will turn on when

door is open.

Adjust Temperature Press or and release.

When the display is ashing, press or to adjust the set

point temperature. Note: temperature displayed is the actual

temperature inside unit.

Toggle Between oF / oC Hold and for 5 seconds. The display will change units.

Enable Sabbath Mode Press and hold for 5 seconds and release.

The oF / oC symbol will ash briey after 5 seconds. Interior

light and display will go dark and remain so until user resets

mode - unit continues to operate.

Disable Sabbath Mode Press , hold for 5 seconds and release. Display and interior light return to normal operation.

Showroom Mode Hold and for 5 seconds.

Display will show for 2 seconds. Interior light and display

will function normally, but the compressor and fans will not be

energized. Repeat command to return to normal operation.

Display will show for 2 seconds.

NOTE

Temperature displayed reects actual temperature inside unit. If the

temperature displayed is di󰀨erent than selected, the unit is progressing

towards the selected temperature. Time to reach set point varies based

upon ambient temperature, temperature of product loaded, door

openings, etc. DCS recommends allowing the unit to reach set points

before loading.

USING YOUR BEER DISPENSER

Tap Equipment and Assembly

Your dispensing kit includes the following parts:

Polished stainless steel tower with clear beer line (single

or double dispense)

Tower Gasket

Phillips oval head screws

Knob for Tower (Faucet Handle)

Keg coupler(s)

CO2regulator with red gas line(s) attached

Empty 5 pound CO2tank

Plastic clamp(s) large and small

Faucet wrench

Tools required for installation:

Flat bladed screwdriver

Phillips screwdriver

Pliers

Adjustable wrench or a 11⁄8" open end wrench

1⁄2" open end wrench

Barrel Sizes

1/6 barrel 1/4 Barrel 1/2 Barrel

Height 235⁄16"

(59.2 cm)

1413⁄16"

(37.6 cm)

235⁄16"

(59.2 cm)

Diameter 91⁄4"

(23.5 cm)

17"

(43.2 cm)

17" to 171⁄4"

(43.2 to 43 cm)

Gallons 5.16 7.75 15.5

#12 ounce

Glasses 60 82 163

This beer dispensing unit will support 1⁄2barrel or 1⁄4bar-

rel. The double draft tower units can support two sixth (1⁄6)

barrels of beer. See chart below for quantity of beer in each

barrel size.

Table A

Table B

Keg Size #of kegs per

5 pound CO2 Tank

5 gallon Corny 15 to 22

1/6 barrel 14 to 21

1/4 Barrel 10 to 14

1/2 Barrel 5 to 7

CO2 can be dangerous. If it becomes difcult to

breathe and/or your head starts to ache, a high

concentration of carbon dioxide may be present.

Leave the area immediately.

• The CO2 tank must always be connected to the

regulator. Never connect the tank to the keg.

• The CO2tank must be securely mounted in the

upright position. Secure it with the chain pro-

vided.

• Never drop or throw the CO2tank.

• Keep the CO2tank away from heat.

• Ventilate the area after a CO2leak.

!WARNING

1. Remove shelving and packaged components from the

interior of the refrigerator before beginning the assem-

bly process.

2. Take your empty 5 pound CO2tank to your local gas

supply dealer to be lled. You can usually nd them in

your "yellow pages" under "Welding Supply" or "Fire

Protection". One 5 pound tank can process many kegs

(see table "B") Your dealer should supply you with a

new plastic washer every time the tank is lled. This

washer is used at the regulator to tank connection. See

Figure 15 and 22 on page 11. Replace the old washer

with the new one whenever the tank is relled.

3. Tower mounting (if you are installing the unit under a

counter skip to step 4). If you are mounting the tower

directly to the top of the refrigerator, rst remove the

four screws from the top of the refrigerator. Feed the

clear beer line through the tower gasket and the large

hole in the refrigerator top. Align the 4 holes in the

tower with the 4 holes in the refrigerator top and secure

the tower with the 4 screws removed previously. Skip to

step 5.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DCS Distributeur de boissons

DCS

DCS UR624 Manuel utilisateur

DCS

DCS RF24TR Manuel

Manuels Distributeur de boissons populaires d'autres marques

PEGAS

PEGAS Evolution Manuel utilisateur

Ugolini

Ugolini MT micro Manuel utilisateur

Bunn

Bunn SLCA-7 Instructions d'installation

Gekkeikan

Gekkeikan Sake Machine Manuel utilisateur

Olympia

Olympia DH709 Manuel utilisateur

Marco

Marco ECOSMART PB10 Manuel utilisateur

Marvel

Marvel ML24BN Series Manuel

Cecilware

Cecilware 2K-GB-LD Manuel

Sure Vend

Sure Vend 673 Manuel utilisateur

Cornelius

Cornelius 2 Flavor Post-Mix Cold Coffee Dispenser Quest... Manuel utilisateur

Nostalgia Electrics

Nostalgia Electrics KEG7000SS Manuel utilisateur

Bunn

Bunn LCR-3 HV Guide de dépannage

Servend

Servend SV-200 Manuel utilisateur

EdgeStar

EdgeStar VBR440 Manuel utilisateur

Cornelius

Cornelius A.B.S. Unit Manuel utilisateur

CDS AUTOMATEN

CDS AUTOMATEN ML-16C2-C Manuel utilisateur

Siemens

Siemens GA 3000 Manuel d'instructions et de sécurité

Cornelius

Cornelius FCB V4 Caractéristiques techniques