Datamax M-Class Mark II Manuel utilisateur

Media Hubs

92-2491-01 Rev.B

Overview

This document describes the contents and installation of the Media Hub options for the M-Class MII

printer. Only qualified service personnel should perform this installation. After verifying the kit contents

and the tools needed, follow the steps below to install the option.

Contents

The contents of the Media Hub Kit differ according to kit number:

(3-Inch Media Hub Kit) contains the following items:

11.5-Inch Media Hub Assembly

2Philips Screw

3Hub Adapter

(40-mm Media Hub Kit) contains the following items:

140-mm Media Hub Assembly (P/N 15-3199-01)

2Philips Screw (P/N 10-2903-04)

Tools Required

A Phillips screwdriver is needed for installation.

Installation

CAUTION

Only qualified service personnel should perform this installation. Always wear a wrist

strap and follow standard ESD prevention measures when handling any printer

circuit card assembly.

A) Turn OFF the Power Switch

and unplug the power cord

from the AC Receptacle.

Disconnect the interface

cable(s).

Power Switch

AC Receptacle

B) Remove the Cover Screws

on the outside of the printer.

Cover Screws

C) Raise the Cover. Loosen the

Cover Screws on the

Centerplate then remove the

Cover.

Cover Screws

Cover

Centerplate

D) Disconnect the cables from

the Main Logic Card.

Main Logic

Card

E) Remove the Screws that

secure the Main Logic Card

and the Fill Plate to the Card

Cage. Remove the Fill Plate

then slide the Main Logic

Card out of the printer.

Screws

Fill

Plate

Card Cage

Main Logic

Card

F) Remove the Hanger Screws

that secure the Media

Hanger to the Centerplate

and then remove the Media

Hanger.

Hanger

Screws

Media

Hanger

Centerplate

G) Slide the Main Logic Card

into the Card Cage and

replace the Fill Plate. Secure

the Main Logic Card and the

Fill Plate using the previously

removed Screws. Reconnect

all the cables to the Main

Logic Card.

J11 J9

J14

J10

J12

J16

Main Logic Card

H) Remove the Ground Strap

Screw and Lock Washer,

four Power Supply Screws,

and two Line Filter Screws.

Remove the Line Filter

Bracket and then remove the

Power Supply.

Power Supply

Screws

Ground Strap

Screw and Lock Washer

Power Supply

Line Filter

Bracket

Line Filter

Screws

I) Place the Media Hub

Assembly*(Item 1) into the

Hub Mount. Secure the

Shaft to Hub Mount using

the Screw (Item 2), ensuring

that both are completely

tightened before proceeding.

Media Hub Assembly

Screw

Shaft

Hub Mount

* 3-Inch Media Hub Kit installers – see the note at the end of this document.

J) Install the Power Supply

then place the Line Filter

Bracket onto the Line Filter.

Secure the Power Supply

using the Power Supply

Screws and the Line Filter

Screws.

Power Supply

Screws

Line Filter

Bracket

Line Filter

Bracket Screws

K) Insert the Ground Strap

Screw into the Lock Washer

and the Ground Strap Lug.

Then secure the Ground

Strap Lug to the chassis

using the Ground Strap

Screw and Lock Washer.

Ground Strap Screw

and Lock Washer

Ground Strap Lug

L) Check all Power Supply cable

connections then place the

Cover onto the printer. Install

and tighten the Cover

Screws on the outside of the

printer.

Cover Screws

M) Tighten the Cover Screws on

the Centerplate.

Cover Screws

Centerplate

N) Connect the interface

cable(s). Plug the power cord

into the AC Receptacle and

turn ON the Power Switch.

This completes the

installation process; refer to

the Operator’s Manual for

media loading instructions.

Power Switch

AC Receptacle



Note: The 3-Inch Media Hub

Kit is configurable:

To install the Hub

Adapter (Item 3),

align the Tabs then

slide the Hub

Adapter over the

1.5-Inch Hub

Assembly until it

seats in place; or,

To remove the Hub

Adapter, grasp and

pull.

1.5-Inch Hub

Assembly

Hub Adapter

Tabs

Autres manuels pour M-Class Mark II

Table des matières

Autres manuels Datamax Imprimante

Datamax

Datamax Mark II E-4205e Manuel utilisateur

Datamax

Datamax MICROFLASH 4T Manuel utilisateur

Datamax

Datamax ST-3210 Manuel utilisateur

Datamax

Datamax MICROFLASH 4TE Manuel utilisateur

Datamax

Datamax PrintPAD CN70 Manuel utilisateur

Datamax

Datamax 88-2312-01 Manuel utilisateur

Datamax

Datamax MP-Compact4 Manuel

Datamax

Datamax PrintPAD Series Manuel utilisateur

Datamax

Datamax I-4206 Manuel utilisateur

Datamax

Datamax DMX E E-4204 Manuel utilisateur

Datamax

Datamax Label Printer Manuel utilisateur

Datamax

Datamax Ex2 Manuel utilisateur

Datamax

Datamax E-Class Mark II Manuel utilisateur

Datamax

Datamax H-Class GPI O Option Manuel utilisateur

Datamax

Datamax H-4212X Manuel utilisateur

Datamax

Datamax h-class h-8308p Manuel utilisateur

Datamax

Datamax RL4 Manuel utilisateur

Datamax

Datamax ST-3210 Manuel utilisateur

Datamax

Datamax Apex 3 Manuel utilisateur

Datamax

Datamax Workstation w1110 Manuel utilisateur

Datamax

Datamax W-6208 Manuel utilisateur

Datamax

Datamax I-Class Mark II Manuel utilisateur

Datamax

Datamax Ex2 Manuel utilisateur

Datamax

Datamax OC-3 Series Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur