Dataman 48UXP Manuel utilisateur
Dataman-48UXP
Intelligent Universal Programmer
User′
′′′s Manual
Copyright Notice
This document is copyrighted, 2000, 2001, 2002 by DATAMAN
PROGRAMMERS LTD. All rights are reserved. DATAMAN
PROGRAMMERS LTD. reserves the right to make improvements
to the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written
permission of DATAMAN PROGRAMMERS LTD. Information
provided in this manual is intended to be accurate and reliable.
However, DATAMAN PROGRAMMERS LTD. assumes no
responsibility for its use, nor for any infringements upon the rights
of third parties which may result from its use.
Acknowledgments
IBM, PC AT and VGA are trademarks of International Business
Machines Corporation.
MS-DOS and MS-Windows are trademarks of Microsoft
Corporation.
Howtousethismanual
Thank you for purchasing the Dataman-48UXP intelligent
universal Programmer. We designed this manual to help you
quickly and easily set up and use your Dataman-48UXP. You
can use the manual in two ways:
Step by step:
The manual should be used in conjunction with the On-line
help contained in the Dataman-48UXP software. Once you
have installed the Dataman-48UXP hardware and the
software, you should not need this manual again. You can
just press ′Fl′in the program and context sensitive help will
guide you through the processes.
Quick start:
Our special Quick Start section gives experienced users the
information they need to setup the Dataman-48UXP and
software, and basic guidelines on using the Dataman-48UXP
If you need more information, you can refer to the rest of the
manual. If you have any problems, you can work through the
manual step by step for easy troubleshooting. If you have any
questions, feel free to call your local distributor or sales
representative.
Software Updates:
Please visit our web at www.dataman.com for periodical
software updates.
PackingList
Before you begin installing your Dataman-48UXP, please
make sure that the following materials have been shipped:
1. Dataman-48UXP intelligent universal programmer.
2. Parallel cable (1.0 meter).
3. USB cable (1.8meter).
4. CD ROM containing the EPP interface software for
Windows support Win 2000, Win 95/98/ME, Win XP and
Win NT (NT 4.0 and latest version).
5. CD ROM containing the USB interface software for
Windows support Win 98/ME, Win 2000, and Win XP.
6. Power cord.
Contents
Chapter 0 Quick Start ................................................................ 0-1
Quick Start......................................................................... 0-2
Chapter 1 General Information .................................................. 1
Introduction........................................................................ 2
Features.............................................................................. 2
Using the Dataman-48UXP Software................................. 4
Chapter 2 Installation................................................................. 5
Minimum PC System Requirements .................................. 6
Installing the Dataman-48UXP Hardware.......................... 6
Installing the Dataman-48UXP Software ........................... 6
Upgrading the Dataman-48UXP Software ......................... 7
Chapter 3 Command Hierarchy ................................................. 8
Dataman-48UXP Command Hierarchy.............................. 9
Chapter 4 Operation................................................................... 10
LED Display ...................................................................... 11
File Commands.................................................................. 11
Save Buffer to File ..................................................... 11
Load File to Buffer.....................................................14
Exit............................................................................. 19
Project File Commands...................................................... 20
Save Project................................................................ 20
Load Project............................................................... 20
Device Commands............................................................. 20
Change Device ........................................................... 20
Auto Select EPROM................................................... 23
Mass-production Mode............................................... 24
Editing the Buffer....................................................... 26
Modify Vector ............................................................ 30
Blank Checking a Device........................................... 33
Reading a Device........................................................ 33
Programming a Device............................................... 33
Verifying a Device...................................................... 34
Memory Protect/program configuration ..................... 35
Function Test.............................................................. 36
Erasing a Device......................................................... 37
Compare..................................................................... 37
Device Configuration................................................. 38
Options............................................................................... 39
Modify Programming Parameters............................... 39
Device Operation Options.......................................... 39
Parallel Port Selection................................................ 44
Statistic....................................................................... 45
Chapter 5 UsingAdapters.......................................................... 49
Adapter Requirements........................................................ 50
Appendix A Error Messages ...................................................... 57
Error Messages................................................................... 58
0
Quick Start
This section is for experience user only, after install the
Dataman-48UXP hardware and successfully install the system
software in your PC, user can follow the quick start section start
to program the device without go to the read this manual step
by step.
CHAPTER
QuickStart
After execution the Dataman-48UXP software, following Dataman-48UXP
screen will display:
It shows the firmware version of Dataman-48UXP, the parallel port
that connect to the Dataman-48UXP:
1) Select the chip to be programmed first.
Use the Hot Key “ALT-C”, then type the complete part number
of the chip to be programmed; or use the mouse to select the
desired part number.
2) Load the design file into the buffer.
Use the Hot Key “ALT-L”, then specify the origin of the file
and load.
3) Alternatively, you can read a master chip into the buffer instead
of a design file.
Read operation (Hot Key ALT-R), you can transfer the chip′s
contents into the buffer.
4) Insert blank chip of the same type into the ZIF sockets, set the
device operation option (Hot Key F4, detail of device option,
reference to chapter 4 of this manual) then press program (Hot
Key ALT-P).
5) To speed up throughput, user can change the mode to Mass
production mode (move the mouse to device, click the left key
of mouse moving the cursor to mass production mode and click
the left key of mouse again). After entering this mode, the
Dataman-48UXP will program chips automatically after the
chip has properly inserted into the socket of the
Dataman-48UXP.
6) If the chip has configuration byte for set up the oscillator type,
watch dog, code protect, etc in the chip. User need to enable
the configuration (Hot Key ALT-G) then edit the desired set up
in to the configuration byte, then perform memory
protect/program configuration in the SW to program the
configuration byte of the chip, the configuration menu only
available if the chip has this specific function.
7) Program the configuration byte or protect the chip can also be
done in single key press or in mass production mode without
need to press the memory protect separately, to achieve this
user need to enable the memory protect in the device operation
menu first then after perform program, the programmer will
program the main buffer then program the configuration byte
or protect the chip in sequence. For chip has memory protect
function, after the code protect bit been set and perform protect,
the chip will not allow to read back again and can not verify
too.
8) For a detailed explanation of the device operation options,
please refer to Chapter 3 and 4.
1
General Information
CHAPTER
Table des matières
Autres manuels Dataman Carte mère
Dataman
Dataman S4 Manuel utilisateur
Dataman
Dataman S6 Manuel utilisateur
Dataman
Dataman DATAMAN-448PRO2 Manuel utilisateur
Dataman
Dataman DATAMAN-848PRO2 Manuel utilisateur
Dataman
Dataman 448PRO2 Manuel utilisateur
Dataman
Dataman DATAMAN-848PRO2 Manuel utilisateur
Dataman
Dataman 448PRO2AP Manuel utilisateur
Dataman
Dataman 448PRO2AP-AU Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
