Datalogic DS2100A Manuel utilisateur

DS2100A

Laser Barcode Reader

Quick Reference Guide

The scanner is classified as a Class 2 laser

product according to EN 60825-1 regulations

and as a Class II laser product according to

CDRH regulations.

Disconnect the power supply when opening the

device during maintenance or installation to

avoid exposure to hazardous laser light.

There is a safety device which allows the laser to

be switched on only if the motor is rotating above

the threshold for its correct scanning speed.

The laser beam can be switched off through a

software command (see also the WinHost Help

On Line).

Figure A

Warning and Device Class Labels

4 8

Mounting Holes

Laser On LED

Good Read LED

External Trigger LED

Power On / Data TX LED

Warning and Device Class Labels

Accessory Mounting Holes

Laser Beam Output Window

For further details on product installation, see the

complete Installation Manual.

DS2100A can be configured through the WinHost

Windows-based software program available on the

installation CD-ROM.

For configuration it is necessary to create a cable

connecting the scanner to the PC as indicated in the

“How To Build A Simple Interface Test Cable” section of

this guide.

The laser diode used in this device is

classified as a class 3B laser product

according to EN 60825-1 regulations and as a

Class IIIb laser product according to CDRH

regulations. As it is not possible to apply a

classification label on the laser diode used in

this device, the following label is reproduced

below.

LASER LIGHT

AVOID EXPOSURE TO BEAM

CLASS 3B LASER PRODUCT

MAX. OUTPUT RADIATION 35 mW

EMITTED WAVE LENGTH 630~680 nm

TO EN 60825-1 (2001)

Laser Diode Class Label

Any violation of the optic parts in particular

can cause radiation up to the maximum level

of the laser diode (35 mW at 630 to 680 nm).

POWER SUPPLY

- This product is intended to be installed by Qualified

Personnel only.

- All Models:

This accessory device is intended to be supplied by a UL

Listed or CSA Certified Power Unit with «Class 2» or LPS

power source which supplies power directly to the

scanner via the 25-pin connector.

CAUTION-CLASS 3B LASER LIGHT

WHEN OPEN AVOID EXPOSURE TO BEAM

This product conforms to the applicable

requirements of 21CFR1040 at the date

of manufacture.

LASER LIGHT

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

MAX. OUTPUT RADIATION 1 mW

EMITTED WAVE LENGTH 630~680 nm

TO EN 60825-1:2001

CUS

218441

N2468

DS2100A QUICK GUIDE

Model Description:

DS2100A - X X X X

Optical Resolution

1 = Standard resolution

2 = High resolution

Communication Interface

2= RS232/RS485main + RS232 aux Optic Version

0 = Linear

1 = Raster R1

Performance

0 = Standard

4 = Testarossa ™

Reading Performance:

Version Reading Distance Max Code

Resolution

mm (mils)

Speed

scans/s

1XX0 40 mm (1.6 in) - 300 mm (11.8 in) on 0.50 mm (20 mils) codes 0.20 (8) 500 to 800

1XX4 50 mm (1.8 in) - 310 mm (11.8 in) on 0.50 mm (20 mils) codes 0.20 (8) 800 to 1000

2XX0 30 mm (1.2 in) - 90 mm (3.5 in) on 0.30 mm (12 mils) codes 0.15 (6) 500 to 800

2XX4 45 mm (1.8 in) - 100 mm (3.9 in) on 0.20 mm (8 mils) codes 0.12 (5) 800 to 1000

Technical Features:

ELECTRICAL FEATURES SOFTWARE FEATURES

Power Supply 10 –30 Vdc Readable Codes

Power Consumption Model XXX0: 3W

Model XXX4: 5W

Main Serial Interface Programmable:

RS232;

RS485 Full-Duplex/Half-

Duplex;

Auxiliary Interface RS232

EAN/UPC

(including Add-on 2 and Add-on 5)

Code 39

2/5 Interleaved

Code 128

EAN 128

Codabar

Code 93

Baudrates 150 to 115200

* = ACB readable

ISBT 128

Inputs

Pharmacode

External Trigger (optocoupled NPN or PNP) Headers and

Up to four header and four

Voltage max. 30 Vdc Terminators

terminator characters

Current Consumption 25 mA Operating Modes

On-Line, Automatic,

max.

Serial-On-Line, Test

Outputs

)

Configuration Modes Through menus using:

OUT1, OUT2 (optocoupled) WinHost utility

Host Mode (commands from

max. 40 Vdc one of the serial ports)

Collector Current 40 mA continuous; Code Selection Up to six different codes

max. 130 mA pulsed during one reading phase

Saturation 1V at 10 mA max. Decoding Safety Can enable multiple good

Power Dissipation 90 mW at 40 °C reads of the same code

max. (Ambient temp.) Special Functions ACB (Advanced Code Builder)

Motor Off

OPTICAL FEATURES

Light Source semiconductor laser diode Parameter Storage Non-volatile internal EEPROM

Wavelength In the range 630 to 680 nm ENVIRONMENTAL FEATURES

Safety Class Class 2 - EN 60825-1; CDRH Operating 0° to +40 °C (+32° to +104 °F)

Temperature

USER INTERFACE Storage -20° to +70 °C (-4° to +158 °F)

LED Indicators Laser ON, Good Read, Temperature

External Trigger, Humidity max 90% non condensing

Data TX / Power ON Vibration Resistance IEC 68-2-6 test FC 1.5 mm;

PHYSICAL FEATURES 10 to 55 Hz; 2 hours on each axis

Dimensions 68x83.6x34 mm

(2.7x3.29x1.3 in)

Shock Resistance IEC 68-2-27 test EA 30 G;

Weight 330 g.

(11.64 oz)

11 ms; 3 shocks on each axis

Protection Class IP65

DS2100A QUICK GUIDE

Accessories:

Name Description Part Number

GFC-2100 90° Reading Device 93A201000

GFC-2000 75° Reading Device 93A201080

INT-30

(for C-Box 100)

20 mA Current Loop Interface Board 93A151022

C-BOX 100/200 Connection Box 93ACC1510,93ACC1520

C-BOX 300/310 Connection Box Profibus 93A301000, 93A301030

C-BOX 400/410 Connection Box DeviceNet 93A301010, 93A301040

MEP-542/543 Photocell Kit NPN/PNP 93ACC1727, 93ACC1728

Electrical Connections:

DS2100A is equipped with a cable terminated by a 25-pin female D-sub connector for connection to the power

supply and input/output signals. You can bring system cables directly to the 25-pin connector or you can connect

the scanner directly to one of the various C-Box models and bring system wiring to it (see the relative C-Box

Installation Manual).

CAUTION

Do not connect GND and SGND to different (external) ground references. GND and SGND

are internally connected through filtering circuitry which can be permanently damaged if

subjected to voltage drops over 0.8 Vdc.

The details of the connector pins are indicated in the following table:

25-pin D-sub female connector pinout

Pin Name Function

13 VS Power supply input voltage +

25 GND Power supply input voltage -

1 CHASSIS Chassis Ground

9 VS External Trigger supply voltage +

18 EXT TRIG+ External Trigger +

19 EXT TRIG- External Trigger -

8 OUT1 + Output 1 +

11 OUT2 + Output 2 +

12, 22 OUT REF Output reference

20 RXAUX Auxiliary RS232

21 TXAUX Auxiliary RS232

23 CTSAUX Auxiliary handshake RS232

24 RTSAUX Auxiliary handshake RS232

6, 10, 14,

15, 16, 17 NC Not Connected

25-pin female connector

Pin RS232 RS485

Full-Duplex RS485

Half-Duplex

2 TX232 TX485+ RTX485+

3 RX232 RX485+

4 RTS232 TX485- RTX485-

5 CTS232 RX485-

7 SGND SGND SGND

DS2100A QUICK GUIDE

Mechanical Installation:

4.2

7.8

20°

2.5

R40

4.2

90°

13.8

17.5

2.5

4.2n°2

1 x 45° n° 2

23.3*

0.92

14.5

0.57

83.6

3.29

0.098

10.3

0.4

1.57

0.4

10.3

1.57

14.6

0.57

M 4 n° 4

1.3

inch

2.68

1.81

DS2100

* The quote refers to the scan line

Input/Output Connections:

INPUT NPN INPUT NPN MEP-543

EXT TRIG+

+ 5V

DS2100A EXTERNAL TRIGGER

Signal

Vext 30 Vdc max.

EXT TRIG-

Input NPN command using external power

MEP-543 Connector

DS2100A

+ 5V

25 GND

EXT TRIG+

EXT TRIG- 43

2 1

(brown)

(white)

(blue)

Input NPN command using MEP-543 Photocell

OUTPUT

EXTERNAL TRIGGER

DS2100A

Signal

+ 5V

25 GND Ground

EXT TRIG+

EXT TRIG-

Input NPN command using

DS2100A

power

USER INTERFACE

8/11

12/22 OUT REF

DS2100A

Vext 40 Vdc max.

Output open collector connections

INPUT PNP

+ 5V

DS2100A EXTERNAL TRIGGER

Signal

Ground

EXT TRIG+

EXT TRIG-

Vext 30 Vdc max.

Input PNP command using external power

max = 40 Vdc

max = 40 mA continuous

EXTERNAL TRIGGER

DS2100A

+ 5V

25 GND Ground

Signal

EXT TRIG+

EXT TRIG-

Input PNP command using DS2100A power

DS2100A

DS2100A QUICK GUIDE

Connectivity:

RS232 Main Interface Connections RS485 Main Interface Connections

RS232 Point-to-point layout RS485 Point-to-point layout

cMain Serial Interface (RS232) cMain Serial Interface (RS485 Full Duplex)

dAuxiliary Serial Interface (Local Echo) (RS232) dAuxiliary Serial Interface (Local Echo) (RS232)

eExternal Trigger (for On-Line Mode) eExternal Trigger (for On-Line Mode)

Pass-through layout Multiplexer layout

cMain Serial Interface (RS232) cMain Serial Interface (RS485 Half-Duplex)

dAuxiliary Serial Interface (RS232) dAuxiliary Serial Interface (Local Echo) (RS232)

eExternal Trigger (for On-Line Mode) eExternal Trigger (for On-Line Mode)

RS232 Master/slave layout RS485 Master/slave layout

cMain Serial Interface (Slaves RS232 only) cAuxiliary Serial Interface (RS232)

dAuxiliary Serial Interface (RS232) dMain Serial Interface (RS485 Half-Duplex)

eExternal Trigger (for On-Line Mode) eExternal Trigger

Host

DS2100

Terminal

Host

MX4000

Host

DS2100

Host

DS2100

Slave

DS2100

Slave

DS2100

Maste

Host

DS2100

Slave

DS2100

Slave

DS2400

Maste

Host

DS2100

Terminal

Host

DS2100

Terminal

DS2100A QUICK GUIDE

Reading Diagrams:

DS2100A-1200 (Standard Resolution, 500 scans/s)

CONDITIONS

Optic Version = Linear

Code = Interleaved 2/5 or Code 39

PCS = 0.90

Pitch angle = 0°

Skew angle = 15°

Tilt angle = 0°

*Code Reading Condition = Standard

* Parameter selectable in Winhost

(in)

120

100

120

(mm)

0 1 32 106(in)

45 7 89

0 20 40 60 80 100 120 140 160 180 200 220 240 260 (mm)

280

300

0.20 mm

(8 mils) ≥0.50 mm

(20 mils)

0.30 mm

(12 mils)

0.35 mm

(14 mils)

DS2100A-1200

Reading Distance vs Scanning Speed

2 10

(in)

0 20 40 60 80 100 120 140 160 180 200 220 240 260 (mm)

0.20 mm

280

300

0.30 mm

0.35 mm

0.50 mm

Distanc

Code

Resolution

500 scans/s

800 scans/s

DS2100A QUICK GUIDE

DS2100A-2200 (High resolution, 500 scans/s)

CONDITIONS

Optic Version = Linear

Code = Interleaved 2/5 or Code 39

PCS = 0.90

Pitch angle = 0°

Skew angle = 15°

Tilt angle = 0°

*Code Reading Condition = Standard

* Parameter selectable in Winhost

(in)

01 53(in)

010 20 30 40 50 60 70 80 90 100 110 120 130 (mm)

(mm)

0.15 mm

(6 mils)

0.20 mm

(8 mils)

≥0.30 mm

(12 mils)

DS2100A-2200

Reading Distance vs Scanning Speed

0 1 53(in)

0 10 20 30 40 50 60 70 80 90 100 110 120 130 (mm)

0.30 mm

0.20 mm

0.15 mm

500 scans/s

800 scans/s

Code

Resolution

Distance

DS2100A QUICK GUIDE

DS2100A-1204 Testarossa™ (Standard resolution, 1000 scan/s)

CONDITIONS

Optic Version = Linear

Code = Interleaved 2/5 or Code 39

PCS = 0.90

Pitch angle = 0°

Skew angle = 15°

Tilt angle = 0°

*Code Resolution:

High - for 0.30 mm (12 mils)

codes and smaller

Standard - for 0.50 mm (20 mils)

codes and greater

*Code Reading Condition = Standard

* Parameter selectable in Winhost

(in)

0 1 32 106(in)

45 789

0 20 40 60 80 100 120 140 160 180 200 220 240 260 (mm)

120

100

120

(mm)

280

300

0.15 mm

(6 mils)

0.20 mm

(8 mils)

0.30 mm

(12 mils) ≥0.50 mm

(20 mils)

DS2100A-2204 Testarossa™ - (High Resolution, 1000 scans/s)

CONDITIONS

Optic Version = Linear

Code = Interleaved 2/5 or Code 39

PCS = 0.90

Pitch angle = 0°

Skew angle = 15°

Tilt angle = 0°

*Code Resolution:

High - for 0.15 mm (6 mils) codes

and smaller

Standard - for 0.20 mm (8 mils)

codes

*Code Reading Condition = Standard

* Parameter selectable in Winhost

(in)

01 53(in)

010 20 30 40 50 60 70 80 90 100 110 120 130 (mm)

(mm)

0.12 mm

(5 mils)

0.15 mm

(6 mils)

≥0.20 mm

(

8 mils

)

DS2100A QUICK GUIDE

User Interface:

The following table contains the pinout for standard RS232 PC Host interface. For other user interface types

please refer to their own manual.

RS232 PC-side connections

1 5

9-pin male connector

2514

25-pin male connector

Pin Name Pin Name

2 RX 3 RX

3 TX 2 TX

5 GND 7 GND

7 RTS 4 RTS

8 CTS 5 CTS

How To Build A Simple Interface Test Cable:

The following wiring diagrams show a simple test cable including power, external (push-button) trigger and PC

RS232 COM port connections.

25-pin D-sub male

SGND

RXAUX

TXAUX

DS2100A

GND

9-pin D-sub female

GND

EXT TRIG+

Power Supply

VS (10 – 30 Vdc)

Power GND

Trigger

EXT TRIG-

Test Cable for DS2100A

DATALOGIC S.p.A.,

Via Candini, 2

40012 - Lippo di Calderara

Bologna - Italy

dichiara che

declares that the

déclare que le

bescheinigt, daß das Gerät

declare que el

DS2100A-XXXX Laser Scanner

e tutti i suoi modelli

and all its models

et tous ses modèles

und seine modelle

y todos sus modelos

sono conformi alle Direttive del Consiglio Europeo sottoelencate:

are in conformity with the requirements of the European Council Directives listed below:

sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:

der nachstehend angeführten Direktiven des Europäischen Rats:

cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:

89/336/EEC EMC Directive

92/31/EEC, 93/68/EEC

emendamenti successivi

and further amendments

et ses successifs amendements

und späteren Abänderungen

y succesivas enmiendas

Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei prodotti.

On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety.

Basée sur la législation des Etates membres relative à la compatibilité électromagnétique et à la sécurité des produits.

Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit und Produktsicherheit

entsprechen.

Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y las Medidas

de seguridad relativas al producto.

Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:

This declaration is based upon compliance of the products to the following standards:

Cette déclaration repose sur la conformité des produits aux normes suivantes:

Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:

Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:

EN 55022, August 1994

: L

IMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE CHARACTERISTICS OF INFORMATION

TECHNOLOGY EQUIPMENT

(ITE)

EN 61000-6-2, April 1999

: E

LECTROMAGNETIC COMPATIBILITY

(EMC).

ART

6-2: G

ENERIC

TANDARDS

- I

MMUNITY FOR INDUSTRIAL ENVIRONMENTS

Lippo di Calderara, 30/04/2004

Ruggero Cacioppo

Quality Assurance Supervisor

821000953 (Rev. C)

Autres manuels Datalogic Lecteur de codes-barres

Datalogic

Datalogic DS6300 Manuel utilisateur

Datalogic

Datalogic Gryphon GFS4 series Manuel utilisateur

Datalogic

Datalogic Gryphon 2D Series Manuel d'installation et d'exploitation

Datalogic

Datalogic MAGELLAN 3200VSI Manuel d'installation et d'exploitation

Datalogic

Datalogic Heron D110 Manuel utilisateur

Datalogic

Datalogic Gryphon D432 Manuel utilisateur

Datalogic

Datalogic GRYPHON BT SH3500 Manuel utilisateur

Datalogic

Datalogic PowerScan M8300 Manuel utilisateur

Datalogic

Datalogic DS4600A Manuel utilisateur

Datalogic

Datalogic QuickScan i QD2100 Manuel d'installation et d'exploitation

Datalogic

Datalogic Gryphon I GD441 Series Manuel utilisateur

Datalogic

Datalogic Gryphon GD4200 Manuel utilisateur

Datalogic

Datalogic PowerScan M8500 Manuel d'installation et d'exploitation

Datalogic

Datalogic PowerScan PM9500 Manuel utilisateur

Datalogic

Datalogic Gryphon I GBT4400 Manuel utilisateur

Datalogic

Datalogic QuickScan QBT24XX Manuel utilisateur

Datalogic

Datalogic DS6300 Manuel utilisateur

Datalogic

Datalogic QuickScan Lite QW2400 Manuel utilisateur

Datalogic

Datalogic QuickScan i Manuel d'installation et d'exploitation

Datalogic

Datalogic QuickScan QBT24 series Manuel d'installation et d'exploitation

Datalogic

Datalogic QuickScan QS6500 Manuel d'installation et d'exploitation

Datalogic

Datalogic Gryphon GFE4400 Guide de configuration rapide

Datalogic

Datalogic PowerScan D8530 Manuel utilisateur

Datalogic

Datalogic Touch 90 pro Manuel d'installation et d'exploitation

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur

Atid

Atid AT188N Plus Manuel utilisateur