Data Video DAC-10 Manuel utilisateur

1.AUDIO ENCODE Encode analog audio to DV with your choice of 12 bit/32Khz or

16bit/48Khz. 12 Bit/32khz is suggested for most DV Camcorders.

16bit/48Khz is suggested for DVD and DV Capture cards.

2. DV INPUT This switch will turn red when you press it. When it is red, the DV input is

enabled. When another input is enabled this switch will turn green.

3. ANALOG YUV VIDEO

INPUT

This switch will turn red when you press it. When it is red, the Analog

YUV video input is enabled. When another input is enabled this switch

will turn green.

4. ANALOG S (Y/C)

VIDEO INPUT

This switch will turn red when you press it. When it is red, the Analog

S(Y/C)video input is enabled When another input is enabled this switch

will turn green.

5. ANALOG COMPOSITE

VIDEO INPUT

This switch will turn red when you press it. When it is red, the Analog

Composite video input is enabled When another input is enabled this

switch will turn green.

6. COLOR PROCESSOR This control will adjust the color of both analog or DV input sources.

Press the knob to select Contrast, color or tint (NTSC only).

Rotate the knob to change the amount.

Note: Press the knob and hold for two seconds for resetting all

adjustments back to default (unity) setting

7. AUDIO LEVEL

INDICATORS

These meters show the audio INPUT level from the incoming source

8. AUDIO INPUT LEVEL

CALIBRATION

Turn these knobs to adjust the Audio OUTPUT level of the DAC-10.

Adjust the audio level controls for each left (channel one) and right

(channel 2) to let level LED’s indicating in between yellow (0dB) and

first red LED (+4dB).

1. POWER ON/OFF SWITCH

Turns main power on or off

2. POWER INPUT JACK

Connects to the supplied 12VDC 10 watt power supply

3. COMPONENT Y.U.V. VIDEO INPUT JACKS

Input for Y.U.V. component video from Betacam, DVCPro, DVCam, some DVD players, etc.

4. AUDIO/VIDEO INPUT JACK

Analog Audio/Video input convert to DV output.

Note: You can hook up all the cables onto all video/audio input connectors at same time without

conflicting to each connection

5. AUDIO/VIDEO OUTPUT JACKS

Analog Audio/Video signal output which is converted from DV input.

Note: You can hook up all the cables onto all video/audio output connectors at same time without

conflicting to each connection

6. DV IN/OUT JACKS (Two)

6 pin DV (FireWire, iLink, IEEE 1394) cable, from the DV port of a camcorder, DV Bank,

DV deck, etc.

7. DIP SWITCH MODE SETTING

Please refer to next page the DIP Switch setting.

8. BLACK BURST SIGNAL OUTPUT

Video Black Burst Signal to be used as a sync reference source

9. COMPONENT Y.U.V. OUTPUT JACKS

PLA Mode: Comply to SMPTE spec

NTSC Mode: Comply to Sony Betacam spec

Dip Switch Setting for Mode Select:

*. Note1᧶Mode DIP switch (Reboot the DAC-10 if you change a DIP Switch)

S1. PAL or NTSC (PAL-ON, NTSC-OFF)

S2. 7.5 IRE / 0 IRE (0 IRE-ON, 7.5 IRE-OFF). (NTSC mode only)

*. Note2: 0 IRE is most often used in Japan. 7.5 IRE is used elsewhere.

S3. Locked Audio Mode

S3 -- OFF: Locked Audio

S3 – ON: Unlocked Audio

S4 & S5 for NTSC and PAL video system

*. Please refer to next page for more detail information

S6. Factory setting (OFF), please do not change.

*. Note3: Turn-on the DAC-10 before launching any editing software.

*. Note4: To work with a MAC with Final Cut Pro:

1). Select "Preferences" from Final Cut Pro menu

2). Select "General" page

3). Uncheck "Abort capture on dropped frame"

4). Uncheck "Abort capture on time code break" for Final cut pro 3.0

5). Click OK button

ON MAC OS

S5 ON S4 OFF Windows 2000 and Windows 98

ON Windows XP and Windows ME

S5 OFF S4 OFF Camera

Dip Switch Setting to work with Windows & MAC Operation system

The DAC-10 has dip switches 4 and 5 that control the clocking frequency when it is converting video,

if the dip switches are not configured for your operating system or type of device, a loss in video can

occur. Please refer to dip switch chart below and make sure that your DAC-10 is setup correctly.

NTSC System (USA)

MAC OS

NTSC System (USA)

Windows XP and Windows ME

NTSC System (USA)

Windows 2000 and Windows 98

NTSC System (USA)

Camera

PAL System (USA)

MAC OS

PAL System (USA)

Windows XP and Windows ME

PAL System (USA)

Windows 2000 and Windows 98

PAL System (USA)

Camera

Operation Procedure:

Step_1. Select the desired mode by setting the dip switches. Reboot the DAC-10 after changing

the dip switches

Step_2. Install the equipment as shown in installation diagrams

Step_3. Ensure that all equipment is turned on

Step_4. Select the video source. If the video source is analog, select the desired audio sampling Rate

Step_5. Playback the source video

Step_6. If needed, calibrate the playback video and audio output level

Step_7. To generate an analog Color Bar output, under the DV mode, press on the “16 BIT” key. The

Color Bar will output from YUV,S(Y/C) and Composite video jacks at the same time. Press on the “16 BIT”

key again back to normal operation.

INPUTS SPECIFICATION

S-VHS Video Source

Composite Video Sources

Component YUV Video

DV (iLink)Source

Y/C in: 4--pin 75 ohm DIN connector

1.0 Vp-p 75 ohm BNC connector

Betacam standard,Y, R-Y, B-y 75 ohm BNC connectors

Data Transfer Rate 25Mbps,

PAL: 4:2:0 NTSC: 4:1:1

Outputs

S-VHS Video Source

Composite Video Source

Component YUV Video

Black Burst Video

Video Frequency Response

(DV input)

Differential Gain

Differential Phase

Video S/N Ratio

Decoder(DVIn)

Encoder (A/V In)

Audio Sampling Rate

Audio Level

Audio THD

Audio Frequency Response

Audio S/N Ratio

Y/C out 4-pin 75 ohm DIN connector

1.0 Vp-p 75 ohm BNC connector

Betacam standard, Y, R-Y, B-y 75 ohm BNC connectors

75 ohm BNC connector

5.0 MHz +/- 3 dB

+/- 3 %

>50dB

>48dB

12 bit/32KHz and 16bit/48KHz optional

Unity +/- 1.0dB

<0.5%

20 ~ 20KHz +/- 3dB

>65dB

GENERAL

Power Input

Ambient Temperature

Ambient Humidity

Dimensions

Weight

Accessories

DC 12V 1.0A AC Adaptor (included)

32o~130

o F(0

o~55

o C)

Less than 90 %

210 (W) x 240 (D) x 88(H) mm (without rubber feet)

8.3"(W) x 9.45"(D) x 3.5" (H) (without rubber feet)

1.8 Kg/4.0lbs

BNC, S-Video and DV cables (included)

Service and Support

It is our goal to make your products ownership a satisfying experience. Our supporting staff

is available to assist you in setting up and operating your system. Please refer to our web site

www.datavideo-tek.com for answers to common questions, support requests or contact your

local office below.

Datavideo Corporation (USA)

12300-U East Washington Blvd., Whittier, CA 90606 USA

Tel: +1 562 696 2324 www.datavideo.us

Datavideo Technologies Europe BV

Californiedreef 263565 BL Utrecht, The Netherlands

Tel: +31 30 261 9656 www.datavideo.info

Datavideo UK Limited

Unit 2 Waterside Business Park, Hadfield, Glossop, Derbyshire SK131BE UK

Tel: +44 1457 851000 www.datavideo.info

Datavideo Technologies Co., Ltd.

10F, 176 Jian-Yi Rd, Chung Ho City, Taipei Hsien, Taiwan 235

Tel: +886 2 8227 2888 www.datavideo.com.tw

Datavideo Technologies China Co.

2F-D, 2 Lane 777, West Guangzhong Rd, Zhabei District, Shanghai, China

Tel: +86 21 5603 6599 www.datavideo.cn

Datavideo Technologies (S) PTE Ltd.

100 Lor 23, Geylang Rd, #01-03 D’Centennial, Singapore 388398

Tel: +65 6749 6866 www.datavideo.sg

All the trademarks are the properties of their respective owners.

P/N: 082060351E2

Autres manuels pour DAC-10

Table des matières

Autres manuels Data Video Changer

Data Video

Data Video SE-700 Manuel utilisateur

Data Video

Data Video SE-3000 Manuel utilisateur

Data Video

Data Video FS-30 Manuel utilisateur

Data Video

Data Video SE-2850 Manuel utilisateur

Data Video

Data Video HS-1500T Manuel utilisateur

Data Video

Data Video SE-500 Manuel utilisateur

Data Video

Data Video SE-2200 Manuel utilisateur

Data Video

Data Video SE-2800 Manuel utilisateur

Data Video

Data Video DAC-200 Manuel utilisateur

Data Video

Data Video SE-2850 Manuel utilisateur

Data Video

Data Video SE-3000 Manuel utilisateur

Data Video

Data Video SE-2000R Manuel utilisateur

Data Video

Data Video RP-54 Manuel utilisateur

Data Video

Data Video SEB-1200 Manuel utilisateur

Data Video

Data Video SE-500HD Manuel utilisateur

Data Video

Data Video RMC-120 Manuel utilisateur

Data Video

Data Video OBV-2850 Manuel utilisateur

Data Video

Data Video SE-2800 Manuel utilisateur

Data Video

Data Video SE-500 Manuel utilisateur

Data Video

Data Video SE-650 Manuel utilisateur

Data Video

Data Video SE-700 Manuel utilisateur

Data Video

Data Video HS-500 Manuel utilisateur

Data Video

Data Video SE-600 Manuel utilisateur

Data Video

Data Video SE-2800 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur