Danfoss C37 Manuel utilisateur
C37
C37
VI.7C.E6.02
2005.09
VI.7C.E6.02
2005.09
www.danfoss.com
User's Guide
Installer's Guide
www.danfoss.com
ECL Comfort
Installer's Guide
ECL Comfort
User's Guide
*087R8070*
*VI7CE602*
*087R8070*
*VI7CE602*
Mixing controller with ON / OFF
controlled DHW charging
The shown diagram is a fundamental and simplified example and
does not contain all components that are necessary in a system.
If the system you are about to install differs from the shown
diagram of a standard heating system, feel free to sketch an outline
for comparison. Adaptation of systems, see section 10.
List of components:
ECL Comfort 300
S1 Outdoor temperature sensor
S2 Room temperature sensor, circuit I
S3 Flow temperature sensor, circuit I
S4 Return temperature sensor
S5 DHW tank temperature sensor, lower
S6 DHW tank temperature sensor, upper
P1 Circulation pump, heating, circuit I
P2 Primary charging pump, DHW, circuit II
P3 Charging / circulation pump, DHW, circuit II
M1 Motorized control valve, heating, circuit I
Circuit
indicator
Circuit
selector
Shift
button
Adjust-
ment
Controller
mode
Controller mode
Manual operation (used only at maintenance
and service)
Scheduled operation
Constant comfort temperature
Constant setback temperature
Standby mode
Arrow buttons. Switch between the lines of the ECL
Card.
Shift button. Switches between temperatures,
changeover points etc.
Adjust temperatures and values etc.
Circuit selector for switching between the circuits.
Safety Note
To avoid injury of persons and damages to the device, it is
absolutely necessary to read and observe these instructions
carefully.
Necessary assembly, start-up, and maintenance work must be
performed by qualified and authorized personnel only.
This guide is associated with ECL Card 087B4758
Installer:
By:
Date:
Table of Contents
Sections in the Installer’s Guide
The documentation for the ECL Comfort controller is
composed of numbered sections. Only sections relevant to
your ECL Comfort controller are included here.
Before you start
Installation
10 Identifying the system type
11 Mounting the ECL Comfort controller
12 Electrical connections 230 V a.c.
14 Connecting and placing the temperature sensors
15 Inserting the ECL Card
Basic Set-up
16 Adjusting the ECL Card settings
17 Setting the time and date - line A
18 Monitoring temperatures and system units - line B
19 Manual control - line B
20 Setting the heat curve - line C
21 Heating cut-out - line 1
22 Flow temperature limits - line 2
23 Room temperature influence - line 3
26 Control parameters - lines 4-7
27 Cut-in and cut-out temperature at DHW charging
- lines 1-2, circuit II
Control & Overviews
29 Check list
30 ECL Card settings
31 Service parameters
Extended Service
32 Adjusting the service parameters
Miscellaneous
34 Copying with the ECL Card
User's Guide (turn the guide over for sections 1-7)
1 Choose your favorite display
2 Select circuit mode
3 Set your room and DHW charging temperature
4 Set your personal schedule
5 Advantages of the ECL Card
6 Hot points
7 Definitions
VI.7C.E6.02
Card C37
2005.09
Sketch your application
The ECL Comfort controller series is designed for a wide
range of heating, hot-water and cooling systems with
different configurations and capacities.
If your system differs from the diagrams shown in section
10, you may want to make a sketch of the system about to
be installed. This makes it easier to use the Installer’s Guide,
which will guide you step-by-step from installation to final
adjustments before the end-user takes over.
The controller is pre-programmed with factory settings that are
shown in the relevant sections of this guide.
However, you might come across some settings that are not listed
in this instruction. These settings could be related either to recent
updates or the use of optional modules (which are described in
the instructions in question).
How to use this guide
This guide is divided into two parts:
• User’s Guide: Yellow sections 1-7
• Installer's Guide: Grey sections 10 and onwards
The application C37 is very flexible. These are the basic
principles:
Heating:
Typically, the flow temperature is always adjusted according to
your requirements.
The flow temperature sensor (S3) is the most important sensor.
The desired flow temperature at S3 is calculated in the ECL
controller, based on the outdoor temperature (S1). The lower the
outdoor temperature, the higher the desired flow temperature.
The motorized control valve (M1) is opened gradually when the
flow temperature is lower than the desired flow temperature and
vice versa.
The return temperature (S4) to the district heating supply should
not be too high. If so, the desired flow temperature can be
adjusted (typically to a lower value), thus resulting in a gradual
closing of the motorized control valve. In boiler-based heating
supply the return temperature should not be too low (same
adjustment procedure as above).
If the measured room temperature does not equal the desired
room temperature, the desired flow temperature can be adjusted.
DHW:
If the measured DHW temperature is lower than the desired DHW
heating temperature minus the cut-in difference, the desired flow
temperature at S3 is increased in order to heat the DHW. DHW
heating can have priority, i.e. pump P2 is ON and pump P1 is OFF
(or changeover valve is activated and P1 is still ON).
Before you start
Installation
The ECL Comfort controller is a universal controller that can
be used for various systems. Based on the shown standard
systems, it is possible to configure additional systems.
In this section you find the most frequently used systems. If
your system is not quite as shown below, find the diagram
which has the best resemblance with your system and make
your own combinations.
The functions can only be realized with ECL Comfort 300 and as of
controller version 1.08.
10.1 Indirectly connected system and secondarily
connected DHW storage charging system
System settings
Circuit Line Description Recomm.
setting
I 51 DHW charging pump /
changeover valve OFF
I 52 Closed valve / normal operation OFF
I 53 Desired flow temperature at
DHW charging OFF
I 90 P3 = DHW circulation pump OFF
System diagrams in this instruction are principal drawings and do
not contain all components which are necessary in your systems.
Identifying the system type
10a
Installation
10.2 Indirectly connected system and secondarily
connected DHW storage charging system
(DHW priority)
System settings
Circuit Line Description Recomm.
setting
I 51 DHW charging pump /
changeover valve ON
I 52 Closed valve / normal operation OFF
I 53 Desired flow temperature at
DHW charging OFF
I 90 P3 = DHW circulation pump OFF
P2/M2*
For the control of the actuator use either relay output P2 or triac
output M2, see section 12.
10.3 Indirectly connected system and secondarily
connected DHW storage tank with built-in
heating coil
System settings
Circuit Line Description Recomm.
setting
I 51 DHW charging pump /
changeover valve OFF
I 52 Closed valve / normal operation OFF
I 53 Desired flow temperature at
DHW charging OFF
I 90 P3 = DHW circulation pump ON
10b
Installation
10.4 Indirectly connected system and secondarily
connected DHW storage tank with built-in
heating coil (DHW priority)
System settings
Circuit Line Description Recomm.
setting
I 51 DHW charging pump /
changeover valve ON
I 52 Closed valve / normal operation OFF
I 53 Desired flow temperature at
DHW charging OFF
I 90 P3 = DHW circulation pump ON
P2/M2*
For the control of the actuator use either relay output P2 or triac
output M2, see section 12.
10.5 Indirectly connected system and primarily
connected DHW storage tank with built-in
heating coil
System settings
Circuit Line Description Recomm.
setting
I 51 DHW charging pump /
changeover valve ON
I 52 Closed valve / normal operation OFF
I 53 Desired flow temperature at
DHW charging ON
I 90 P3 = DHW circulation pump ON
P2/M2*
For the control of the actuator use either relay output P2 or triac
output M2, see section 12.
10c
Installation
The following heating systems are only applicable with relay
module ECA 80
10.6 Indirectly connected system and secondarily
connected DHW storage charging system
System settings
Circuit Line Description Recomm.
setting
I 51 DHW charging pump /
changeover valve OFF
I 52 Closed valve / normal operation OFF
I 53 Desired flow temperature at
DHW charging OFF
I 90 P3 = DHW circulation pump ON
10.7 Indirectly connected system and secondarily
connected DHW storage charging system
(DHW priority)
System settings
Circuit Line Description Recomm.
setting
I 51 DHW charging pump /
changeover valve ON
I 52 Closed valve / normal operation OFF
I 53 Desired flow temperature at
DHW charging OFF
I 90 P3 = DHW circulation pump ON
P2/M2*
For the control of the actuator use either relay output P2 or triac
output M2, see section 12.
10d
Installation
For easy access, you should mount the ECL Comfort
controller near the system. Select one of the three
following methods:
• Mounting on a wall
• Mounting on a DIN rail
• Mounting in a panel
Screws and rawlplugs are not supplied.
Mounting on a wall
Socket for mounting on wall: Order code No. 087B1149.
Mount the terminal box on a wall with a smooth surface.
Establish the electrical connections and position the
controller in the box. Secure the controller with the fixing
screw.
Mounting on a DIN rail
Mounting kit: Order code No. 087B1145.
A mounting kit is necessary to mount the box with the
controller on a DIN rail.
Mounting in a panel
Connector set: Order code No. 087B1148.
The panel plate thickness must not exceed 3 mm.
Prepare a cut-out with the dimensions 93 x 139 mm. Pull off
the right side of the lid by means of a screwdriver.
Insert the controller into the panel cut-out and fix it with the
two locks which are placed diagonally in two corners of the
controller.
Mounting the ECL Comfort
controller
11a
Table des matières
Autres manuels Danfoss Thermostat
Danfoss
Danfoss RET B-LS Manuel utilisateur
Danfoss
Danfoss TP7001 series Manuel utilisateur
Danfoss
Danfoss Eco Manuel utilisateur
Danfoss
Danfoss ECtemp Touch Manuel utilisateur
Danfoss
Danfoss TP75H Manuel d'utilisation
Danfoss
Danfoss RET230P Manuel utilisateur
Danfoss
Danfoss SET 3E Manuel utilisateur
Danfoss
Danfoss RET2001 Manuel utilisateur
Danfoss
Danfoss living connect Z Manuel utilisateur
Danfoss
Danfoss Living Eco Manuel utilisateur
Danfoss
Danfoss GET B-RF Mode d’emploi
Danfoss
Danfoss EFIT 550 Manuel utilisateur
Danfoss
Danfoss TP4000 Range Manuel utilisateur
Danfoss
Danfoss ECL Comfort 310, P314 Manuel utilisateur
Danfoss
Danfoss SET 3E Manuel utilisateur
Danfoss
Danfoss DEVI DEVIreg 330 Manuel utilisateur
Danfoss
Danfoss TP4 Mode d'emploi
Danfoss
Danfoss TP5001 series Manuel utilisateur
Danfoss
Danfoss MBC 8000 Manuel utilisateur
Danfoss
Danfoss TP9 Manuel utilisateur
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
