Danfoss SonoSafe Manuel d'utilisation

09/2017 © Danfoss VUIGB802

www.heating.danfoss.com

Installation & User Guide

SonoSelect and SonoSafe

Energy Meters

2 | © Danfoss | Energy Meters | 2018.01 VUIGB802

Installation & User Guide SonoSelect and SonoSafe

Date

Issued by

Place of issue

Date

Approved by

2017.08.08

Nordborg, DK

Søren Nielsen

R&D Director, Danfoss Energy Metering

2017.08.08

Bjarne Halkjær

Strategy & portfolio Director

Danfoss only vouches for the correctness of the English version of this declaration. In the event of the declaration being translated into

any other language, the translator concerned shall be liable for the correctness of the translation

ID No: 014R2903

Revision No: 10

Page 1 of 1

Da nf os s A/ S

-6430 Nordborg

nmark

CVR nr.: 20 16 57 15

Teleph

one: +45 7488 2222

Fax:

+45 7449 0949

EU DECLARATION OF CONFORMITY

Danfoss A/S

Danfoss Energy Metering

declares under our sole responsibility that the

Product(s):

Energy Meters

Type(s):

SonoSelect 10 and SonoSafe 10

covered by this declaration is in conformity with the following directive(s), standard(s) or other normative

document(s), provided that the product is used in accordance with our instructions.

�MID Directive 2014/32/EU Measuring Instrument Directive

Module B +D

oEN1434-4:2015

Notified Body: Force Certification, 0200, performed type approval and issued certificate DK-0200-MI004-034

�EMC Directive 2014/30/EU Electromagnetic Compatibility1

oEN 61000-6-1:2007

oEN 61000-6-3:2007/A1:2011

�RoHS Directive 2011/65/EU Restriction of Hazardous substances

oEN 50581:2012

�RED Directive 2014/53/EU Radio Equipment Directive2

oEN 300 220-2 V3.1.1

oEN 301 489-1 V1.9.2:2011-09

oEN 301 489-3 V1.6.1:2013-06

oEN 62311:2008

oEN 61010-1:2010

oEN 60950-1:2006/A11:2009/A1:2010/A12:2011/AC:2011/A2:2013

Notified Body: Eurofins GmbH, 0681, performed type approval and issued certificate G0M-1608-5835-V01

�LVD Directive 2014/35/EU Low Voltage Directive1

oEN 62311:2008

oEN 61010-1:2010

oEN 60950-1:2006/A11:2009/A1:2010/A12:2011/AC:2011/A2:2013

1For variants with Radio Module the declaration for EMC & LVD shall be ignored

2For variants without Radio Module the declaration for RED shall be ignored

Note: To ensure latest version of declaration, please visit danfoss.com.

VUIGB802 © Danfoss | Energy Meters | 2018.01 | 3

Installation & User Guide SonoSelect and SonoSafe

Contents

1. General ................................................................................. 4

1.1 Inside the box ........................................................................4

2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.1 Preparation...........................................................................4

2.2 Identification of installation: Supply/Return pipe installation ...........................5

2.3 Flow sensor installation ...............................................................5

2.4 Mounting orientation, calculator ......................................................5

2.5 Mounting of O-ring and temperature sensor ..........................................6

2.6 Communication (Expansion modules).................................................7

2.7 Installation of module/cable ........................................................ 10

2.8 Battery ..............................................................................11

3. Commissioning ......................................................................... 12

3.1 Bleeding ........................................................................... 12

3.2 Supply/return configuration .........................................................12

3.3 Meter sealing....................................................................... 12

3.4 IP class ............................................................................. 12

4. Function overview ...................................................................... 13

4.1 Menu structure ..................................................................... 13

4.2 Display explanation..................................................................14

4.3 Alarms ..............................................................................14

5. Device overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

6. Disposal................................................................................ 15

4 | © Danfoss | Energy Meters | 2018.01 VUIGB802

Installation & User Guide SonoSelect and SonoSafe

1. General

Ambient operating temperature class A 5 - 55 °C (Indoor installation, non-condensing)

Ambient storage temperature -25 - 60 °C

Temperature media 5 - 95 °C

Mechanical environment class M2

Electromagnetic environment class E1

Pressure PN16

MID Accuracy Class 2

1.1 Inside the box

Description of components included in the box

107/2015 ©Danfoss VDIGH102

InstallationGuide

SonoSelect and SonoSafe

energy meters

1 x

Energy meter

2 x Gaskets &

1 temperature

sensor O-ring

4 x

Wired seals

1 x

Installation

& User Guide

Note: For cooling meters a wall mounting kit is delivered with the product

2. Installation

2.1 Preparation

SonoSelect incorporates a tamper monitoring function. If the

calculator is opened the meter will set alarm E13 in display.

Don’t open unless for adding communication module,

replacing battery or installing cables.

Reset requires Bluetooth dongle 014U1963 and SonoApp

service tool.

SonoSelect is delivered with the option of reconfiguring

supply/return using the Bluetooth dongle 014U1963 and

SonoApp service tool.

Note:

• Product is approved for ambient temperature between 5-55 °C, non-condensing (indoor installation). It is recommended

to install Calculator at max. 45 °C to secure optimal conditions for battery lifetime. At media temperatures below ambient

temperature (cooling) the calculator must be mounted separately from the flow sensor to prevent condensation.

• Avoid installation stress from pipes and fittings.

• Flush the system.

VUIGB802 © Danfoss | Energy Meters | 2018.01 | 5

Installation & User Guide SonoSelect and SonoSafe

2.2 Identification of installation: Supply/Return pipe installation

Supply installation Return installation

Note: Heat meters have red temp sensor in supply pipe and all cooling meters have blue temp sensor in supply pipe

2.3 Flow sensor installation

Pipe position: No limitations but avoid positions where air

can be collected.

Rotation in pipe axis: Flow sensor should be angled in 45

to 315° to avoid air collection in flow sensor.

2.4 Mounting orientation, calculator

4 x 90°

Click!

1a.

1b.

6 | © Danfoss | Energy Meters | 2018.01 VUIGB802

Installation & User Guide SonoSelect and SonoSafe

2.5 Mounting of O-ring and temperature sensor

One temperature sensor is factory mounted in the flow sensor. The other must be mounted in the

opposite pipe relative to the flow sensor installation. Mounting pin available as accessory.

Mount O-ring on

pin.

Insert pin with

O-ring.

Position O-ring.

Remove pin.

Moist and insert sensor

probe. Tighten at torque

12 ± 2 Nm.

To ensure accuracy and a tight seal the sensor installation should comply to EN1434-2 annex A:

Key

Threaded

connection size A

Tapping bore

size B

G½ 18.5 mm

G¾ 24 mm

G1 30.5 mm

G1¼ 39mm

Note:

• Tolerance on machined dimensions = ± 0.5 mm.

• Pipe fittings for use with probe type DS (Direct Short).

: provision for security sealing.

VUIGB802 © Danfoss | Energy Meters | 2018.01 | 7

Installation & User Guide SonoSelect and SonoSafe

2.6 Communication modules

Modules in general

To adapt the meter for various applications SonoSelect 10 and SonoSafe 10 features a slot for mounting

communication modules.

Each module features its own µ-controller and is powered by its own battery.

Modules have their own parameter set which is saved in the module µ-controller flash memory. A local

copy of the energy meter parameters used for communication is stored in the module.

Data from module is updated in meter every 10 minutes.

Power: Lithium Thionyl Chloride battery (half of AA size).

2 pulse in/outputs have common ground.

Modules are galvanically isolated from main Energy Meter circuitry

Wired M-Bus module with 2 pulse inputs

Once installed the meter will display the icon for wired communication and pulse inputs in loop 2 of the

display.

Wired M-Bus is galvanically isolated from µ-controller and pulse inputs.

The two pulse inputs can be programmed independently of each other (see specification for pulse input

module).

M-Bus (primary) Lithium Thionyl Chloride battery (half of AA size)

M-Bus (secondary) M-Bus supply

Baud rate supported 300, 2400, 4800, 9600

Communication protocol According to EN1434-3 & EN13757-3

Battery life time 16+1 year

Addressing Serial number: sssssvvNNyyWW

ss: Primary address, yWWsssss: Secondary address

Wireless OMS communication module, 868.95MHz with 2 pulse inputs

Once installed the meter will display the icon for wireless communication and pulse inputs in loop 2 of

the display. The two pulse inputs can be programmed independently of each other (see specification for

pulse input module).

Standard Open Metering System (OMS) issue 4.0.2

Frequency 868.95 MHz

Antenna Internal

Transmission power 10mW (Max. 25mW; 13,9 dBm)

Mode T1 mode

Encryption AES 128 bit encryption (mode 5), Parameterized Static key

Sending interval Fixed network: 15 min.

Telegram Standard telegram*

Battery life time 16+1 year (with pulse inputs off)

Addressing Serial number: sssssvvNNyyWW

yWWsssss: Secondary address

* See section with data telegram.

8 | © Danfoss | Energy Meters | 2018.01 VUIGB802

Installation & User Guide SonoSelect and SonoSafe

2 pulse input module

Once installed the meter will display the icon for pulse inputs in menu 2 of the display. Accumulated

volume is only readable by communication. The two pulse inputs can be programmed independently of

each other.

Pulse value 0.001 m³ to 1 m³ per pulse

Voltage supply ≤ 6.0 V

Source current ≤ 0.1 mA

High level input threshold ≥ 2 V

Low level input threshold ≤ 0.5 V

Pull-up resistor 100 kΩ

Pulse length ≥100 ms

Maximum frequency ≤ 5 Hz

Pulse inputs According to EN1434-2, section 7.1.5 (Classification of pulse input devices Class IB)

Battery life time 16+1 year

* Suitable for both electronic switch and Reed contact.

2 pulse output module

Once installed the meter will display the icon for wired communication in menu 2 of the display.

Pulse 1 (energy*) + terminal 16, - terminal 17

Pulse 2 (volume*) + terminal 18, - terminal 19

Pulse value* Unit follow the display. Scaling follow least significant digit of the display

(default setting can be changed via SonoApp)

Pulse timing Updates every 15 seconds

Polarity reversal: Not possible, but can withstand -30V, max 27 mA without damage

Pulse length ≥100 ms

Pulse Pause: ≥100 ms

Voltage supply 3-30 V

Source current ≤ 27 mA

“ON” condition U<2,0 @ 27mA

“OFF” condition R>=6 MΩ

Maximum frequency ≤ 5 Hz

Pulse outputs According to EN1434-2, section 8.2.3

(Classification of pulse output devices Class OB)

Battery life time 16+1 year

Cable length Max 25 m

Alarms

E32 activates in meter if:

1) Module battery is empty

2) When no. of delayed pulses exceeds 5000 (incorrect scaling)

*Default setting. Can be changed via SonoApp.

VUIGB802 © Danfoss | Energy Meters | 2018.01 | 9

Installation & User Guide SonoSelect and SonoSafe

Data telegram

Wired M-bus

Standard telegram:

• Accumulated energy

• Accumulated volume

• Current flow

• Current power

• Supply temperature

• Return temperature

• Difference temperature

• Enclosure temperature

• Current time

• Hour counter factory

• Hour counter OK

Wireless M-bus (OMS)

Standard telegram fixed network

(15 minutes sending interval):

• Accumulated energy

• Accumulated volume

• Current flow

• Current power

• SupplyTemperature

• ReturnTemperature

• CurrentTime

Wireless M-Bus (Walk -by)

Standard telegram Walk by

(2 minutes sending interval):

• Accumulated energy

• Accumulated volume

• CurrentTime

• Hour counter factory

• Month log 1 (last month log)

*Can be changed via SonoApp

Terminals and cables

Communication Name Terminal No.

M-Bus Meter bus (blue or orange) 24

Meter bus (blue or orange) 25

Pulse input

Pulse input 1 + (brown) 50

Pulse input 1 - (white) 51

Pulse input 2 + (brown) 52

Pulse input 2 - (white) 53

Pulse output

Pulse output 1+ (brown) 16

Pulse output 1- (white) 17

Pulse output 2+ (brown) 18

Pulse output 2 – (white) 19

Name Lenght

Cable specification

Pulse input cables 22AWG <10m

Pulse output cables 22AWG <25m

To ensure IP protection class connecting cable

outerjackets must be Ø4.2 ± 0.1 mm

Communication cables delivered with heat meter.

Cable ends are stripped with crimped ferule. 1.0m

10 | © Danfoss | Energy Meters | 2018.01 VUIGB802

Installation & User Guide SonoSelect and SonoSafe

2.7 Installation of module/cable

Before handling module PCB ensure relevant ESD regulations are

observed (IEC 61340-5-1).

Break wired seal for enclosure.

Cut rubber parallel to enclosure.

Insert module following guide on PCBA cover.

Insert cable through hole, connect cable and fix to screw terminals

matching color and terminal numbers.

Fix cable(s) to cable relief. Outer jacket no longer than 9 mm from cable

relief (line). Press down.

Close enclosure making sure that no cables interfere with rubber

sealing and other internal parts.

Click!

Reset tamper alarm via Sono-App for SonoSelect 10.

For module configuration, see SonoApp user guide.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Danfoss Instrument de mesure

Danfoss

Danfoss Vickers Target-Pro 2 Manuel utilisateur

Danfoss

Danfoss SonoMeter 30 Manuel utilisateur

Danfoss

Danfoss AK-EM 100 Manuel utilisateur

Danfoss

Danfoss SonoMeter 30 Manuel utilisateur

Danfoss

Danfoss ADAP-KOOL AK-LM 340 Manuel utilisateur

Danfoss

Danfoss AK-LM 350 Mode d’emploi

Danfoss

Danfoss Supercal 5 Manuel utilisateur

Danfoss

Danfoss SonoSelect 10 Manuel d'utilisation

Danfoss

Danfoss RAVK 10-30 Manuel utilisateur

Danfoss

Danfoss EKC 201 Manuel utilisateur

Danfoss

Danfoss PFM 100 Manuel utilisateur

Danfoss

Danfoss SonoMeter 30 Manuel utilisateur

Danfoss

Danfoss Infocal 9 Manuel d'utilisation

Danfoss

Danfoss PFM 5001 Manuel utilisateur

Danfoss

Danfoss SonoSelect Manuel utilisateur

Danfoss

Danfoss AK-LM 330 Mode d’emploi

Danfoss

Danfoss AKS 4100 Manuel utilisateur

Danfoss

Danfoss MES 1003 Manuel utilisateur

Danfoss

Danfoss VLT Manuel utilisateur

Danfoss

Danfoss PR-OCTO Manuel utilisateur

Danfoss

Danfoss MCH19AM1649 Manuel

Danfoss

Danfoss AK-SM 350 Manuel utilisateur

Danfoss

Danfoss SonoSensor 30 Manuel d'utilisation

Danfoss

Danfoss PR-SC4K Direct Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur