Danfoss MCB 113 Manuel utilisateur

Operating Guide

VLT® Extended Relay Card MCB 113

VLT® HVAC Drive FC 102, VLT® Refrigeration

Drive FC 103, VLT® AQUA Drive FC 202, VLT® Au-

tomationDrive FC 301/FC 302

Contents

1 Introduction 5

1.1 Purpose of this Operating Guide 5

1.2 Trademarks 5

1.3 Document Version 5

1.4 Additional Resources 5

1.5 Product Overview 5

1.5.1 Intended Use 5

1.6 Type Approvals and Certifications 6

2 Safety 8

2.1 Safety Precautions 8

3 Installation 10

3.1 Mechanical Installation 10

3.1.1 Installation in Enclosure Sizes A5–C4 10

3.2 Electrical Installation 10

3.2.1 Safety Instructions 10

3.2.2 Wiring Schematic 11

3.2.3 Wiring Schematic - Following NAMUR 13

3.2.4 Galvanic Isolation 13

4 Parameter Setup 15

4.1 Introduction to Parameter Setup 15

4.2 5-** Digital In/Out 15

4.2.1 Parameter Group 5-1* Digital Inputs 15

4.2.2 Parameter Group 5-2* Digital Inputs 31

4.2.3 Parameter Group 5-3* Digital Outputs 32

4.2.4 Parameter Group 5-4* Relays 38

4.3 6-** Analog Outputs 43

4.3.1 6-7* Analog Output 3 MCB 113 43

4.3.2 6-8* Analog Output 4 MCB 113 45

4.4 14-** 24 V DC External Supply 46

4.4.1 14-8* Options 46

4.5 16-** Data Readouts 47

4.5.1 16-6* Inputs and Outputs 47

5 Specifications 50

5.1 Relays 50

5.2 Digital Inputs 50

5.3 Analog Outputs 50

ContentsOperating Guide | VLT® Extended Relay Card MCB 113

5.4 EMC 50

6 Appendix 51

6.1 Abbreviations 51

6.2 Conventions 51

ContentsOperating Guide | VLT® Extended Relay Card MCB 113

1 Introduction

1.1 Purpose of this Operating Guide

This Operating Guide provides information for safe installation and setup of a VLT® Extended Relay Card MCB 113 option used in the

VLT® FC drive series.

The Operating Guide is intended for use by qualified personnel only. Personnel must be familiar with the VLT® FC drive series.

Read and follow the instructions before installation and setup, and ensure that instructions for safe installation and setup are observed.

Always keep these instructions available with the drive.

1.2 Trademarks

VLT® is a registered trademark for Danfoss A/S.

1.3 Document Version

This operating guide is regularly reviewed and updated. All suggestions for improvement are welcome. See document version and

changes applied in table 1.

The original language of this manual is English.

Table 1: Version and Changes Applied

Document version Remarks

AQ322553864968, version 0101 Option now also applicable for VLT® HVAC Drive FC 102, VLT® Refrigeration Drive FC 103, and VLT®

AQUA Drive FC 202.

1.4 Additional Resources

More information resources are available to understand advanced drive functions and programming.

• The VLT® FC Series Operating Guides provide information required to install and commission the drive for given applications.

• The VLT® FC Series Programming Guides provide greater detail on working with parameters.

• VLT® FC Series Design Guides provide detailed capabilities and functionality to design motor control systems for various

applications.

Technical documentation for other product options is available at www.danfoss.com.

1.5 Product Overview

1.5.1 Intended Use

The VLT® Extended Relay Card MCB 113 is exclusively intended for use in option slot C1. The option is constructed as a standard C1

option compatible with the following VLT® FC Series:

Introduction

Operating Guide | VLT® Extended Relay Card MCB 113

AQ322553864968en-000101 / 130R0353| 5

• VLT® HVAC Drive FC 102

• VLT® Refrigeration Drive FC 103

• VLT® AQUA Drive FC 202

• VLT® AutomationDrive FC 301/FC 302.

The MCB 113 adds 7 digital inputs, 2 analog outputs, and 4 SPDT relays to the standard I/O of the drive. These additions make it

possible to comply with the German NAMUR NE37 recommendations.

When ordered with the drive, the option is installed from factory. For ordering, use the following order numbers:

• 130B1164 (Non-coated)

• 130B1264 (Coated)

For retrofit, a mounting kit must be purchased. The mounting kit includes a fan for VLT® Motion Control MCO 305 and is only to be

mounted if MCO 305 is used.

Table 2: Mounting Kits for Book-style Enclosures

Enclosure sizes Order number

A2 and A3 (40 mm for 1 C option) 130B7530

A2 and A3 (60 mm for C0 + C1 option) 130B7531

B3 (40 mm for 1 C option) 130B1413

B3 (60 mm for C0 + C1 option) 130B1414

Table 3: Mounting Kits for Compact Enclosures

Enclosure size Order number

A5 130B7532

B (except B3), C, D, E, and F 130B7533

1.6 Type Approvals and Certifications

The following list is a selection of possible type approvals and certifications for Danfoss drives:

089

Introduction

Operating Guide | VLT® Extended Relay Card MCB 113

AQ322553864968en-000101 / 130R0353

NOTICE

The specific approvals and certification for the drive are on the nameplate of the drive. For more information, contact the local

Danfoss office or partner.

Introduction

Operating Guide | VLT® Extended Relay Card MCB 113

AQ322553864968en-000101 / 130R0353| 7

2 Safety

2.1 Safety Precautions

WARNING

HIGH VOLTAGE

AC drives contain high voltage when connected to AC mains input, DC supply, or load sharing. Failure to perform installation,

start-up, and maintenance by qualified personnel can result in death or serious injury.

-Only qualified personnel must perform installation, start-up, and maintenance.

WARNING

UNINTENDED START

When the drive is connected to the AC mains, DC supply, or load sharing, the motor may start at any time, causing risk of death,

serious injury, and equipment or property damage. The motor may start by activation of an external switch, a fieldbus

command, an input reference signal from the LCP or LOP, via remote operation using MCT 10 Set-up software, or after a cleared

fault condition.

-Press [Off] on the LCP before programming parameters.

-Disconnect the drive from the mains whenever personal safety considerations make it necessary to avoid unintended

motor start.

-Check that the drive, motor, and any driven equipment are in operational readiness.

WARNING

DISCHARGE TIME

The drive contains DC-link capacitors, which can remain charged even when the drive is not powered. High voltage can be

present even when the warning indicator lights are off.

Failure to wait the specified time after power has been removed before performing service or repair work could result in death

or serious injury.

-Stop the motor.

-Disconnect AC mains, permanent magnet type motors, and remote DC-link supplies, including battery back-ups, UPS, and

DC-link connections to other drives.

-Wait for the capacitors to discharge fully. The minimum waiting time is specified in the table Discharge time and is also

visible on the nameplate on top of the drive.

-Before performing any service or repair work, use an appropriate voltage measuring device to make sure that the capacitors

are fully discharged.

Table 4: Discharge Time, VLT® HVAC Drive FC 102 and VLT® Refrigeration Drive FC 103

Voltage [V] Minimum waiting time (minutes)

4 7 15

200–240 1.1–3.7 kW (1.5–5 hp) – 5.5–45 kW (7.5–60 hp)

380–480 1.1–7.5 kW (1.5–10 hp) – 11–90 kW (15–125 hp)

525–600 1.1–7.5 kW (1.5–10 hp) – 11–90 kW (15–125 hp)

Safety

Operating Guide | VLT® Extended Relay Card MCB 113

AQ322553864968en-000101 / 130R0353

Voltage [V] Minimum waiting time (minutes)

525–690 – 1.1–7.5 kW (1.5–10 hp) (FC 102 only) 11–90 kW (15–125 hp) (FC 102 only)

Table 5: Discharge Time, VLT® AQUA Drive FC 202

Voltage [V] Minimum waiting time (minutes)

4 7 15

200–240 0.25–3.7 kW (0.34–5 hp) – 5.5–45 kW (7.5–60 hp)

380–480 0.37–7.5 kW (0.5–10 hp) – 11–90 kW (15–125 hp)

525–600 0.75–7.5 kW (1.0–10 hp) – 11–90 kW (15–125 hp)

525–690 – 1.1–7.5 kW (1.5–10 hp) 11–90 kW (15–125 hp)

Table 6: Discharge Time, VLT® AutomationDrive FC 301/FC 302

Voltage [V] Minimum waiting time (minutes)

4 7 15

200–240 0.25–3.7 kW (0.34–5 hp) – 5.5–37 kW (7.5–50 hp)

380–500 0.25–7.5 kW (0.34–10 hp) – 11–75 kW (15–100 hp)

525–600 0.75–7.5 kW (1–10 hp) – 11–75 kW (15–100 hp)

525–690 – 1.5–7.5 kW (2–10 hp) 11–75 kW (15–100 hp)

WARNING

LEAKAGE CURRENT HAZARD

Leakage currents exceed 3.5 mA. Failure to ground the drive properly can result in death or serious injury.

-Ensure the correct grounding of the equipment by a certified electrical installer.

WARNING

ROTATING SHAFTS

Contact with rotating shafts and electrical equipment can result in death or serious injury.

-Ensure that only trained and qualified personnel perform installation, start-up, and maintenance.

-Ensure that electrical work conforms to national and local electrical codes.

-Follow the procedures in this guide.

Safety

Operating Guide | VLT® Extended Relay Card MCB 113

AQ322553864968en-000101 / 130R0353| 9

3 Installation

3.1 Mechanical Installation

3.1.1 Installation in Enclosure Sizes A5–C4

NOTICE

For enclosure sizes A5–C4, only 1 C option can be installed at the time.

NOTICE

Do not mount the small fan for VLT® Extended Relay Card MCB 113, VLT® A/B in C Option Adapter MCF 106, or enclosure sizes

B4, C3, C4, D, E, and F.

RemoveJumper to activate Safe Stop

12 13 18 19 27 29 32 33 20

130bb457.11

Illustration 1: Installation of VLT® Extended Relay Card MCB 113 - Exploded View

• If only 1 C option is used, use the 40 mm mounting kit.

• If the MCB 113 is used with VLT® Motion Control MCO 305, use the 60 mm mounting kit.

3.2 Electrical Installation

3.2.1 Safety Instructions

See 2.1 Safety Precautions for general safety instructions.

Installation

Operating Guide | VLT® Extended Relay Card MCB 113

AQ322553864968en-000101 / 130R0353

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Danfoss Entraînement CC

Danfoss

Danfoss vlt aqua Manuel utilisateur

Danfoss

Danfoss VLT AutomationDrive EZ FC 321 Manuel utilisateur

Danfoss

Danfoss VLT Midi Drive FC 280 Manuel utilisateur

Danfoss

Danfoss VLT Decentral FCD 300 Manuel utilisateur

Danfoss

Danfoss VLT AutomationDrive FC 302 Mode d’emploi

Danfoss

Danfoss 176F6746 Manuel utilisateur

Danfoss

Danfoss VLT Midi Drive FC 280 Manuel utilisateur

Danfoss

Danfoss VLT series Mode d’emploi

Danfoss

Danfoss VLT AutomationDrive FC 302 Mode d'emploi

Danfoss

Danfoss VLT HVAC Manuel utilisateur

Danfoss

Danfoss VLT AutomationDrive FC 301 Mode d'emploi

Danfoss

Danfoss VLT HVAC Basic Drive FC 101 Mode d'emploi

Danfoss

Danfoss ADAP-KOOL Drive Mode d'emploi

Danfoss

Danfoss VLT AQUA Drive FC 202 Mode d’emploi

Danfoss

Danfoss VLT series Manuel utilisateur

Danfoss

Danfoss VLT HVAC Basic Drive FC 101 Manuel utilisateur

Danfoss

Danfoss VLT 6000 HVAC Profibus Manuel utilisateur

Danfoss

Danfoss VLT 4000 ME Manuel utilisateur

Danfoss

Danfoss VLT CDS 803 Manuel utilisateur

Danfoss

Danfoss VLT Manuel utilisateur

Danfoss

Danfoss VLT 6000 HVAC Series Fiche technique

Danfoss

Danfoss vlt fcd 302 Manuel utilisateur

Danfoss

Danfoss VLT Flow Drive FC 111 Mode d'emploi

Danfoss

Danfoss VLT Mode d'emploi

Manuels Entraînement CC populaires d'autres marques

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces

Chamberlain Garog

Chamberlain Garog D Series Manuel utilisateur

Parker

Parker PDS Series Manuel utilisateur

Festo

Festo DGC G Series Guide de configuration

Binks

Binks QS-5012-1-CE Manuel utilisateur

ABB

ABB ACQ580-01 Series Manuel d'installation

YASKAWA

YASKAWA CANopen SI-S3 Manuel utilisateur

GE D20A6 Manuel utilisateur

Unex

Unex MC-D-250-1000-050W-TW Manuel utilisateur

Geckodrive

Geckodrive G213V Manuel utilisateur

ABB

ABB RSYC-01 Manuel utilisateur

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuel du propriétaire

WEG

WEG DeviceNet CFW500 Manuel utilisateur

Siemens

Siemens SINAMICS G Fiche technique

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Mode d'emploi

SOMFY

SOMFY JR RU 30 Manuel utilisateur

Beckhoff

Beckhoff AX8911 Manuel de l'opérateur