Danfoss KP 1 Manuel utilisateur

Installation Guide

Pressure Control

Types KP 1, KP 2, KP 5, KP 7W, KP 7B

060R9746

Refrigerants

Auto reset:

KP 1, KP 2, KP 5, KP 7W

Manual reset:

KP 1, KP 5, KP 7B

HCFC and non-ammable HFC

Mounting

CAUTION:

Do not mount the control in a position where dirt,

sediment or oil will aect the operation of the control.

CAUTION:

Do not install these controls on ammonia systems.

Mounting requirements Ambient temperatures

t1 min. KP 1, KP 2, KP 5: -40 °F (-40 °C)

t1 min. KP 7: -13 °F (-25 °C)

t1max.: 149 °F (65 °C)

Test pressure (Ptest)

Enclosure

max. 1/8in.

(3 mm)

B: Enclosure: ~NEMA 1A: 10 – 32 UNC Threads

CAUTION:

The mounting panel must be plane to avoid damage of control.

Connections

Ptestmax.:

KP 1, KP 2: 285 psig (20 bar pe)

KP 5, KP 7: 510 psig (35 bar pe)

KP 2: 174 psig (12 bar pe)

Bellows Bellows

2 DKRCC.PI.C00.E1.22 / 520H6070 © Danfoss A/S (AC-MCI / jmn), 2012-11

CAUTION:

Disconnect power supply before wiring connections are made or service to avoid possible electrical shock

or damage to equipment. Do never touch live parts with your ngers or with any tool.

Wiring

All wiring should conform

to the National Electrical Code

and local regulations.

Terminal block

CAUTION:

Use terminal screws furnished

in the contact block.

Use tightening torque 20 lb. in (2.3 Nm).

Use copper wire only.

Contact load ratings

Load Option A

CUT-OUT on pressure drop

Wire terminals 1-4:

CUT-IN = High Set Point (HSP)

see “Setting”

CUT-OUT = Low Set Point (LSP)

see “Setting”

Load Option B

CUT-OUT on pressure rise

Wire terminals 1-2:

CUT-IN = Low Set Point (LSP)

see “Setting”

CUT-OUT = High Set Point (HSP)

see “Setting”

Example:

CUT-IN = 30 psig

CUT-OUT = 10 psig

This means :

CUT-IN = HSP = 30 psig

CUT-OUT = LSP = 10 psig

Example:

CUT-IN = 250 psig

CUT-OUT = 350 psig

This means :

CUT-IN = LSP = 250 psig

CUT-OUT = HSP = 350 psig

Bellows movement

on pressure rise

The free terminal can be

used for signal purpose.

120 V a.c. 16 FLA, 96 LRA

240 V a.c. 8 FLA, 48 LRA

240 V d.c. 12 W pilot duty

Terms 1-4 close on pressure rise

Terms 1-4 open on pressure drop

Terms 1-2 close on pressure drop

Terms 1-2 open on pressure rise

Bellows movement

on pressure drop

Note:

KP 1, man. reset is possible only

after a pressure rise

of 10 psi (0.7 bar). KP 5 and KP 7B,

man. reset is possible

only after a pressure drop

of respectively 43 psi (3.0 bar)

and 58 psi (4.0 bar)

Note:

KP 1, KP 5 and KP 7B with man. reset:

Push manual reset knob during

manual tripping.

TRIP (main lever)

use FINGERS ONLY!

(Do NOT use screwdriver)

To resume control operation

after safety cutout,

push reset knob as indicated.

Adjustment spindle(s) location

Type Dierential

KP 1 10 psi (0.7 bar)

KP 5 43 psi (3 bar)

KP 7B 58 psi (4 bar)

Auto reset KP 1, KP 2, KP 5, KP 7W

Manual reset KP 1, KP 5, KP 7B

A: Range

B: Dierential

A: Range

B: Dierential

Manual trip function

(Electrical contacts / wiring test)

Manual reset

Manual reset KP 1, KP 5, KP 7B

Setting

(see also “Wiring”)

KP 1 (auto reset), KP 2, KP 5, KP 7W, KP 7B

1. Adjust range spindle to desired HIGH SET POINT (HSP)

2. Adjust dierential spindle to desired DIFFERENTIAL (DIFF.)

1. Adjust range spindle to desired LOW SET POINT (LSP)

2. DIFFERENTIAL is xed Value printed on scale plate

HIGH SET POINT minus DIFFERENTIAL equals LOW SET POINT

Example: Example:

LOW SET POINT plus DIFFERENTIAL equals HIGH SET POINT

KP 1 (manual reset ONLY)

HSP – DIFF. = LSP

30 psig – 20 psi = 10 psig

(2.1 bar) (1.4 bar) (0.7 bar)

LSP + DIFF. = HSP

12 psig + 10 psi = 22 psig

(0.8 bar) (0.7 bar) (1.5 bar)

If terminals 1-4 are used: CUT-IN = HSP

CUT-OUT = LSP

If terminals 1-2 are used: CUT-IN = LSP

CUT-OUT = HSP

Note:

KP 5 (manual reset) and KP 7B have xed di.

Value printed on scale plate.

Adjustment

Note:

Remove lockplate before adjustment.

Replace lockplate after adjustment (if desired).

See instruction printed on top of control

KP 1: 3 psi (0.2 bar)/rev.

KP 2: 1.5 psi (0.1 bar)/rev.

KP 5: 4 psi (0.3 bar)/rev.

KP 7W: 7 psi (0.5 bar)/rev.

Range

Increase

360°

Decrease

360°

Increase

360°

Decrease

360°

6 mm

(15/64 in.)

Dierential

KP 1: 10 psi (0.7 bar)/rev.

KP 2: 7 psi (0.5 bar)/rev.

KP 5, 7W, 7B: 33 psi (2.3 bar)/rev.

Ce manuel convient aux modèles suivants

Autres manuels Danfoss Unité de contrôle

Danfoss

Danfoss REG-SA SS 15-40 Manuel utilisateur

Danfoss

Danfoss SVA-S 6-10 Manuel utilisateur

Danfoss

Danfoss AME 13 Manuel utilisateur

Danfoss

Danfoss Link SCM Manuel utilisateur

Danfoss

Danfoss ESMD Manuel utilisateur

Danfoss

Danfoss MCV111B Series Manuel utilisateur

Danfoss

Danfoss Colibri ETS 12C Manuel utilisateur

Danfoss

Danfoss PM 5-65 Manuel utilisateur

Danfoss

Danfoss SVA-DH Manuel utilisateur

Danfoss

Danfoss ASV-PV series Manuel utilisateur

Danfoss

Danfoss SVA-S Manuel utilisateur

Danfoss

Danfoss HPVB15 Manuel utilisateur

Danfoss

Danfoss EVRA 10 Manuel utilisateur

Danfoss

Danfoss EKC 102D Manuel utilisateur

Danfoss

Danfoss SFA 10 Manuel

Danfoss

Danfoss EVR 2 Manuel utilisateur

Danfoss

Danfoss PVG 120 Manuel utilisateur

Danfoss

Danfoss ICF 50-4 Manuel utilisateur

Danfoss

Danfoss EKF Series Manuel utilisateur

Danfoss

Danfoss 103E5 Instructions de montage

Danfoss

Danfoss VFS 2 Manuel utilisateur

Danfoss

Danfoss AK-CC 550A Mode d’emploi

Danfoss

Danfoss PM3 Instructions d'utilisation et d'entretien

Danfoss

Danfoss AFQM Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur