Danfoss AK-CC 550A Mode d’emploi

Troubleshooting Guidelines

AK-CC 550A

Service Guide

ADAP-KOOL® Refrigeration Control System

Service Guide |Troubleshooting Guidelines, AK-CC 550A

2 | AX278927426184en-000101

The following troubleshooting guidelines detail the process of

verifying proper setup of an AK-CC 550A when encountering

communication/oﬄine issues with an AK-SM 800 series controller.

System Manager Programming

• Complete Rescan

- On Network Nodes screen, select ‘Press for complete rescan’

*Also complete rescan if any of the items below required

adjustment

• Ensure proper channel enabled on Network Nodes screen of

system manager

- ‘Channel LONWORKS’ for LON RS485 comm loop

- ‘Channel MODBUS-RS485’for Modbus comm loop

• Verify no Duplicates in System Manager

- Check under Network Nodes->Duplicates

- If duplicates exist, identify case controller with mistaken

address, and update

• Verify address has been assigned to case controller in

program

- Verify under Conﬁguration->Control->Refrigeration-

>Addresses

AK-CC 550A Hardware

• Verify part # of AK-CC 550A. This will be printed on front of

controller below display

- For 084B8030, verify 230Vac to terminals 1&2

- For 084B8036, verify 115Vac to terminals 1&2

AK-CC 550A Programming

• Ensure address is set correctly, via parameter o03.

• Ensure application is set correctly, via parameter o61.

Comm Loop Wiring

• Verify intended form of communication to be used (Modbus

or LON RS485)

- For Modbus communication:

- Ensure comm wires are landed on terminals 57&58.

- Modbus loop is polarity sensitive, ensure polarity is

consistent throughout loop

- Ensure any other Modbus devices on the loop use 38400

baud rate

- For LON RS485 communication:

- Ensure comm wires are landed on terminals 52&53

- Ensure EKA 175 comm card is installed in port below

display.

- EOL resistor

- For 1 loop from system manager, ensure 120 ohm resistor

at end of loop and switch above comm plug in ‘On’

position

- For 2 loops from system manager, ensure 120 ohm resistor

at end of each loop and switch above comm plug in ‘Oﬀ’

position

• For either comm type, max distance is 4000’. Beyond this

distance, a repeater is needed

• For either comm type, max # of case controllers is 120 per

system manager

• For either comm type, an EIA 485 rated cable should be used

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products

already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.

Autres manuels pour AK-CC 550A

Autres manuels Danfoss Unité de contrôle

Danfoss

Danfoss ASV-M Manuel utilisateur

Danfoss

Danfoss SVA-S 6-10 Manuel utilisateur

Danfoss

Danfoss AB-QM DN 125 Manuel utilisateur

Danfoss

Danfoss VLT series Manuel utilisateur

Danfoss

Danfoss TR 6 Manuel utilisateur

Danfoss

Danfoss TS 12.5 Manuel utilisateur

Danfoss

Danfoss USV-I Manuel utilisateur

Danfoss

Danfoss PVG 32 Manuel

Danfoss

Danfoss PM 5-65 Manuel utilisateur

Danfoss

Danfoss EV220BW 15-50 Manuel utilisateur

Danfoss

Danfoss PVG 100 Manuel utilisateur

Danfoss

Danfoss XGE-4C Manuel utilisateur

Danfoss

Danfoss VLT AutomationDrive FC 302 Manuel utilisateur

Danfoss

Danfoss PVG 120 Manuel utilisateur

Danfoss

Danfoss JIP-WW Manuel utilisateur

Danfoss

Danfoss MSV-F2 DN15 - 400 Manuel utilisateur

Danfoss

Danfoss GBC 6s H Manuel utilisateur

Danfoss

Danfoss SFV Series Manuel utilisateur

Danfoss

Danfoss VLT HVAC Drive FC 102 Manuel utilisateur

Danfoss

Danfoss ETS 250 Manuel utilisateur

Danfoss

Danfoss EVR 2 Manuel utilisateur

Danfoss

Danfoss OPTYMA Manuel utilisateur

Danfoss

Danfoss ASV-PV series Manuel utilisateur

Danfoss

Danfoss PVG 100 Manuel

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur