Daikin BRC7E63W Manuel utilisateur

OPERATION MANUAL

Wireless Remote Controller Kit

MODELS

BRC7E63W

BRC7E66

Thank you for purchasing this Daikin air conditioner.

Carefully read this operation manual before using the air

conditioner. It will tell you how to use the unit properly and

help you if any trouble occurs. After reading the manual, file

it away for future reference.

[1]

PRIOR TO USE

This operation manual is exclusively for instructions on how to use

the wireless remote controller.

Read also the operation manual attached to the indoor unit and to the

outdoor unit for safe usage of the system and maintenance.

The air conditioner corresponding to this controller comes under the term

“appliances accessible to the general public”.

CONTENTS

PRIOR TO USE.......................................................................................... [1]

ILLUSTRATION .......................................................................................... [2]

1.SAFETY CONSIDERATIONS ................................................................... 1

2.NAMES AND FUNCTIONS OF

THE OPERATING SECTION..................................................................... 2

3.HANDLING FOR WIRELESS REMOTE CONTROLLER.......................... 3

4.OPERATION PROCEDURE...................................................................... 4

5.NOT MALFUNCTION OF THE AIR CONDITIONER............................... 10

6.HOW TO DIAGNOSE TROUBLE SPOTS ............................................... 10

1-1

1-2

DOWN

FAN

ON OFF

MHL

hr.

TEST

MODE

TIMER

RESERVE

CANCEL

DOWN

TEST

SWING

FAN

TIME

TEMP

ON OFF

MHL

hr.

TEST

[2]

COOL/HEAT CHANGEOVER

REMOTE CONTROL SWITCH

19 21 20

22 23

1-3 2

1English

Read the following cautions carefully and

use your equipment properly.

There are three kinds of safety cautions and

tips listed here as follows:

WARNING .. Improper handling can

lead to such serious

consequences as death or

severe injury.

CAUTION ... Improper handling can

lead to injury or damage.

It could also have serious

consequences under

certain conditions.

NOTE.......... These instructions will

ensure proper use of the

equipment.

Be sure to follow these important safety cau-

tions.

Keep these warning sheets handy so that

you can refer to them if needed.

Also, if this equipment is transferred to a new

user, make sure to hand over this user’s man-

ual to the new user.

WARNING

Do not expose yourself directly to the

cool air currents too long nor allow the

air in the room to become too cold.

Doing so may make you feel sick or dam-

age your health.

If you detect any abnormality (such as

the smell of fire), turn off the power

and contact your dealer for instruc-

tions.

If you keep using the air conditioner

under these conditions, it will eventually

break down, and could cause electric

shocks or catch fire.

Ask your dealer to install your equip-

ment.

Improper installation could cause water

leakage, electric shocks or fire.

1. SAFETY CONSIDER-

ATION S

Ask your dealer to perform servicing

or repairs whenever necessary.

Improper servicing or repairs could cause

water leakage, electric shocks or fire.

Do not stick your fingers or any other

objects into the air inlet, air outlet or

air direction vanes during operation.

The high-speed fan is dangerous and

could cause injury.

Ask your dealer to remove and

reinstall your equipment whenever

necessary.

Improper installation could cause water

leakage, electric shocks or fire.

CAUTION

Do not use the air conditioner for pur-

poses other than air conditioning.

Do not use the air conditioner for special

purposes such as preserving or protect-

ing food, animals, plants, precision

machinery or works of art, since the qual-

ity of such items could be adversely

affected.

When using the air conditioner with

other heating equipment, ventilate the

room from time to time.

Inadequate ventilation could cause an

oxygen shortage.

Do not expose your pets or plants to

the air current.

They may be adversely affected.

Do not operate the air conditioner with

a wet hand.

Otherwise, you could receive an electric

shock.

Do not place any burning appliance in

the air current from the air conditioner,

since such appliance may suffer

incomplete combustion.

Never place nor use any inflammable

sprays near the air conditioner, since

such sprays could cause a fire.

English 2

2. NAMES AND FUNCTIONS

OF THE OPERATING SEC-

TION (Fig. 1, 2)

DISPLAY “ ” (SIGNAL

TRANSMISSION)

This lights up when a signal is being

transmitted.

DISPLAY “ ” “ ” “ ” “ ”

“ ” (OPERATION MODE)

This display shows the current OPER-

ATION MODE. For straight cooling

type, “ ” (Auto) and “ ” (Heating)

are not installed.

DISPLAY “ ” (

SET TEMPERATURE

)

This display shows the set tempera-

ture.

DISPLAY “ ”

(PROGRAMMED TIME)

This display shows PROGRAMMED

TIME of the system start or stop.

5DISPLAY “ ” (AIR FLOW FLAP)

Refer to page 7.

6DISPLAY “ ” “ ” (FAN SPEED)

The display shows the set fan speed.

DISPLAY “ ”

(INSPECTION/ TEST OPERATION)

When the INSPECTION/TEST OPER-

ATION BUTTON is pressed, the display

shows the system mode is in.

ON/OFF BUTTON

Press the button and the system will

start. Press the button again and the

system will stop.

FAN SPEED CONTROL BUTTON

Press this button to select the fan

speed, HIGH or LOW, of your choice.

MHL

hr. hr.

TEST

TEMPERATURE SETTING BUTTON

Use this button for SETTING TEMPER-

ATURE (Operates with the front cover

of the remote controller closed.)

PROGRAMMING TIMER BUTTON

Use this button for programming

“START and/or STOP”time. (Operates

with the front cover of the remote con-

troller opened.)

12 TIMER MODE START/STOP BUTTON

Refer to page 7.

13 TIMER RESERVE/CANCEL BUTTON

Refer to page 8.

AIR FLOW DIRECTION ADJUST

BUTTON

Refer to page 7.

OPERATION MODE SELECTOR

BUTTON

Press this button to select OPERATION

MODE.

FILTER SIGN RESET BUTTON

Refer to the section of MAINTENANCE

in the operation manual attached to the

indoor unit.

INSPECTION/TEST OPERATION

BUTTON

This button is used only by qualified

service persons for maintenance

purposes.

EMERGENCY OPERATION SWITCH

This switch is readily used if the remote

controller does not work.

RECEIVER

This receives the signals from the

remote controller.

OPERATING INDICATOR LAMP

(Red)

This lamp stays lit while the air

conditioner runs. It flashes when the

unit is in trouble.

21 TIMER INDICATOR LAMP (Green)

This lamp stays lit while the timer is set.

3English

AIR FILTER CLEANING TIME

INDICATOR LAMP (Red)

Lights up when it is time to clean the air

filter.

DEFROST LAMP (Orange)

Lights up when the defrosting opera-

tion has started. (For straight cooling

type this lamp does not turn on.)

FAN/AIR CONDITIONING SELECTOR

SWITCH

Set the switch to “”(FAN) for FAN

and “”(A/C) for HEAT or COOL.

COOL/HEAT CHANGEOVER

SWITCH

Set the switch to “”(COOL) for

COOL and “”(HEAT) for HEAT.

NOTES

•For the sake of explanation, all indica-

tions are shown on the display in Figure 1

contrary to actual running situations.

•Fig. 1-2 shows the remote controller with

the front cover opened.

•Fig. 1-3 shows this remote controller can

be used in conjunction with the one pro-

vided with the VRV system.

•If the air filter cleaning time indicator lamp

lights up, clean the air filter as explained

in the operation manual provided with the

indoor unit.

After cleaning and reinstalling the air fil-

ter, press the filter sign reset button on

the remote controller. The air filter clean-

ing time indicator lamp on the receiver will

go out.

Precautions in handling remote con-

troller

Direct the transmitting part of the remote

controller to the receiving part of the air

conditioner.

If something blocks the transmitting and

receiving path of the indoor unit and the

remote controller as curtains, it will not

operate.

Transmitting distance is approximately 7 m.

Do not drop or get it wet.

It may be damaged.

Never press the button of the remote con-

troller with a hard, pointed object.

The remote controller may be damaged.

Installation site

•It is possible that signals will not be

received in rooms that have electronic flu-

orescent lighting. Please consult with the

salesman before buying new fluorescent

lights.

•If the remote controller operated some

other electrical apparatus, move that

machine away or consult your dealer.

3. HANDLING FOR

WIRELESS REMOTE

CONTROLLER

Receiver

2 short beeps

from the receiver

indicates that the

transmission is

properly done.

English 4

Placing the remote controller in the

remote controller holder

Install the remote controller holder to a wall

or a pillar with the attached screw. (Make

sure it transmits)

How to put the dry batteries

(1) Remove the back cover

of the remote controller

to the direction pointed

by the arrow mark.

(2) Put the batteries

Use two LR03<IEC>

dry cell batteries. Put

dry batteries correctly

to fit their (+) and (–).

(3) Close the cover

When to change batteries

Under normal use, batteries last about a

year. However, change them whenever the

indoor unit doesn’t respond or responds

slowly to commands, or if the display

becomes dark.

Placing the remote

controller

Slide from above

Remote

controller

holder

Removing the

remote controller

Pull it upward

[CAUTIONS]

•Replace all batteries at the same time, do

not use new and old batteries intermixed.

•In case the remote controller is not used

for a long time take out all batteries in order

to prevent liquid leak of the battery.

IN THE CASE OF CENTRALIZED

CONTROL SYSTEM

If the indoor unit is under centralized control, it

is necessary to switch the remote controller’s

setting.

In this case, contact your DAIKIN dealer.

Refer to figure 1 on page [1]

•Operating procedure varies with heat

pump type and cooling only type. Contact

your Daikin dealer to confirm your system

type.

•To protect the unit, turn on the main power

switch 6 hours before operation.

•If the main power supply is turned off dur-

ing operation, operation will restart auto-

matically after the power turns back on

again.

Operate in the following order.

•AUTOMATIC OPERATION can be

selected only by Heat recovery system.

•For cooling only type, “COOLING”, and

“FAN”and “DRY”operation are able to

select.

4. OPERATION PROCEDURE

COOLING, HEATING, AUTOMATIC,

FAN, AND PROGRAM DRY

OPERATION

5English

〈〈

〈〈〈〈

〈〈FOR SYSTEMS WITHOUT COOL/

HEAT CHANGEOVER REMOTE

CONTROL SWITCH〉〉

〉〉〉〉

〉〉

Refer to figure 1-1, 2 on page [1]

OPERATION MODE

SELECTOR

Press OPERATION MODE SELECTOR

button several times and select the

OPERATION MODE of your choice as

follows.

 COOLING OPERATION .................... “”

 HEATING OPERATION ..................... “”

 AUTOMATIC OPERATION ................ “”

•In this operation mode, COOL/HEAT

changeover is automatically conducted.

 FAN OPERATION .............................. “”

 DRY OPERATION ............................. “”

•The function of this program is to

decrease the humidity in your room with

the minimum temperature decrease.

•Micro computer automatically

determines TEMPERATURE and FAN

SPEED.

•This system does not go into operation if

the room temperature is below 16°C.

ON/OFF

Press ON/OFF button

OPERATION lamp lights up or goes off and

the system starts or stops OPERATION.

NOTE

•Do not turn OFF power immediately after

the unit stops. Then, wait no less than

5 minutes.

Water is leaking or there is something else

wrong with the unit.

〈〈

〈〈〈〈

〈〈FOR SYSTEMS WITH COOL/HEAT

CHANGEOVER REMOTE CONTROL

SWITCH〉〉

〉〉〉〉

〉〉

Refer to figure 1-1,3 on page [1]

MODE

ON OFF

OPERATION MODE

SELECTOR

(1) Select OPERATION MODE with the

COOL/HEAT CHANGEOVER REMOTE

CONTROL SWITCH as follows.

 COOLING OPERATION ............. “”

 HEATING OPERATION .............. “”

 FAN OPERATION....................... “”

 DRY OPERATION ...................... “”

•See “FOR SYSTEM WITHOUT COOL/

HEAT CHANGEOVER REMOTE CON-

TROL SWITCH”for details on dry opera-

tion.

(2) Press OPERATION MODE SELECTOR

button several times and select “”

(This operation is only available during

dry operation.)

ON/OFF

Press ON/OFF button

OPERATION lamp lights up or goes off and

the system starts or stops OPERATION.

NOTE

•Do not turn OFF power immediately after

the unit stops. Then, wait no less than

5 minutes.

Water is leaking or there is something else

wrong with the unit.

[EXPLANATION OF HEATING OPERA-

TION]

DEFROST OPERATION

ON OFF

English 6

•As the frost on the coil of an outdoor unit

increase, heating effect decreases and the

system goes into DEFROST OPERATION.

•The fan operation stops and the

DEFROST lamp of the indoor unit goes on.

After 6 to 8 minutes (maximum 10 min-

utes) of DEFROST OPERATION, the sys-

tem returns to HEATING OPERATION.

Heating capacity & Outdoor air

temperature

•Heating capacity drops as outdoor air tem-

perature lowers. If feeling cold, use

another heater at the same time as this air

conditioner.

•Hot air is circulated to warm the room. It

will take some time from when the air con-

ditioner is first started until the entire room

becomes warm. The internal fan automat-

ically turns at low speed until the air condi-

tioner reaches a certain temperature on

the inside. In this situation, all you can do

is wait.

•If hot air accumulates on the ceiling and

feet are left feeling cold, it is recommended

to use a circulator. For details, contact the

place of purchase.

For programming TEMPERATURE, FAN

SPEED and AIR FLOW DIRECTION, follow

the procedure shown below.

TEMPERATURE SETTING

Press TEMPERATURE SETTING but-

ton and program the setting tempera-

ture.

Each time this button is pressed,

setting temperature rises 1°C.

Each time this button is pressed,

setting temperature lowers 1°C.

ADJUSTMENT

DOWN

In case of automatic operation

Each time this button is pressed,

setting temperature shifts to “H”

side.

Each time this button is pressed,

setting temperature shifts to “L”

side.

[°C]

•The setting is impossible for fan operation.

NOTE

•The setting temperature range of the

remote controller is 16°C to 32°C.

FAN SPEED CONTROL

Press FAN SPEED CONTROL button.

High or Low fan speed can be selected.

The microchip may sometimes control the

fan speed in order to protect the unit.

AIR FLOW DIRECTION

ADJUST

•There are 2 ways of adjusting the air dis-

charge angle.

1. A. Up and down adjustment

2. B. Left and right direction

Fig. 1

DOWN

HML

Setting

temperature 25 23 22 21 19

FAN

SWING

A. UP AND DOWN

DIRECTION

B. LEFT AND RIGHT

DIRECTION

7English

A. UP AND DOWN DIRECTION

•The movable limit of the flap is change-

able. Contact your Daikin dealer for

details.

Press the AIR FLOW DIRECTION

ADJUST button to select the air direc-

tion as shown below.

DISPLAY appears and the

air flow direction continu-

ously varies. (Automatic

swing setting)

Press AIR FLOW DIREC-

TION ADJUST button to

select the air direction of

your choice.

DISPLAY vanishes the air

flow direction is fixed

(Fixed air flow direction

setting).

MOVEMENT OF THE AIR FLOW FLAP

For the following conditions, micro computer

controls the air flow direction so it may be

different from the display.

NOTE

•If you try cooling or programmed drying,

while the flaps are facing downward, air

flow direction may change unexpectedly.

There is nothing wrong with the equip-

ment. This serves to prevent dew formed

Operation

mode

Cooling Heating

Operation

condition

•When room

temperature

is lower than

the set tem-

perature

•When room

temperature

is higher than

the set tem-

perature

•At defrost

operation

•When operating continuously

at horizontal air flow direction

on parts in the air discharge outlet from

dripping.

•Operation mode includes automatic

operation.

B. LEFT AND RIGHT DIRECTION

•Adjusting air flow direction in the left and

right direction. (Refer to Fig. 1)

NOTE

•Only make adjustments after you have

stopped the air flow direction swing in a

position.

•Stop flaps from swinging before trying to

angle them. Working while the flaps are

moving may get your fingers pinched.

Operate in the following order.

•The timer is operated in the following two

ways.

Programming the stop time ( )

.... The system stops

operating after the set time has elapsed.

Programming the start time ( )

.... The system starts

operating after the set time has elapsed.

•The timer can be programmed a maximum

of 72 hours.

•The start and the stop time can be simulta-

neously programmed.

TIMER MODE START/

STOP

Press the TIMER MODE START/STOP

button several times and select the

mode on the display.

The display flashes.

For setting the timer stop .... “”

For setting the timer start .... “”

PROGRAM TIMER OPERATION

TIMER

Autres manuels pour BRC7E63W

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Daikin Télécommande

Daikin

Daikin BRC7E61W Manuel d'installation

Daikin

Daikin BRC1D619 Manuel utilisateur

Daikin

Daikin SRC-COA Manuel utilisateur

Daikin

Daikin BRC301B61 Manuel utilisateur

Daikin

Daikin BRC1E63 Manuel utilisateur

Daikin

Daikin BRC1H81K Manuel utilisateur

Daikin

Daikin BRC1H81W7 Guide de l'utilisateur

Daikin

Daikin BRC2A71 Manuel utilisateur

Daikin

Daikin BRC7E83 Manuel utilisateur

Daikin

Daikin BRC7EA628 Manuel utilisateur

Daikin

Daikin BRC7EA63W Manuel utilisateur

Daikin

Daikin BRC1E71 Manuel utilisateur

Daikin

Daikin BRC1E52B7 Manuel utilisateur

Daikin

Daikin BRC1E73 Manuel utilisateur

Daikin

Daikin 4PW71247-1-KAD Manuel utilisateur

Daikin

Daikin BRC073A4 Fiche d'information produit

Daikin

Daikin BRC1E72 Manuel utilisateur

Daikin

Daikin BRC1E52A7 Manuel utilisateur

Daikin

Daikin BRC2E52C7 Manuel utilisateur

Daikin

Daikin BRC1H51W Manuel utilisateur

Daikin

Daikin BRC7EB518 Manuel utilisateur

Daikin

Daikin BRC1D71 Manuel utilisateur

Daikin

Daikin BRC1H63W Manuel utilisateur

Daikin

Daikin BRC1H71W Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation